Table of Contents
Advertisement
USER MANUAL
Thank you very much for choosing the
iiyama LCD monitor.
We recommend that you take a few
minutes to read carefully through this
brief but comprehensive manual before
installing and switching on the monitor.
Please keep this manual in a safe place
for your future reference.
ENGLISH
ENGLISH
DEUTSCH
FRANCAIS
NEDERLANDS
Advertisement
Table of Contents
Related Manuals for Iiyama ProLite E1702S
Summary of Contents for Iiyama ProLite E1702S
-
Page 1: User Manual
ENGLISH DEUTSCH FRANCAIS NEDERLANDS Thank you very much for choosing the iiyama LCD monitor. We recommend that you take a few minutes to read carefully through this brief but comprehensive manual before installing and switching on the monitor. Please keep this manual in a safe place... - Page 2 Congratulations! The display you have just purchased carries the TCO’03 Displays label. This means that your display is designed, manufactured and tested according to some of the strictest quality and environmental requirements in the world. This makes for a high performance product, designed with the user in focus that also minimizes the impact on our natural environment.
-
Page 3: Fcc Declaration Of Conformity
To meet the FCC requirements, you should use a signal cable with ferrite core at both ends. CAUTION Changes or modifications not expressly approved by iiyama could void the users authority to operate the device under FCC compliance regulations. CANADIAN DEPARTMENT OF COMMUNICATIONS COMPLIANCE... -
Page 4: Table Of Contents
FEATURES ..........................4 CHECKING THE CONTENTS OF THE PACKAGE ................ 5 FITTING AND REMOVAL OF BASE : ProLite E1702S / E1702SV / E1702WS / E1702WSV ..6 CONTROLS AND CONNECTORS : ProLite E1702S / E1702SV / E1702WS / E1702WSV ..7 CONTROLS AND CONNECTORS : ProLite B1702S .............. -
Page 5: For Your Safety
STOP OPERATING THE MONITOR WHEN YOU SENSE TROUBLE If you notice any abnormal phenomena such as smoke, strange sounds or fumes, unplug the monitor and contact your dealer or iiyama service center immediately. Further use may be dangerous and can cause fire or electric shock. -
Page 6: Installation Location
CAUTION INSTALLATION LOCATION Do not install the monitor where sudden temperature changes may occur, or in humid, dusty or smoky areas as it may cause fire, electric shock or damage. You should also avoid areas where the sun shines directly on the monitor. DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION The monitor may topple and cause injury if not suitably located. -
Page 7: Special Notes On Lcd Monitors
Power Switch for hours. Contact your dealer or iiyama service center for the backlight replacement when the screen is dark, flickering or not lighting up. Never attempt to replace it by yourself. -
Page 8: Before You Operate The Monitor
FEATURES 43cm (17") TFT Color LCD Monitor Supports Resolutions up to 1280 × 1024 : ProLite E1702S / E1702SV / B1702S Supports Resolutions up to 1440 × 900 : ProLite E1702WS / E1702WSV High Contrast 1000:1 / High Brightness 300cd/m... -
Page 9: Checking The Contents Of The Package
CHECKING THE CONTENTS OF THE PACKAGE The following accessories are included in your package. Check to see if they are enclosed with the monitor. If anything is missing or damaged, please contact your local iiyama dealer or regional iiyama office. -
Page 10: Fitting And Removal Of Base : Prolite E1702S / E1702Sv / E1702Ws / E1702Wsv
FITTING AND REMOVAL OF BASE : ProLite E1702S / E1702SV / E1702WS / E1702WSV CAUTION Install the stand on a stable surface. The monitor may cause injury or damage if it falls or is dropped. Do not give a strong impact to the monitor. It may cause damage. -
Page 11: Controls And Connectors : Prolite E1702S / E1702Sv / E1702Ws / E1702Wsv
CONTROLS AND CONNECTORS : ProLite E1702S / E1702SV / E1702WS / E1702WSV <Front> <Back> A Menu Button (MENU) B + Button ( C Power Switch ( D – Button ( E Auto Button (AUTO) F Power Indicator Blue: Normal operation... -
Page 12: Controls And Connectors : Prolite B1702S
CONTROLS AND CONNECTORS : ProLite B1702S <Front> <Back> A Menu Button (MENU) B + Button ( C Power Switch ( D – Button ( E Auto Button (AUTO) F Power Indicator Blue: Normal operation NOTE Orange: Power Management Auto (Signal Select) When no signal is received from the system, the display enters into its Power Management Mode reducing power consumption to <... -
Page 13: Connecting Your Monitor : Prolite E1702S / E1702Sv / E1702Ws / E1702Wsv
