Download  Print this page

Haier 10557172 Operation Manual

Floor unit
Hide thumbs

Advertisement

Quick Links

FLOOR UNIT

OPERATION MANUAL

HFU-09HA03(B)/R1
HFU-12HA03(B)/R1
HFU-09H03/R2(DB)
HFU-12H03/R2(DB)
HFU-18H03/R2(DB)
Please read this operation manual before using the air conditioner.
No.0010557172

Advertisement

loading

  Related Manuals for Haier 10557172

  Summary of Contents for Haier 10557172

  • Page 1: Operation Manual

    FLOOR UNIT OPERATION MANUAL HFU-09HA03(B)/R1 HFU-12HA03(B)/R1 HFU-09H03/R2(DB) HFU-12H03/R2(DB) HFU-18H03/R2(DB) Please read this operation manual before using the air conditioner. No.0010557172...
  • Page 2: Safety Instructions And Warnings

    Damaged air conditioners are not to be put into operation. In case of doubt, consult your supplier. Use of the air conditioner is to be carried out in strict compliance with the relative instructions set forth in the User's Guide.
  • Page 3 Cautions Do not obstruct or cover the ventilation grille of the air conditoner.Do not put fingers or any other things into the inlet/outlet and swing louver. Do not allow children to play with the air conditioner.In no case should children be allowed to sit on the outdoor unit.
  • Page 4: Safety Instruction

    Installation Please call Sales/Service Shop for the Installation. Do not attempt to install the air conditioner by yourself because improper works may cause electric shock, fire, water leakage. Installation in a inadequate place may cause accidents. Do not install in the following place.
  • Page 5 Cautions When abnormality such as burnt-small found, immediately stop the operation button and contact sales shop. Connect power supply cord to the outlet completely STRICT ENFORCEMENT Do not use power supply cord in a bundle. PROHIBITION Do not start or stop the operation by disconnecting the power supply cord and so on.
  • Page 6: Parts And Functions

    Parts and Functions Indoor unit Outdoor unit HFU-09HA03(B)/R1 HFU-09H03/R2(DB) HFU-12H03/R2(DB) OUTLET CONNECTING PIPING AND ELECTRICAL WIRING INLET DRAIN HOSE 1.OUTLET 2.CONTROL PANEL 3.INLET 4.FILTER (inside) 5.OUTLET HFU-12HA03(B)/R1 HFU-18H03/R2(DB)
  • Page 7: Air Flow Selection

    Make air flow selection according to what suits you. When setting the air flow selection switch to Air conditioner automatically decides the appropriate blowing pattern depending on the operating mode/situation. During Dry mode, so that cold air does not come into direct contact with people, air is blown upper air outlet.
  • Page 8 Parts and Functions Remote Controller 1.TIMER Used to select TIMER ON, TIMER OFF, TIMER ON-OFF 2.HOUR Used to set clock and timer setting. 3.CLOCK Used to set correct time. Note: 1. The following functions and related displays are not available for all models: Display of humidifying and atmosphere humidity.
  • Page 9 Parts and Functions Clock Set When unit is started for the first time and after replacing batteries in remote controller, clock should be adjusted as follows: 1. Press CLOCK button,"AM" or "PM" flashes. 2. Press to set correct time. Each press will increase or decrease 1 min.
  • Page 10: Auto Operation

    Press FAN button. For each press, fan speed changes as follows: Remote controller: Air conditioner is running under displayed wind speed When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature. 5.Unit stop Press ON/OFF button, the unit stops.
  • Page 11: Cool Operation

    Press FAN button. For each press, fan speed changes as follows: Remote controller: Air conditioner is running under displayed wind speed When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature. 5.Unit stop Press ON/OFF button, the unit stops.
  • Page 12: Dry Operation

    4.Fan speed selection Press FAN button. For each press, fan speed changes as follows: Remote controller: Air conditioner is running under displayed fan speed. In DRY mode, when room temperature becomes lower than temp.setting+2 at LOW speed regardless of FAN setting.
  • Page 13: Fan Operation

    Operation FAN Operation Remote controller 1. Unit start Press ON/OFF on the indoor unit, or press ON/OFFon the remote controller, unit starts. Previous operation status appears on LCD display (no timer and sleep). 2.Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO...
  • Page 14: Heat Operation

    Air conditioner is running under displayed wind speed IN HEAT mode, warm air will blow out after a short period of the time due to cold-draft prevention function. When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature.
  • Page 15: Adjusting The Air Flow Direction

    Operation Adjusting the Air Flow Direction You can adjust the air flow direction to increase your comfort Adjusting the flap Notes on flap angles When SWING is selected, the flap swinging range depends on the operation mode.(See the figure.) COOL/DRY HEAT NOTE Unless [SWING] is selected, you should set the flap at a...
  • Page 16: Sleep Operation

