Table of Contents
Advertisement
P3907005
Memoirs Stately 3 Hole Basin
Mixer
Installation and User Guide
MODEL NUMBERS
454W–3S 454W–4S 454W-4V
Important :- Please quote the above model number(s) when ordering spares.
IMPORTANT!
Installer: This manual is the property of the customer and must
be retained with the product for maintenance and operational
purposes.
Advertisement
Table of Contents
Related Manuals for Kohler Memoirs Stately 3 Hole Basin Mixer
Summary of Contents for Kohler Memoirs Stately 3 Hole Basin Mixer
- Page 1 P3907005 Memoirs Stately 3 Hole Basin Mixer Installation and User Guide MODEL NUMBERS 454W–3S 454W–4S 454W-4V Important :- Please quote the above model number(s) when ordering spares. IMPORTANT! Installer: This manual is the property of the customer and must be retained with the product for maintenance and operational purposes.
-
Page 2: Table Of Contents
CONTENTS DESCRIPTION ................. SAFETY : WARNINGS ............. DIMENSIONS ................SPECIFICATION ..............Pressures ................. Plumbing Connections ............. INSTALLATION ................. Before You Begin ............. Install the Mixer ..............Installing the Drain ............Install the Link for Drain ........... Finish The Installation ............USER MAINTENANCE ............ -
Page 3: Description
DESCRIPTION The Memoirs Stately 3 Hole Basin Mixer is a mixer for basins with mixer holes between 200mm and 410mm centres. It has either cross handles or lever handles, and has a pop-up drain with a lift rod and tailpiece. -
Page 4: Dimensions
DIMENSIONS 114mm 410mm MAX. 200mm MIN. 17mm 32mm 46mm 44mm 29mm DIA. 81mm MAX. 48mm 24mm 102mm 54mm 14mm 64mm 62mm 67mm 87mm 89mm 1-1/4" O.DIA. 102mm 48mm 48mm STATELY STATELY LEVER CROSS Pop-Up Drain HANDLE HANDLE 64mm 83mm 48mm STATELY DECO HANDLE... -
Page 5: Specification
SPECIFICATION Pressures The minimum recommended operating pressure is 0.5 bar. For optimum performance, a minimum operating pressure of 1.0 bar is recommended. Plumbing Connections Hot (H) and Cold (C) inlets must be connected to the correct inlet supplies. 1023012-W2-B... -
Page 6: Installation
INSTALLATION Before You Begin Turn off the water supply. The plumbing installation must comply with Water Supply Regulations/Bye-laws (Scotland), Building Regulations or any particular regulations and practices, specified by the local water company or water undertakers. The installation should be carried out by a plumber or contractor who is registered with, or is a member of an association such as: Institute of Plumbing (IOP), throughout the UK. -
Page 7: Install The Mixer
Install the Mixer Apply Sealant Metal Washer P3907020 Apply a ring of sealant to the underside of the spout in accordance with the manufacturer’s instructions. Fit the spout through the top of the basin. Install the washer and the nut. Use a spanner to tighten the nut. 1023012-W2-B... - Page 8 Concealing Plate Fibre Washer Locknut P3907100 Thread the locknuts half way down the valve bodies. Slide the fibre washers over the valve bodies. Insert the valve bodies into the mounting holes from the bottom of the basin. Make sure that the valve body marked ‘COLD’ is installed in the right hand hole (as viewed from the front of the basin).
- Page 9 Skirt Valve Body P3907030 Align the handle splines onto the valve splines and thread the handle skirt onto the concealing plate. 10. Loosely secure the valve bodies into position with the locknuts, but do not tighten. 1023012-W2-B...
- Page 10 Valve Valve Valve Valve Outlet Outlet Outlet Outlet Body Body Body Body Spout Spout VALVE ALIGNMENT VALVE ALIGNMENT 410mm (centre to centre) 200mm (centre to centre) P3902160 11. Position the valve bodies in their correct orientation, usually facing towards the spout for maximum valve centres, and facing outwards for minimum centres.
