Samsung SND-3080P User Manual
  1. Manuals
  2. Brands
  3. Samsung Manuals
  4. Security Camera
  5. SND-3080P
  6. User manual
Samsung SND-3080P User Manual

Samsung SND-3080P User Manual

Hide thumbs Also See for SND-3080P:
Table of Contents

Advertisement

Quick Links

NETWORK CAMERA

User Manual
SND-3080(P)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SND-3080P and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Samsung SND-3080P

Summary of Contents for Samsung SND-3080P

  • Page 1: Network Camera

    NETWORK CAMERA User Manual SND-3080(P)

  • Page 2: User Manual

    Samsung Techwin. Disclaimer Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. Samsung Techwin reserves the right to change the contents of this document without prior notice.
  • Page 3 overview CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit.
  • Page 4 Continued use in such a condition may cause fi re or electric shock. If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifi cations or attempted repair.) When cleaning, do not spray water directly onto parts of the product.
  • Page 5 CAUTION Do not drop objects on the product or apply strong blows to it. Keep away from a location subject to excessive vibration or magnetic interference. Do not install in a location subject to high temperature (over 50°C), low temperature (below -10°C), or high humidity.

  • Page 6: Fcc Statement

    overview FCC STATEMENT This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions : 1) This device may not cause harmful interference, and 2) This device must accept any interference received including interference that may cause undesired operation.

  • Page 7: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifi...

  • Page 8: Table Of Contents

    overview CONTENTS Important Safety Instructions OVERVIEW Product Features Recommended PC Specifi cations What’s Included At a Glance Removing the Covers INSTALLATION & Inserting/Removing an SD Memory CONNECTION Card Memory Card Information (Not Included) Connecting with Other Device Installation How to Use the Keyboard Controller CAMERA SETUP Main Menu Profi...
  • Page 9 Connecting to the Camera WEB VIEWER Login Installing Activex Using the Live Screen Backup Using the SD Search Viewer Screen SETUP SCREEN Accessing the Setup Screen Default Setup System Setup Overlay Setup Event Setup Network Setup Profi le APPENDIX Terminology Specifi...

  • Page 10: Overview 7

    overview PRODUCT FEATURES Support various communication protocols Supports TCP/IP, UDP, RTP/RTSP, SMTP for email, and FTP protocols as well as various internet protocols such as ARP, HTTP, HTTPS and DHCP. Web Browser-based Monitoring Using the Internet web browser to display the image in a local network environment. Automatic Local IP Setup Even a network novice can install it with minimum operations.

  • Page 11: What's Included

    WHAT’S INCLUDED Please check if your camera and accessories are all included in the product package. User Manual/ Camera Quick Guide IP INSTALLER DVD Test Monitor Cable Screw Dust-proof Plate  The Test Monitor Cable is connected to a portable displayer and used for testing the camera. If you intend to use it for an actual monitoring camera, use the BNC cable instead.

  • Page 12: At A Glance

    overview AT A GLANCE Appearance Item Description Dome Cover Case cover used to protect the lens and the main unit. Main Unit Consists of: lens, switch board, PCB and screws. Power Port Used to plug in the power cable. Used to connect the Video In connector of the monitor, from which the video Video Output Port signal of the camera outputs.
  • Page 13 Inside Item Description Alarm in/out terminals can be confi gured as follows: - ALARM IN : Terminal for Alarm Input. Alarm In / Out terminals - ALARM OUT : Terminal for Alarm Output. - GND : Grounding terminal. SD Memory Card Compartment for the SD memory card.
  • Page 14 overview Components Lens 14_ overview...
  • Page 15 Item Description Inner Cover Cover used to protect the main unit. Wing-Side Hook Tap on either end to remove the inner cover. The Test Monitor Cable is connected to a portable displayer and used for Monitor Out testing the camera. Zoom Lever Used to adjust or fix the zoom factor of the lens.

  • Page 16: Installation & Connection

    installation & connection REMOVING THE COVERS If you want to connect the Alarm I/O connectors, you must remove the dome cover and lens cover beforehand. Turn the dome cover counter-clockwise. Remove the dome cover by lifting it up. Tap on either end of the lens cover to remove it. 16_ installation &...

  • Page 17: Inserting/Removing An Sd Memory Card

    INSERTING/REMOVING AN SD MEMORY CARD Inserting an SD Memory Card Push the SD memory card in the direction of the arrow shown in the diagram.  Do not insert the SD memory card while it’s upside down by force. Otherwise, it may damage the SD memory card.