    Operation SLEEP Operation Before going to bed , you can simply press the SLEEP button and unit will operation in SLEEP mode and bring you a sound sleep. Use of SLEEP function After the unit starts, set the operation status, then press SLEEP button before which the clock must be adjusted and time being set.
  • Page 17: Timer On/Off Operation

    Operation Timer On/Off Operation Remote controller Hints: After replacing batteries or a power failure happens, time setting should be reset. Remote controller possesses memory function, when use TIMER mode next time,just press SET button after mode selecting if time setting is the same as previous one. Set clock correctly before starting TIMER operation.
  • Page 18 Operation TIMER On-Off Operation Remote Controller Set clock correctly before starting TIMER operation. 1. After unit starts, select your desired operation mode Operation mode will be displayed on LCD. 2. Timer mode selection Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as follows: Remote controller: TIMER ON...
  • Page 19: Power Operation

    Operation POWER/SOFT Operation POWER Operation When you need rapid heating or cooling, you can use this funciton. Selecting of POWER operation Press POWER/SOFT button. Every time the button is pressed,display changes as follows: Stop the display at In POWER operation status: In HEAT or COOL mode, fan speed automatically runs in HI mode for 15 min then returns to original status setting.
  • Page 20: Test Operation

    5 seconds. After you hear the "BI" sound twice, release your finger from the switch, the test operation starts and the air conditioner starts with the air flow speed setting "Hi". Unit stop(to cancel test operation) Push the test run switch or operate with remote controller to cancel the test run.
  • Page 21: Operation Hints

    When sudden power failure happens during unit operation in power failure resume mode,if the air conditioner is not desired for use in a long period, please shut off the power supply in case that the unit automatially resume operation when power is re-supplied, or press...
  • Page 22: Maintenance

    Maintenance Cleaning of the unit Turn off the power switch Take off the air inlet grill First switch off the power supply, take off the screw cap, loosen the screw with cross screwdriver. Clean the filter Use water or vacuum cleaner to remove dust.
  • Page 23 Maintenance Maintenance at the end of application season On a fine day, unit shall be started and operate in FAN mode for about half a day unit the inside of the unit becomes thoroughly dry. Turn off the unit operation switch and power on/off. Otherwise, there will be some electricity consumption even the unit is in stop status.
  • Page 24: Troubleshooting

    When the electric plug is pulled out and reinserted, the protection circuit will work for 3 minutes to protect the air conditioner. During unit operation or at stop, a swishing or gurgling noise may be heard. At first 2-3 minutes after unit start, this noise is more noticeable.
  • Page 25: Installation Of Indoor Unit

    Installation Manual of Room Air Conditioner Figure.1 Figure.2 Figure.3 Installation of outdoor unit selection of installation place Place strong enough to support the unit and will not cause vibration and noise. Place where discharged wind and noise does not cause a nuisance to the neighbors.
  • Page 26: Standard Accessories

    Installation Manual of Room Air Conditioner Tool necessary 1.Screw driver 2.Hacksaw 3.70mm dia. hole core drill 4.Spanner(dia.17,27mm) 5.Spanner(14,17,27mm) 6.Pipe cutter 7.Flaring tool 8.Knife 9.Nipper 10.Gas leakage detector or soap water 11.Measuring tape 12.Reamer 13.Refrigerant oil Standard accessories Following parts shall be field...
  • Page 27 Installation Manual of Room Air Conditioner 3. Piping connection Connecting method Apply refrigerant oil at half union and flare nut. To bent a pipe, give the roundness as large as possible not to crash the pipe. When connecting pipe, hold the pipe center to center then screw nut on by hand, refer to Fig.
  • Page 28 After attaching the each caps, check the gas leakage around the caps. CAUTION: 1.If the refrigerant of the air conditioner leaks, it is necessary to discharge all the refrigerant. Vacuumize first, then charge the liquid refrigerant into air conditioner according to the amount marked on the name plate.
  • Page 29 After attaching the each caps, check the gas leakage around the caps. CAUTION: 1.If the refrigerant of the air conditioner leaks, it is necessary to discharge all the refrigerant. Vacuumize first, then charge the liquid refrigerant into air conditioner according to the amount marked on the name plate.
  • Page 30: Wiring Of Indoor Unit

    When connecting indoor and outdoor wire, check the number on indoor and outdoor terminal blocks. Terminals of same number and same color shall be connected by the same wire. Incorrect wiring may damage air conditioner's control or cause operation failure. Indoor unit...
  • Page 31 Air conditioner must use an exclusive line(over 20A) . The type of power supply wire is HF05VV-3G2.5mm When installation air conditioner in a wet place, try to use a circuit breaker against current leakage. For installation in other places, use circuit breaker as for as possible.