- Page 11 Plastic Rubber Gasket Washer Threaded Bushing Supply Tee Rubber Washer Flexible Hose P3907040/1 17. Remove and retain the guide tube nut and O-ring from the supply tee sleeve. 18. Insert the plastic gasket and rubber washer into the tee. Screw the tee onto the spout until hand tight.
- Page 12 Valve Body Supply Hose Spanner Water Supply Inlet P3902190 22. Connect the water supply hoses to the valve inlets. Do not use thread sealant. Do not over tighten. 23. Connect the water supply hoses to the water supplies. Avoid kinking the hoses.
-
Page 13: Installing The Drain
Installing the Drain Fixture Flange Apply Silicone Sealant Gasket Washer Drain Body Seal Hole P3907115 Remove the protective cover from the flange. Apply sealant around the underside of the waste in accordance with the manufacturer’s instructions. Assemble the nut, flat washer and tapered gasket (tapered side up) fully onto the body. -
Page 14: Install The Link For Drain
Install the Link for Drain Thumb Screw Link Clip P3923110 Slide the clip and the link onto the rod with the thumbscrew facing towards the rear of the basin. Move the link to the desired position by squeezing the clip and sliding it along the rod. - Page 15 Lift Rod Handle Thumb Screw Link P3907050 Slide the lift rod through the hole in the spout and through the hole in the link. Tighten the thumbscrew on the link so that the lift rod knob is touching the spout. Install the basin in accordance with its instructions.
-
Page 16: Finish The Installation
Finish The Installation Aerator P3907090 Make sure that both of the tap handles are turned off (HOT= clockwise, COLD = anti-clockwise). Turn on the main water supply and check for leaks. Remove the aerator from the spout. Turn on both hot and cold valves and run water through the spout for one minute to remove any debris. -
Page 17: User Maintenance
USER MAINTENANCE Cleaning Caution! Risk of product damage. Many cleaners contain abrasive and chemical substances, and should not be used for cleaning stainless steel, enamel, plated or plastic fittings. These finishes should be cleaned using a mild washing up detergent or soap solution, rinsed and then wiped dry with a soft clean cloth. -
Page 18: Ceramic Valve Replacement
Ceramic Valve Replacement REMOVE INSTALL Ceramic Valve Unit P3902200 Turn off the water supply and relieve pressure through the tap. Remove the lever assembly from the valve by unscrewing the handle skirt. Remove the existing valve. Thread the new ceramic valve into the valve body until hand tight. Caution! Risk of product damage. -
Page 19: Spare Parts
SPARE PARTS 454W-4S 454W-3S 454W-4V P3907080/1 1023012-W2-B... - Page 20 1025208** 1000282** 1000283** Handle Handle Handle 88490 Grub Screw 87536 88490 Screw Grub Screw Trim Ring Washer Skirt Stem O-Ring Concealing Plate 78125 Spline Adapter Washer Lock Nut 460.63 (pair) 3005837 1/2" Valve Assembly Hose 86189 Fibre Washer (x 3) Hose ** Variation and/or finish/colour code may be required when ordering.
- Page 21 1021961** Lift Rod Lift Rod Spout Assembly Washer Insert, Aerator Housing Washer 1006005-BC Memoirs Aerator Assembly Washer (x 3) Gasket (x 3) Bushing (x 2) 1030358 ** Variation and/or finish/colour code may be required when ordering. P3907070/3 1023012-W2-B...
- Page 22 71130-A-** Drain O-Ring (Plastic) Stopper (Metal) Screw Trim Ring Seal Link Washer Clip Washer Body (With Overflow) 1034145-FJ-RP Washer Adapter Tailpiece **Finish/color code must be specified when ordering. P3907120/1 1023012-W2-B...
-
Page 23: Notes
NOTES 1023012-W2-B... -
Page 24: Customer Service
CUSTOMER SERVICE Guarantee of Quality Kohler UK guarantee products against any defect of materials or workmanship for the following periods Ceramic Ware and Cast Products Stainless Steel Products and, Acrylic Baths Shower Valves, Taps, Cistern Bathroom Furniture and Whirlpool / Spa Baths...