Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Ecler DPA600
Summary of Contents for Ecler DPA600
- Page 1 USER MANUAL MANUAL DE INSTRUCCIONES NOTICE D’EMPLOI BEDIENUNGSANLEITUNG...
-
Page 3: Table Of Contents
7. FUNCTION DIAGRAM 8. TECHNICAL CHARACTERISTICS 9. DIAGRAMS 9.1. Figures 9.2. Block diagram All numbers subject to variation due to production tolerances. ECLER S.A. reserves the right to make changes or improvements in manufacturing or design which may affect specifications. -
Page 4: Important Note
DPA series amplifiers come with a 3-year warranty. 1.1. Precautions The DPA600/1000/1400/2000 consumes a maximum power of 830VA / 1250VA / 1720VA / 3115VA, we therefore recommend a mains wire not inferior to 2,5mm and a (circuit breaker) superior to 10A/220VAC (15A/220VAC DPA2000) (data for one amplifier). -
Page 5: Installation
- Delay - Phase inversion - Signal generator - Remote level control Please refer to your Ecler distributor if you need to install a UCM or AMIC processor module inside a DPA power amplifier. 3. INSTALLATION 3.1. Location, assembly, ventilation The DPA600/1000/1400/2000 amplifiers are 2 RU high 19'' rack modules. -
Page 6: Mains Connection
3.2. Mains connection The DPA amplifiers are fed with alternate currents, depending on the country, of 110-120, 220-240V 47-63Hz. (see characteristics in the back of the unit) consuming: MODEL DPA600 DPA1000 DPA1400 DPA2000 CONSUMPTION 830VA 1250VA 1720VA 3115VA The mains cables must not be near the shielded cables carrying the audio signal, as this could cause humming. -
Page 7: Output Connections
3.6. Output connections The OUTPUT section on the rear panel features Speakon connectors (12). Whenever you need to operate the amplifier in BRIDGED mode (mono or bridged), you must set the “STEREO BRIDGED" Switch (11) to BRIDGED. The input signal is taken from the CHANNEL 1 connector and the signal output to the loudspeaker is on pins 2+ and 2- of the Speakon connector “CH1”. -
Page 8: Cleaning
CLIP/PROT indicators functioning as CLIP indicator. These illuminate when the signal given to the loudspeakers is 1.5dB before the real clip. This CLIP system takes into account the possible variations in the mains voltage always giving a real indication even if the electric mains varies. -
Page 9: Function List
6. FUNCTION LIST 1. Input attenuator 2. Combined clip and protection indicator, CLIP/PROT 3. Thermal protection indicator, TH 4. Signal present indicator, SP 5. Illuminated mains switch 6. Mains socket 7. Switch to disconnect chassis earth/electrical Ground, GND LINK 8. Earth terminal, GND 9. -
Page 10: Technical Characteristics
8. TECHNICAL CHARACTERISTICS 8. CARACTERÍSTICAS TÉCNICAS 8. CARACTERISTIQUES TECHNIQUES 8. TECHNISCHE DATEN DPA600 DPA1000 DPA1400 DPA2000 POWER 20-20kHz 1% THD 2 Stereo 410 WRMS 682 WRMS 990 WRMS 1420 WRMS 4 Stereo 275 WRMS 440 WRMS 635 WRMS 940 WRMS 8... -
Page 11: Diagrams
9. DIAGRAMS 9. DIAGRAMAS 9. SCHÉMAS 9. DIAGRAMME 9.1. Figures 9.1. Figuras 9.1. Schémas 9.1. Abbildungen... -
Page 13: Block Diagram
9.2. Block diagram 9.2. Diagrama de bloques 9.2. Diagramme de blocs 9.2. Blockschatbild... - Page 15 ECLER Laboratorio de electro-acústica S.A. Motors 166-168, 08038 Barcelona, Spain INTERNET http://www.ecler.com e-mail: info@ecler.es 50.0093.01.04...