6. All costs of removal and reinstallation of the fan are the sole responsibility of the owner of the fan and not the store that sold the fan or Fanimation. 7. Fanimation reserves the right to modify or discontinue any product at any time and may substitute any part under this warranty.
• Blade Arm Set (5) accessories not designated for use with this product (blade arm to motor) Pan Head Screw by Fanimation could result in personal injury or • Blade Set (5) property damage. • Housing Light Kit Assembly – Phillips Screwdriver, 4”...
8 - 9 feet above the floor for optimal This produces a gentle updraft, which forces warm air airflow. Consult your Fanimation Retailer for optional near the ceiling down into the occupied space. mounting accessories.
How to Assemble Your Ceiling Fan 1. Remove the hanger ball portion from the downrod/hangerball assembly by loosening the set screw in the hanger ball until the ball falls freely down the downrod. Remove the pin from the DOWNROD downrod, then remove the hanger ball. Retain the pin and hanger ball for reinstallation in Step 4 (Figure 1).
How to Assemble Your Ceiling Fan (continued) 6. Cut off excess lead wire approximately 6 to 9 inches above top of the top of the downrod. Strip insulation off 1/2-inch from the end of each lead wire (Figure 6). 6 TO 9 INCHES DOWNROD NOTE: All set screws must be checked, and retightened...
How to Wire Your Ceiling Fan WARNING To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before hanging MAIN FUSE BOX (Figure 1). NOTE: If you are not sure if the outlet box is grounded, contact a licensed electrician for advice, as Figure 1 it must be grounded for safe operation.
Page 8
How to Wire Your Ceiling Fan (continued) WARNING HARDWARE USED: Check to see that all connections are tight, including WIRE ground, and that no bare wire is visible at the wire CONNECTORS connectors except for the ground wire. Do not operate fan until the blades are in place.
How to Install Your Canopy Housing 1. Remove one of the two shoulder screws in the hanger bracket. Loosen the second shoulder screw without fully removing it. Assemble canopy by CANOPY rotating key slot in canopy over shoulder screw in SHOULDER hanger bracket.
Page 10
How to Assemble the Blades and Light Kit (continued) 3. Remove one of the three screws in the support SCREWS (3) bracket at the bottom of the motor assembly. Slightly loosen the remaining two screws. Assemble the housing light kit assembly to the support bracket using the two key slots in the socket plate.
How to Operate Your Ceiling Fan 1. Restore electrical power to the outlet box by turning the electricity on at the main fuse box (Figure 1). WARNING MAIN FUSE BOX Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire connectors, except for the ground wire.
Trouble Shooting WARNING For your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan. Trouble Probable Cause Suggested Remedy 1. Fuse or circuit breaker blown. 1. Check main and branch circuit fuses or circuit breakers. 2.
Parts List Model No. FP8000** Hanger Bracket Assembly w/Screws APGAC110RBL - l l Canopy Screw Cover Assembly APPAC1101** n i l Fan Motor Assembly AMA8000** y (AP800008**) 019** Glass (P800009OP) Socket Plate Assembly AP800011WH 100W E11 Minican Light Bulb (1) PPE11B100 t i n Lower Steel Cap Assembly...
The Akira ™ Ventilador de techo Acabados: OB, PW and PN Peso neto 26.46 lb (12 kg) Modelo N.º FP8000 MANUAL DEL PROPIETARIO LEA Y GUARDE ESTAS INSTRUCCIONES...
Page 17
GARANTÍA LIMITADA DE POR VIDA DEL MOTOR - Si se produjera una falla en alguna de las partes del motor de su ventilador debido a un defecto en los materiales o en la fabricación durante el tiempo de vida del comprador original, Fanimation proporcionará la pieza de repuesto sin cargo una vez que el ventilador defectuoso sea devuelto a nuestro centro de servicios nacional.
