GE Monogram ZBD1870 Installation Instructions Manual
Built-in dishwashers
Hide thumbs
Also See for Monogram ZBD1870:
- Owner's manual (24 pages) ,
- Installation instructions manual (16 pages) ,
- Owner's manual (24 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Owner's Manual
Advertisement
Table of Contents
Related Manuals for GE Monogram ZBD1870
Summary of Contents for GE Monogram ZBD1870
- Page 1 Appliances Installation Instructions If gou have questions, call 800.626.2000 or visit our website at: www.monogram.com Built-In Dishwashers ZBD1850* ZBD1870 *For ZBD1850 also refer to the instructions provided on the template packed with that model...
-
Page 2: Table Of Contents
Product FOR YOUR SAFETY failure due to improper installation is not covered under the GE Appliance Warranty. See warranty information. Read and observe all CAUTIONS and WARNINGS shown Completion Time - 1 to 3 Hours. New installations require throughout these instructions. -
Page 3: Installation Preparation
installation Preparation PARTS SUPPLIED: [] Two #8 Phillips head wood screws, 5/8" long to secure dishwasher to underside of countertop (in literature package). 2 Wood Screws MATERIALS YOU WILL NEED: Ferrule, compression nut and 90 ° Elbow (3/8" NPT external thread on one end, opposite end sized to fit water supplg) [] Thread seal tape 90°... -
Page 4: Prepare Dishwasher Enclosure
installation Preparation • The dishwasher must be installed so that drain hose is no PREPARE DISHWASHER ENCLOSURE more than 10' in length for proper drainage. To reduce the risk of electric shock, fire, or injury to persons, the installer must ensure that the dishwasher is completelg enclosed 34-1/2"+... -
Page 5: Materials You Will Need
installation Preparation PREPARE ELECTRICAL WIRING -i x FORPERSONAL SAFETY: Remove house fuse or open circuit breaker before beginning installation. Do not use 1-1/2" Dia. an extension cord or adapter plug with this Hole (Max.) appliance. from Cabinet Electrical Requirements • This appliance must be supplied with 120V, 60Hz., and connected to an individual properly grounded branch circuit protected by a 15 or 20 ampere circuit breaker or time delay fuse. -
Page 6: Prepare Hot Water Line
If adjustments are needed, see Step 1A. If no adjustments are needed, skip to Step 2. STEP 1A ADJUST DOOR SPRINGS (IF NECESSARY) FOR ZBD1870 MODELS For ZBD1850 models, refer to the instruction provided on the template packed with that model. - Page 7 Installation Instructions Lay the dishwasher on its back. Remove the four screws Remove the side panels and set the dishwasher upright. securing the toekick to the dishwasher, and remove the toekick. To adjust the door springs: Pull the spring adjustment pin out of the holes, insert in the next highest or lowest hole and test again.
-
Page 8: Step 2 Adjust Leveling Legs
Installation Instructions STEP 2 ADJUST LEVELING LEGS STEP 4 INSTALL POWER CORD Hove the dishwasher close to the installation location and lag Skip this step if dishwesher will be direct wired. it on its back. Use Power Cord Kit WX09X70910, available for purchase from an authorized GEAppliance Dealer. -
Page 9: Step 6, Position Water Line And House Wiring
Installation Instructions STEP 8 SLIDE DISHWASHER PARTIALLY STEP 6 POSITION WATER LINE AND INTO CABINET HOUSE WIRING DO NOT PUSH AGAINST FRONT PANELWITH KNEES. , Position water supply line and house wiring on the floor of DAMAGE WILL OCCUR. the opening to avoid interference with base of dishwasher , Slide dishwasher into the opening a few inches at a time. -
Page 10: Step 9, Position Dishwasher Under Countertop
installation instructions STEP 9 POSITION DISHWASHER UNDER Reposition Dishwasher COU NTERTOP / _ \ by Grasping Both • Push the dishwasher into the cabinet. • Push the sides with your hands. Do not use your knee against s With Hands the door since door damage will occur. -
Page 11: Step !0, Level Dishwasher
Installation Instructions STEP 10 LEVEL DISHWASHER STEP 11 SECURE DISHWASHER COUNTERTOP OR CABINET IN PORTANT- Dishwasher must be level for proper In this step gou will need Side-Mounting dish rack operation and wash performance. Bracket the 2 Phillips special head •... -
Page 12: Step !2, Connect Water Supplg
Installation Instructions STEP 12 CONNECT WATER SUPPLY DRAIN LINE INSTALLATION Connect water supplg line to 90 ° elbow. • Connect drain line to air gap, waste tee or disposer using • Slide compression nut, either previously determined method. then ferrule over end of CompressionNut water line. -
Page 13: Step 15 Pretest Check List
Installation Instructions STEP 14 CONNECT POWER SUPPLY STEP 15 PRETEST CHECK LIST Skip this step if equipped with power cord. Review this list after installing your dishwasher to avoid Verifg that power is turned offat the source. charges for a service call that is not covered by your Remove junction box cover "A". -
Page 14: Step !6, Dishwasher Wet Test
Run the dishw(]sher through (]nother fill (]nd dr(]in cycle. STEP 18 LITERATURE Check for le(]ks (]nd correct if required. ,, Be sure to le(]ve complete liter(]ture p(]ck(]ge (]nd Inst(]ll(]tion [] At the end of dr(]in, open door (]nd press ON/OFF button to Instructions with the consumer.