NEC Dterm Cordless II User Manual
  1. Manuals
  2. Brands
  3. NEC Manuals
  4. Cordless Telephone
  5. Dterm Cordless II
  6. User manual

NEC Dterm Cordless II User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
term
D
®
Cordless II
User's Guide

Advertisement

Table of Contents
loading

Related Manuals for NEC Dterm Cordless II

Summary of Contents for NEC Dterm Cordless II

  • Page 1 term ® Cordless II User’s Guide...

  • Page 2: Handset Controls And Functions

    Handset Controls and Functions Ringer ON/OFF Slide Switch Conference (CONF) Key Message Display Transfer (TRANSFER) Key Hold (HOLD) Key Redial (REDIAL) or Desk/Cordless Softkey Switch Key Talk (TALK) Key Channel (CHAN) Key Numeric Keypad Ringer/Volume (R/VOL) Microphone Mute (MUTE) Key Headset Jack...

  • Page 3: Using Your Phone

    USING YOUR PHONE Before using your telephone you must ensure that: Each base unit is placed at least five feet apart. > The antenna is raised to the vertical position. > Before plugging the telephone line into your new telephone, the rechargeable nickel-cadmium battery pack must be fully charged.

  • Page 4: Programming Mode

    Programming Mode Press and hold and # at the same time, then press TALK. ‘F1=LK01’ shows in the display and the F1 LED flashes red. > Press MUTE to select the function/line key to program. (LK01 - LK04 and Off-hook Ring) >...

  • Page 5: Receiving Volume

    Muting Press MUTE during conversation. The ‘TALK’ icon blinks and the voice through the microphone is muted. > Press MUTE again to cancel the muted condition. (Finishing the conversation also cancels the mute condition.) The ‘TALK’ icon stops blinking. > Conferencing This feature allows the user to set up a 3-party conference.
  • Page 6 Ringer ON/OFF Slide Switch When the ringer ON/OFF slide switch (located at side of handset) is turned off, the handset does not ring or vibrate and the ringer ‘OFF’ icon appears in the display. When the ring ‘OFF’ icon appears and the terminal is idle for five minutes, the ring ‘OFF’ icon turns off to save battery life. When operation resumes, the ring ‘OFF’...

  • Page 7: Changing Channels

    Programming Desk/Cordless Softkey Switching (Redial key) This feature switches from Desk to Cordless mode only. Make sure the base unit is in Desk mode. Remove the battery. Press and hold the and # keys on the handset at the same time. Install the battery while pressing and holding these keys.

  • Page 8: Traveling Out-Of-Range

    Traveling Out of Range If function keys (F1 ~ F4) are pressed and no connection is established within five seconds, the telephone times out and returns to standby mode. When using the TALK key, the handset sounds an error tone and ‘NO SERVICE’ displays in the LCD.

  • Page 9: Cleaning Battery Contacts

    Cleaning Battery Contacts To maintain a good charge, it is important to clean all battery contacts on the handset and base about once a month. Use a dry cloth or, if necessary, use a pencil eraser. Do not use any liquids or solvents.
  • Page 10 Optional Available Parts Part Description Stock Number Headset 730602 Charging Unit without AC Adapter 730621 Spring-type Belt Clip 730620 AC Adapter for Charging Unit 730619 AC Adapter for Base Unit 730618 Leather Carry Case 730626 Replacement Battery 730622...
  • Page 11 Notes...
  • Page 12 © 2001 NEC America, Inc. Document Revision 1 The material contained herein is subject to change without prior notice at the sole discretion of NEC America, For more information contact: Inc. NEC America, Inc. 6555 N State Highway 161 Irving, TX 75039-2402 term ®...

Table of Contents