Related Manuals for MULTIQUIP tp7X
Summary of Contents for MULTIQUIP tp7X
-
Page 1: Electric Motor
OperatiOn Manual MODel tp7X tile Saw (electric MOtOr) Revision #0 (03/04/11) To find the latest revision of this publication, visit our website at: www.multiquip.com THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES. -
Page 2: Proposition 65 Warning
ALWAYS work in a well ventilated area, and work with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles. page 2 — Tp7X TILe SaW • operaTIon manuaL — rev. #0 (03/04/11) -
Page 3: Silicosis/Respiratory Warnings
NIOSH/MSHA for the materials being used. Tp7X TILe SaW • operaTIon manuaL — rev. #0 (03/04/11) — page 3... -
Page 4: Table Of Contents
Operation ............22-23 Maintenance ............. 24-27 Wiring Diagram (Electric Motor) ......28 Troubleshooting (Blade) ......... 30 Troubleshooting (Saw) ........... 31 NOTICE Specifications are subject to change without notice. page 4 — Tp7X TILe SaW • operaTIon manuaL — rev. #0 (03/04/11) - Page 5 Tp7X TILe SaW • operaTIon manuaL — rev. #0 (03/04/11) — page 5...
-
Page 6: Safety Information
CouLD result in DeaTH or SerIouS InJury. CauTIon Indicates a hazardous situation which, if not avoided, CouLD result in mInor or moDeraTe InJury. NOTICE Addresses practices not related to personal injury. page 6 — Tp7X TILe SaW • operaTIon manuaL — rev. #0 (03/04/11) -
Page 7: General Safety
„ aLWayS check the equipment for loosened threads or bolts before starting. „ Do noT use the equipment for any purpose other than its intended purposes or applications. Tp7X TILe SaW • operaTIon manuaL — rev. #0 (03/04/11) — page 7... - Page 8 „ Adhere to the blade manufacturer’s recommendations WarnIng on handling, storage and safe usage of blades. „ Rotating blade can cut and crush. aLWayS keep hands and feet clear while operating the saw. page 8 — Tp7X TILe SaW • operaTIon manuaL — rev. #0 (03/04/11)
- Page 9 NOTICE „ aLWayS make certain that proper power or extension cord has been selected for the job. „ Protect the cable from heat, oil, and sharp edges. Tp7X TILe SaW • operaTIon manuaL — rev. #0 (03/04/11) — page 9...
-
Page 10: Specifications
Water pump 115V, 60 Hz — 230 GPH Weight 55 lbs. (25 kg) Table 2. electric motor Specifications Horsepower volts amps motor rpm 21,500 RPM Cycle phase Class page 10 — Tp7X TILe SaW • operaTIon manuaL — rev. #0 (03/04/11) -
Page 11: Dimensions
DiMenSiOnS Figure 1. Dimensions Table 3. Dimension reference Letter Dimensions 31.9 in. (811 mm) 19.6 in. (49-8 mm) 20.4 in. (518 mm) Tp7X TILe SaW • operaTIon manuaL — rev. #0 (03/04/11) — page 11... -
Page 12: General Information
7-inch (178 mm) diamond blades that match the material being cut. Ask your dealer, or call Multiquip about your specific cutting application. page 12 — Tp7X TILe SaW • operaTIon manuaL — rev. #0 (03/04/11) - Page 13 Tp7X TILe SaW • operaTIon manuaL — rev. #0 (03/04/11) — page 13...