  • Page 18: Memory Card Information (Not Included)

    installation & connection MEMORY CARD INFORMATION (NOT INCLUDED) What is a memory card? The memory card is an external data storage device that has been developed to offer an entirely new way to record and share video, audio, and text data using digital devices. Selecting a memory card that’s suitable for you Your camera supports SDHC memory cards.

  • Page 19: Connecting With Other Device

    CONNECTING WITH OTHER DEVICE Power Monitor Network Power Supply Connect the power adaptor to the power input port.  Be careful not to reverse the polarity when you connect the power cable. You can also use a router featuring PoE (Power over Ethernet) to supply power to the camera. Connecting to the monitor Connect the [V_OUT] port of the camera to the video input port of the monitor.
  • Page 20 installation & connection Connecting to the I/O port box Connect the Alarm I/O cable to the corresponding port of the inner port box. ALARM IN ALARM OUT ALARM IN 1, 2 : Used to connect the alarm input signal. GND : Used for earth-grounding. ALARM OUT 1, 2 : Used to connect the alarm output signal.

  • Page 21: Installation

    INSTALLATION Precautions before installation Ensure you read the following instructions before installing the camera: Select an installation site (ceiling or wall) that can endure at least 5 times of the camera weight. Stuck-in or peeled-off cables can cause damage to the product or a fire. For safety purposes, keep anyone else away from the installation site.
  • Page 22 installation & connection Use the provided screws (x3) to fi x the bracket to a desired position (ceiling or wall).  Ensure that the <CAMERA FRONT> label on the bracket faces the direction for camera monitoring. Wiring Cover Arrange the cables through the bracket to the ceiling or wall. If you drill a hole in the ceiling cover for wiring, press hard to remove the cover and attach the dust-proof plate to it, and arrange the cables through the plate.

  • Page 23: Adjusting The Zoom And Focus

    Adjusting the monitoring direction for the camera Panning Tilt Adjustment Screw Tilting Lens rotation You can adjust the camera direction only when the camera is fixed on the ceiling. Then, turning the camera to the left or right is referred to as "Panning", while tilting the angle is "Tilting".

  • Page 24: Camera Setup

    camera setup You can configure the camera settings using the Web Viewer.  For accessing the Web Viewer, refer to "Network Connection and Setup". (page 34) HOW TO USE THE KEYBOARD CONTROLLER Follow the steps below if you run the Web Viewer for setting the menus. Launch the Web Viewer.

  • Page 25: Main Menu

    MAIN MENU You can configure the camera settings to your preference. PROFILE MAIN MENU MAIN MENU You can select a mode that is appropriate to the PROFILE camera installation environment. CAMERA SET CAMERA SET PRIVACY ZONE PRIVACY ZONE CAMERA SET OTHER SET OTHER SET SYSTEM INFO...

  • Page 26: Camera Setup

    camera setup CAMERA SETUP You can configure the general settings of the camera module. Use the four direction ( ▲▼◄ ► ) buttons to select a desired item. CAMERA ID Provide the ID and position for a camera that displays on the screen. For selecting and saving each menu item, refer to "How to use the keyboard controller".
  • Page 27 MOTION You can specify a level of AGC for controlling the CAMERA SET ◄ ► camera motion. Select F.FAST if you want to monitor a very fast CAMERA ID CAMERA ID IRIS IRIS moving object in a low contrast scene, and S.SLOW MOTION MOTION (F.FAST)
  • Page 28 camera setup DAY/NIGHT You can specify a recording mode according to the scene. For selecting and saving each menu item, refer to "How to use the keyboard controller". (page 24) Select <CAMERA SET> - <DAY/NIGHT>. AUTO AUTO Select a screen transition mode according to BURST the illumination, and set options as appropriate.

  • Page 29: White Bal

    WHITE BAL If you need to adjust the screen brightness, use the WHITE BALANCE function. For selecting and saving each menu item, refer to "How to use the keyboard controller". (page 24) Select <CAMERA SET> - <WHITE BAL>. WHITE BAL WHITE BAL Select a mode where you set the balance.
  • Page 30 camera setup AGC COLOR SUP This will adjust the color scheme according to the AGC value. REVERSE This will reverse the signal left to right, top to bottom, or a combination of the preceding. POSI/NEGA This will display the video brightness signal either normally or reversely. You can view a main image with a sub image on the same screen.

  • Page 31: Privacy Zone

    PRIVACY ZONE You can set up to 12 privacy zones that will be hided for privacy of the subject when recording. For selecting and saving each menu item, refer to "How to use the keyboard controller". (page 24) ZONE SETUP Select <MAIN MENU>...

  • Page 32: Others

    camera setup OTHERS You can reset the camera, or select the OSD font color to your preference. For selecting and saving each menu item, refer to "How to use the keyboard controller". (page 24) LANGUAGE You can slect a preferred language for the screen OTHER SET ◄...