La sustitución de piezas o accesorios no – 1/4”-20 x 14mm • Cubierta de unión del motor designados por Fanimation para usar con este producto (brazo aspas en el motor) • Soportes de aspas (5) podría ocasionar lesiones personales o daños en el tornillo de cabeza troncocónica...
óptimo. del reloj. Esto produce una suave corriente ascendente, Consulte en su tienda minorista de Fanimation para que obliga al aire cálido que se acumula cerca del techo a obtener accesorios de montaje opcionales.
Cómo ensamblar el ventilador de techo 1. Extraiga la pieza de la bola colgante de la unidad de Pasador la bola colgante / varilla aflojando el tornillo de presión de la bola colgante hasta que la bola se libere de la Bola para colgar varilla.
Cómo ensamblar el ventilador de techo (cont.) Corte el exceso de cable aproximadamente de 15 a 23 cm (6 a 9 pulgadas) por encima de la parte superior del barral. Pele 1,2 cm (½˝) del aislamiento en cada extremo del cable. (Figura 6) NOTA: Se deben revisar todos los tornillos de fijación y la varilla volver a ajustarlos cuando sea necesario antes de realizar...
Cómo realizar la instalación eléctrica del ventilador de techo ▲ADVERTENCIA Para evitar posibles descargas eléctricas, asegúrese de que la electricidad esté desconectada en la caja de fusibles PRINCIPAL CAJA DE principal antes de realizar la instalación eléctrica. FUSIBLES (Figura 1) NOTA: Si no está...
Page 23
Cómo realizar la instalación eléctrica del ventilador de techo (Cont.) ADVERTENCIA Aditamentos utilizados Verifique que todas las conexiones estén ajustadas, Conectores incluida la conexión a tierra, y que no haya conductores de cable desnudos visibles en los conectores, excepto el conductor con conexión a tierra.
Page 24
Cómo instalar la carcasa de la cubierta 1. Retire uno de los dos tornillos de reborde de la abrazadera para colgar. Afloje el segundo tornillo Cubierta para el de reborde sin retirarlo del todo. Ensamble la base tornillo del girando el chavetero de la base sobre el tornillo de Tornillo capuchón de fijación (2)
Page 25
Cómo ensamblar los Blades y kit de luz (cont.) Extraiga uno de los tres tornillos del soporte Tornillos (3) ubicado en la parte inferior de la unidad del motor. Afloje levemente los otros dos tornil- los. Instale la unidad de la placa de luz en el soporte utilizando las dos ranuras principales de la placa de conexión.
Cómo utilizar su ventilador de techo Restaure la fuente de alimentación de la toma de corriente enciendo la electricidad del fusible principal. (Figura 1) ADVERTENCIA PRINCIPAL CAJA DE FUSIBLES Compruebe que todas las conexiones realizadas correctamente, incluyendo la toma de tierra, y que no se visualizan ningún cable pelado en los conectores de cables, con la excepción del cable de toma de Figura 1...
Solución de problemas ▲ ADVERTENCIA Para su propia seguridad, desconecte la electricidad de la caja de fusibles o disyuntor antes de solucionar problemas en su ventilador. Problema Causa posible Solución sugerida 1. EL VENTILADOR NO 1. El fusible o el disyuntor están fundidos. 1.
Lista de piezas Modelos N.° FP8000** Pieza # N.° Descripción N.° de Ref. Unidad del soporte de suspensión APGAC110RBL ADRAC1-45** Unidad del barral/de la semiesfera (4.5) Capuchón de techo P800001** Cubierta para el tornillo del capuchón APPAC1101** Cubierta de unión del motor AP800002** Unidad del motor del ventilador AMA8000**...
Page 30
10983 Bennett Parkway Zionsville, IN 46077 Llame sin cargo al (888) 567-2055 FAX (866) 482-5215 Desde fuera de los EE.UU., llame al (317) 733-4113 Visite nuestro sitio Web en www.fanimation.com Copyright 2011 Fanimation 2011/01...