-
Page 14: Saw Components
Saw cOMpOnentS Figure 2. Saw Components page 14 — Tp7X TILe SaW • operaTIon manuaL — rev. #0 (03/04/11) -
Page 15: Saw Components
11. Blade guard Brushes — Prevents foreign matter and debris from accumulating on the saw blade. Replace brushes immediately when they become worn or damaged. Tp7X TILe SaW • operaTIon manuaL — rev. #0 (03/04/11) — page 15... -
Page 16: Electric Motor Components/Set-Up
„ Drain Plug „ Owner’s Manual 3. After teh saw stand is assembled, seat the saw securely on top of the stand. „ Universal Wrench „ MasterGuide Template Base page 16 — Tp7X TILe SaW • operaTIon manuaL — rev. #0 (03/04/11) -
Page 17: Set-Up
5. Make certain that the water hose will not come in contact with the blade or interfere with any moving parts. BLADE GUARD WATER PUMP WATER HOSES BEARING HOUSING DRAIN PLUG Figure 6. Connecting the Water Pump Tp7X TILe SaW • operaTIon manuaL — rev. #0 (03/04/11) — page 17... - Page 18 “under cutting” condition brought about by highly abrasive material or improper under cutting core protection. page 18 — Tp7X TILe SaW • operaTIon manuaL — rev. #0 (03/04/11)
-
Page 19: Blade Installation
Inspect segment blades for segment cracking or loss. Do not cut too deep or too fast into the material. Do not cut any material not recommended by blade Do not use damaged blades. manufacturer. Tp7X TILe SaW • operaTIon manuaL — rev. #0 (03/04/11) — page 19... -
Page 20: Set-Up
If possible use a specifically shown dimensions on each notch). ground fault circuit interrupter to protect the operator from possible electric shock. page 20 — Tp7X TILe SaW • operaTIon manuaL — rev. #0 (03/04/11) -
Page 21: Sawing Guides
Tighten the threaded knob to secure the miter block in place. 3. Place material onto miter block and you are ready to cut. Figure 13. Miter Block Tp7X TILe SaW • operaTIon manuaL — rev. #0 (03/04/11) — page 21... -
Page 22: Operation
The possibility exists of electrical shock, electrocution which could cause Figure 15. Power ON/OFF Switch (ON) severe bodily harm, even death. page 22 — Tp7X TILe SaW • operaTIon manuaL — rev. #0 (03/04/11) -
Page 23: Operation
4. Using a soft cloth, clean any excess debris or residue that may have accumulated on the saw. 5. Store saw in a clean dry location where it will be out of the reach of children. Tp7X TILe SaW • operaTIon manuaL — rev. #0 (03/04/11) — page 23... -
Page 24: Maintenance
It may be necessary to clean the tray out twice 15. Grease pivot bearings periodically. a day in heavy cutting. The sludge is abrasive and will shorten the life of the water pump and blades. page 24 — Tp7X TILe SaW • operaTIon manuaL — rev. #0 (03/04/11) -
Page 25: Maintenance Intervals
„ With the saw blade removed, switch on the motor for an instant and switch it off again. If the motor does not run, have the machine inspected by a qualified electrician. Figure 17. Water Tray Removal Tp7X TILe SaW • operaTIon manuaL — rev. #0 (03/04/11) — page 25... -
Page 26: Water Pump Maintenance
5. Carefully loosen the pulley and belt outward slightly, so there is a little slack in the belt. 6. Take off the old belt and replace with a new one. page 26 — Tp7X TILe SaW • operaTIon manuaL — rev. #0 (03/04/11) - Page 27 Do not adjust the bearing housing pulley. 7. After aligning the belt, tighten the hex screw. 8. Replace the belt guard and lock into place using 4 screws. Tp7X TILe SaW • operaTIon manuaL — rev. #0 (03/04/11) — page 27...
-
Page 28: Wiring Diagram (Electric Motor)
White Power Outlet for Water Pump Motor Black Green Power Cable Black Black Switch White White White Overcurrent Breaker Wiring Box Figure 20. Electric Motor Wiring Diagram page 28 — Tp7X TILe SaW • operaTIon manuaL — rev. #0 (03/04/11) - Page 29 Tp7X TILe SaW • operaTIon manuaL — rev. #0 (03/04/11) — page 29...
-
Page 30: Troubleshooting (Blade)
Grinding marks on the saw blade Poor tension in blade material Have the saw blade tensioned The material feed is too high; proceed more Too much load on the saw blade slowly page 30 — Tp7X TILe SaW • operaTIon manuaL — rev. #0 (03/04/11) -
Page 31: Troubleshooting (Saw)
Clean the filter of the water pump water at all Pump wheel of the immersion pump is Disassemble the immersion pump and clean it blocked by dirt Tp7X TILe SaW • operaTIon manuaL — rev. #0 (03/04/11) — page 31... - Page 32 © COPYRIGHT 2011, MULTIQUIP INC. Multiquip Inc and the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the property of their respective owners and used with permission.
Need help?
Do you have a question about the tp7X and is the answer not in the manual?
Questions and answers