  • Page 33: System Info

    SYSTEM INFO You can check the system information. For selecting and saving each menu item, refer to "How to use the keyboard controller". (page 24) Select <MAIN MENU> - <SYSTEM INFO>. SYSTEM INFO ◄ ► The current system information is displayed. TYPE TYPE 3_IPV_N...

  • Page 34: Network Connection And Setup

    You can set up the network settings according to your network configurations.  Before installing or while using this program, visit the Samsung website www.samsungsecurity.com and download and upgrade with the latest S/W version available. CONNECTING THE CAMERA TO AN IP ROUTER WITH THE XDSL/CABLE MODEM This is for a small network environment such as homes, SOHO and ordinary shops.
  • Page 35 ex3) If the address (LAN IP) of the IP router is 192.168.xxx.1 IP address: 192.168.xxx.100 Subnet Mask: 255.255.255.0 Default Gateway: 192.168.xxx.1  For the address of the IP router, refer to the product’s documentation. Checking if the IP router is connected to the xDSL/Cable modem properly Select <Status>...

  • Page 36: Connecting The Camera Directly To A

    network connection and setup Follow the instructions below if you select <Use the following IP address>: ex1) If the address (LAN IP) of the IP router is 192.168.1.1 IP address: 192.168.1.100 Subnet Mask: 255.255.255.0 Default Gateway: 192.168.1.1 ex2) If the address (LAN IP) of the IP router is 192.168.0.1 IP address: 192.168.0.100 Subnet Mask: 255.255.255.0 Default Gateway: 192.168.0.1...

  • Page 37: Connecting The Camera Directly To Local Area Networking

    When the IP Router is connected, the login window appears and prompts you to enter the password.  For the login IP and the password, refer to the IP router’s documentation. When done, you will see the setup window of the IP router. In the setup menu, select “Automatic Confi...

  • Page 38: Buttons Used In Ip Installer

    network connection and setup BUTTONS USED IN IP INSTALLER Item Description Model name of the connected camera. Device Name Click the column to sort the list by model name. However, search will be stopped if clicked during the search. Displays either <Static> or <Dynamic> for the current network connection Mode status.

  • Page 39: Static Ip Setup

    Item Description DDNS URL address enabling access from the external Internet. However, this will be replaced with the <IP Address> of the camera if DDNS registration has failed. IPv4 Scans for cameras with the IPv4 setting. IPv6 Scans for cameras with the IPv6 setting. Scans for cameras that are currently connected to the network.
  • Page 40 network connection and setup If using an IP router : IP Address : Enter an address falling in the IP range provided by the IP router. ex) 192.168.1.2~254, 192.168.0.2~254, 192.168.XXX.2~254 Subnet Mask : The <Subnet Mask> of the IP router will be the <Subnet Mask> of the camera.

  • Page 41: Auto Network Setup

    Click [OK]. Manual network setup will be completed. When the manual setup including <IP> is completed, the camera will restart. If the IP router has more than one camera connected Configure the IP related settings and the Port related settings distinctly with each other. Category Camera #1 Camera #2...

  • Page 42: Dynamic Ip Setup

    network connection and setup Enter the password. This is the login password for the "admin" user who accesses the camera. The default password is "4321". Click [OK]. Auto network setup will be completed. The camera will automatically complete the network setting and restart. DYNAMIC IP SETUP Dynamic IP Environment Setup Example of the dynamic IP environment...

  • Page 43: Port Range Forward (Port Mapping) Setup

    PORT RANGE FORWARD (PORT MAPPING) SETUP If you have installed an IP router with a camera connected, you must set the port range forwarding on the IP router so that a remote PC can access the camera in it. Manual Port Range Forwarding From the Setup menu of the IP router, select <Applications &...

  • Page 44: Connecting To The Camera From A Shared Local Pc

    network connection and setup CONNECTING TO THE CAMERA FROM A SHARED LOCAL Launch <IP Installer>. It will scan for connected cameras and display a list of them. Double-click a camera to access. The Internet browser starts and connects to the camera. ...

  • Page 45: Web Viewer

    web viewer CONNECTING TO THE CAMERA Normally, you would Launch the Internet browser. Type the IP address of the camera in the address bar. ex) • IP address (IPv4) : 192.168.1.200 http://192.168.1.200 - the Login dialog should appear. • IP address (IPv6) : 2001:230:abcd: ffff:0000:0000:ffff:1111 http://[2001:230:abcd:ffff:0000 :0000:ffff:1111]...

