List Of Parts; Accessories; Assembling The Detector; Lower Shaft Assembly - Minelab Sovereign GT User Manual

2. list of parts

www.minelab.com
3. List of Parts
The box in which the Sovereign GT is shipped should contain the following items.
Please check that all of these items are in the box:
• Control Box
• 10" or 8" Round Tornado coil (inc. skid plate attached)
• 2-Piece Shaft Assembly (inc. Fiberglass lower shaft)
• Black Aluminium Armrest (inc. nuts & bolts) (2 part)
• Arm Rest Neoprene Cover
• Arm Rest Strap (2 part)
• Rear Control Box Bracket
• Battery Pack
• Velcro TM Straps (2 pair)
• Teardrop Washers (2)
• Nylon Nuts and Bolts
• Warranty Card
• Instruction Manual
Note: There may be variations to the items included in different countries so if you believe there may
be something missing, check with your dealer/supplier that it is standard issue.

4. Accessories

The following accessories are available to further improve your machine.
• Digital Target Identification Meter
• Alkaline Battery Holder ( holds 8 x 'AA' Batteries)
• NiMH rechargeable battery
• Mains Charger (240v/230v or 110v)
• 12V NiMH Vehicle Charger
• Headphones
• Hipmount Bag with Raincoat Protective Cover for Control Box
• Meter Protective Cover & hipmount Bag
• Padded Detector Transport Bag
• Minelab Padded Sleeveless Jacket
• Blue Minelab Polo Shirt
• Blue Minelab Cap
For further information on these and other Minelab products call your nearest
Authorised Minelab dealer.
p6
- See note

5. assembling the detector

5. Assembling the Detector
Please follow these instructions to assemble the Sovereign GT. Refer to the
drawings to identify parts and how they are positioned. Please contact your
Minelab dealer for further instructions should any difficulties arise.
5.

Lower Shaft Assembly

1.
a) Remove the tape on the lower fiberglass tube (3) that is
holding the black teardrop washers (12) in place.
Note: Ensure the washers do not fall out after removing the tape.
b) Remove the black nylon wing nut (11), and bolt (10) from
the coil (1).
c) With the teardrop washers in place, push the lower tube (3)
into the coil bracket so that the holes line up.
Note: Ensure that the black nylon spring clip near the top of
the fibreglass tube is pointing toward the rear of the coil.
d) Push the black nylon bolt (10) through the holes in the
bracket on the coil from the cable entry side and tighten
the wing nut (11) by hand.
5. Armrest/Upper Straight Shaft Assembly
2.
Note: In some countries the Sovereign GT is issued with an S-bend upper shaft and in
other countries it will have a straight shaft.
a) Slide the handle (5) onto the upper end of the upper shaft (4)
and push it on about a foot.
b) Place the two arm rest halves (6) on either side of the upper
shaft (4) and ensure that the bolt holes are aligned.
c) Slide the nylon bolts (10) through the bolt holes
and screw the nylon wing nuts (11) onto the bolts
with a couple of turns (do not tighten).
d) Slide the plastic control box bracket (9) into
the runners of the arm rest (6) & tighten the nylon
wing nuts by hand.
e) Attach the arm rest straps (8) using the
press studs on both sides of the arm rest.
f) Push the arm rest straps through the slots
in the arm rest cover (7) and push the cover
over the arm rest.
g) Position your arm into the arm rest and slide the
handle (5) along the shaft into a comfortable position.
Tighten the two screws in the base of the handle with a
small screwdriver.
If your detector is supplied with the S-bend shaft, assembly will be identical except that you
will not have to assemble the separate handle
www.minelab.com
Figure 1 - The coil and
lower shaft assembly
Figure 2 - Armrest/upper
shaft assembly
p7