The cable supplied with the monitor is for a standard 15 pin D-Sub connector. If a special cable is required please contact your local iiyama dealer or regional iiyama office. For connection to Macintosh computers, contact your local iiyama dealer or regional iiyama office for a suitable adaptor. -
Page 14: Connecting Your Monitor : Prolite B1702S
The cable supplied with the monitor is for a standard 15 pin D-Sub connector. If a special cable is required please contact your local iiyama dealer or regional iiyama office. For connection to Macintosh computers, contact your local iiyama dealer or regional iiyama office for a suitable adaptor. -
Page 15: Computer Setting
Change to the desired signal timing listed on page 34: COMPLIANT TIMING. Windows 95/98/2000/Me/XP/Vista Plug & Play The iiyama LCD monitor complies with DDC2B of VESA standard. The Plug & Play function runs on Windows 95/98/2000/Me/XP/Vista by connecting the monitor to DDC2B compliant computer with the Signal Cable supplied. -
Page 16: Adjusting The Height And The Viewing Angle : Prolite B1702S
ADJUSTING THE HEIGHT AND THE VIEWING ANGLE : ProLite B1702S For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's Height and angle to your own preference. Hold the stand so that the monitor does not topple 110mm when you change the monitor’s angle. -
Page 17: Operating The Monitor
OPERATING THE MONITOR To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT TIMING shown on page 34. You are also able to adjust the picture by following the button operation shown below. For more detailed adjustments, see page 22 for SCREEN ADJUSTMENTS. -
Page 18: Adjustment Menu Contents
With the OSD menu off, pressing and holding the Menu and ‘-‘ Buttons simultaneously for a period of at least 7 seconds will enable and disable the OSD Lock Out mode. is displayed while Lock Out is active. * Available for ProLite E1702S / E1702WS / B1702S only. OPERATING THE MONITOR... -
Page 19: Analog Input
Analog Input Menu : 1 (Analog) M e n u : 1 1280 × 1024 H : 8 0 . 0 K H z V : 7 5 . 0 H z Adjustment Item Problem / Option Button to Press Too dark Brightness * Direct... -
Page 20: Screen Adjustments
1 2 3 4 5 Adjust the picture quality at resolutions of less than 1280 × 1024 (ProLite E1702S / E1702SV / B1702S), 1440 × 900 (ProLite E1702WS / E1702WSV). You can change the picture quality from 1 to 5 (sharp to soft). - Page 21 Menu : 2 (Analog) Adjustment Item Problem / Option Normal Gamma Mode1 High contrast Mode2 Dark Normal Economy Mode Mode1 Brightness of back-light is reduced. Mode2 Brightness of back-light is reduced more than Mode1. NOTE is displayed while Economy Mode is active. Return to Menu Highlight “Menu : 2”...
- Page 22 In Power Management Mode input switching is disabled. Return to Menu. Reset Factory-preset data is restored. Return to Menu Highlight “Menu : 3” again. * Available for ProLite E1702S / E1702WS / B1702S only. See page 14 for Direct adjustment. Direct OPERATING THE MONITOR...
- Page 23 Digital Input : Available for ProLite E1702S / E1702WS / B1702S only. Menu:1 1280 × 1024 H : 8 0 . 0 K H z V : 7 5 . 0 H z Adjustment Item Problem / Option Button to Press...
- Page 24 Menu : 1 (Digital) Adjustment Item Problem / Option Normal Economy Mode Mode1 Brightness of back-light is reduced. Mode2 Brightness of back-light is reduced more than Mode1. NOTE is displayed while Economy Mode is active. Return to Menu Highlight “Menu : 1” again. OPERATING THE MONITOR...
- Page 25 Menu : 2 Menu:2 (Digital) 1280 × 1024 H : 8 0 . 0 K H z V : 7 5 . 0 H z Problem / Option Button to Press Adjustment Item Too soft Volume Direct Too loud NOTE is displayed while Mute is active.
-
Page 26: Screen Adjustments
ProLite E1702S / E1702SV / B1702S are designed to provide the best performance at resolution of 1280 × 1024, but can not provide the best at resolutions of less than 1280 × 1024 because the picture is automatically stretched to fit the full screen. - Page 27 C C C C C Press the Auto Button. (Auto Set-up) D D D D D Adjust the image manually by following procedure below when the screen has a flicker or blur, or the picture does not fit in the display area after performing the Auto Set-up.
- Page 28 G G G G G Adjust the Phase to correct horizontal wavy noise, flicker or blur in the zebra pattern. – NOTE In case the strong flicker or blurs remain on a part of the screen, repeat steps F and NOTE G because the Clock may not be adjusted correctly.
-
Page 29: Power Management Feature
POWER MANAGEMENT FEATURE The power management feature of this product complies with power saving requirement of E NERGY and VESA DPMS. When activated, it automatically reduces unnecessary power consumption ® of the monitor when your computer is not in use. To use the feature, the monitor needs to be connected to a VESA DPMS compliant computer. -
Page 30: Trouble Shooting
2. Consult the following items if you cannot find an appropriate adjustment item in OPERATING THE MONITOR or if the problem persists. If you are experiencing a problem which is not described below or you cannot correct the problem, discontinue using the monitor and contact your dealer or iiyama service center for further assistance. Problem... - Page 31 Problem Check No sound. The audio equipment (computer etc.) is ON. The Audio Cable is properly connected. The Volume is turned up. The Mute is OFF. The audio output level of the audio equipment is within the specification of the monitor. The sound is too The audio output level of the audio equipment is within the specification of loud or too quiet.
-
Page 32: Specifications: Prolite E1702S
1000 : 1 (Typical) Viewable angle Right / Left / Up / Down: 80 degrees each Response time ProLite E1702S-1: 5ms (Black, white, black), 2ms (Gray to Gray) ProLite E1702S-2: 5ms (Black, white, black) Display Colors Approx. 16.7 million maximum Sync Frequency Analog: Horizontal 24.0-80.0kHz, Vertical 55-75Hz... -
Page 33: Specifications: Prolite E1702Sv
SPECIFICATIONS: ProLite E1702SV LCD Panel a-Si TFT Active Matrix Driving system Size Diagonal: 43cm / 17" Pixel pitch 0.264mm H × 0.264mm V Brightness 300cd/m (Typical) Contrast ratio 1000 : 1 (Typical) Viewable angle Right / Left / Up / Down: 80 degrees each Response time ProLite E1702SV-1: 5ms (Black, white, black), 2ms (Gray to Gray) ProLite E1702SV-2: 5ms (Black, white, black) -
Page 34: Specifications: Prolite E1702Ws
SPECIFICATIONS: ProLite E1702WS LCD Panel a-Si TFT Active Matrix Driving system Size Diagonal: 43cm / 17" Pixel pitch 0.255mm H × 0.255mm V Brightness 250cd/m (Typical) Contrast ratio 600 : 1 (Typical) Viewable angle Right / Left: 80 degrees each, Up 85 degrees, Down: 65 degrees Response time 8ms (Black, white, black) Display Colors... -
Page 35: Specifications: Prolite E1702Wsv
SPECIFICATIONS: ProLite E1702WSV LCD Panel a-Si TFT Active Matrix Driving system Size Diagonal: 43cm / 17" Pixel pitch 0.255mm H × 0.255mm V Brightness 250cd/m (Typical) Contrast ratio 600 : 1 (Typical) Viewable angle Right / Left: 80 degrees each, Up 85 degrees, Down: 65 degrees Response time 8ms (Black, white, black) Display Colors... -
Page 36: Specifications: Prolite B1702S
SPECIFICATIONS: ProLite B1702S LCD Panel a-Si TFT Active Matrix Driving system Size Diagonal: 43cm / 17" Pixel pitch 0.264mm H × 0.264mm V Brightness 300cd/m (Typical) Contrast ratio 1000 : 1 (Typical) Viewable angle Right / Left / Up / Down: 80 degrees each Response time ProLite B1702S-1: 5ms (Black, white, black), 2ms (Gray to Gray) ProLite B1702S-2: 5ms (Black, white, black) -
Page 37: Dimensions : Prolite E1702S / E1702Sv
DIMENSIONS : ProLite E1702S / E1702SV 370.5mm/14.6" 59.5mm/2.3" 339.5mm/13.4" 204.0mm/8.0" DIMENSIONS : ProLite E1702WS / E1702WSV 400.5mm/15.8" 55.5mm/2.2" 368.5mm/14.5" 174.0mm/6.9" DIMENSIONS : ProLite B1702S 370.5mm/14.6" 59.5mm/2.3" 339.5mm/13.4" 300.5mm/11.8" ( ): Maximum adjustment range APPENDIX 33... -
Page 38: Compliant Timing
COMPLIANT TIMING Horizontal Vertical Video Mode Dot Clock Frequency Frequency 25.175MHz 31.469kHz 59.940Hz 37.500kHz 75.000Hz 31.500MHz 640 × 480 37.861kHz 72.809Hz 31.500MHz 35.156kHz 56.250Hz 36.000MHz 37.879kHz 60.317Hz 40.000MHz SVGA 800 × 600 49.500MHz 46.875kHz 75.000Hz VESA 50.000MHz 48.077kHz 72.188Hz 48.363kHz 60.004Hz 65.000MHz 1024 ×... -
Page 39: Connector Pin Assignment
CONNECTOR PIN ASSIGNMENT D-Sub mini 15pin Input Signal Input Signal Connector Red video Ground Green video Blue video Reserved port Data line (SDA)* Reserved port Ground Ground H-Sync Red video ground V-Sync Green video ground Clock line (SCL)* Blue video ground * Compliant to VESA DDC.
Need help?
Do you have a question about the ProLite E1702S and is the answer not in the manual?
Questions and answers