  • Page 46: Login

    web viewer To check the DDNS address The DDNS address consists of: <one of the lower-case letters: c, m, p> + <the last 6 digits of the MAC (Ethernet) address> + <websamsung.net> The small letter will be <c> if the first 6 digits of the MAC (Ethernet) address is <00:00:f0>, or <m>...

  • Page 47: Installing Activex

    INSTALLING ACTIVEX If connecting to a camera for the first time, you will see the installation message. Then, install the required ActiveX to access the camera and control the video from it in real time. For Windows XP Service Pack 2 users Click the installation message that pops up when you fi...

  • Page 48: Using The Live Screen

    web viewer USING THE LIVE SCREEN Item Description SD search Moves to the screen for searching event images from the SD card. Setup Move to the Setup screen. About You can check the firmware version, serial number and manufacturer information. Reset Alarm Resets the Alarm icon.

  • Page 49: Backup

    Samsung\SND-3080\SnapShot\Live If you want to change the path, click [Set path ( )] and specify a path. Windows Vista, Windows 7 : C:\users\[UserID]\Documents\Samsung\ SND-3080\SnapShot\Live On the Windows Vista, Windows 7 system, the path to save is fi xed. The screenshot fi le will be named automatically in the format of <IP address_ Port number_YYYYMMDD_hhmmss_index>.
  • Page 50 If you want to change the path, click [Set path ( )] and specify a path. Windows Vista, Windows 7 : C:\users\[UserID]\Documents\Samsung\ SND-3080\VideoClip\Live On the Windows Vista, Windows 7 system, the path to save is fi xed. The screenshot fi le will be named automatically in the format of <IP address_ Port number_YYYYMMDD_hhmmss_index>.

  • Page 51: Using The Sd Search Viewer Screen

    USING THE SD SEARCH VIEWER SCREEN Click <SD search> tab in the Live screen. The SD Search Screen appears. Name Function and description Thumbnail Size The thumbnail images are displayed based on the selected size. Date You can select the desired date to search for events generated. Schedule You can select the desired time to search the schedule events.

  • Page 52: Setup Screen

    setup screen ACCESSING THE SETUP SCREEN You can configure the default setting, system, overlay, event and network related settings, and change them as necessary. In the Live screen, click the <Setup> tab. The Setup screen appears. 52_ setup screen...

  • Page 53: Default Setup

    DEFAULT SETUP To configure the video settings You can set the video resolution and quality, and select the codec required. Select <Basic> - <Video>. The Video setup screen appears. Brightness : Adjust the screen brightness from 1 to 100. Contrast : Adjust the contrast from 1 to 100.
  • Page 54 setup screen Profi le : Select Baseline or Main for the H.264 profi ling method. Entropy coding* : Reduces the compression loss due to encoding. Motion estimation : Estimates the movement of pixels by determining the motion vector.  If you set the profi le to Baseline, the entropy coding is available only for CAVLC*; if you set it to MAIN, the entropy coding is available for both CAVLC* and CABAC*.
  • Page 55 IPv6 confi guration : Obtains the IPv6 address to access the IPv6 network. VNP confi guration : Set a port used to transfer video signals with the Samsung protocols. Device port (TCP) : Used to control the video signal transfer, defaulted to 60001(TCP).
  • Page 56 setup screen To set the user account Click <Basic> - <User>. The User setup window appears. Login authentication : You can set to authenticate the login by the user. If you select <Enable>, the user should have gone through the login authentication;...
  • Page 57 To edit a registered user account From the User setup window, select a user ID to change. From the User setup window, click [Modify]. The Modify user window appears. Change the <User ID>, <Password>, <Confi rm password>, and <Level> as you wish.

  • Page 58: System Setup

    setup screen SYSTEM SETUP To set the date/time You can obtain the current system time from the NTP server or your PC for your time setting. Select <System> - <Date & Time>. The Date & Time setup window appears. If you select Manual, input the date and time manually.

  • Page 59: To Update The Software

    To check the log information Select <System> - <Log>. The Log information list appears. System log list : Shows the log information about the system changes along with time and IP address. User login : Shows the current login user to the camera. Video confi...

  • Page 60: To Reset The System

    setup screen  If the network is disconnected, the power supply fails, or the PC abnormally operates during the update, the system does not work at all. To reset the system Restart or reset the system if it does not work properly or causes a problem. Select <System>...

  • Page 61: Overlay Setup

    Install a public certifi cate : To install the certifi cate to camera, you need to type a certifi cate name (it can be arbitrarily assigned by user), certifi cate fi le issued from the authority and a key fi le. When done, click [Install]. If the certifi...

  • Page 62: Event Setup

    setup screen EVENT SETUP To set the event transfer function You can set the FTP/email server (SMTP) to transfer the alarm images present in the camera, in case an alarm event occurs. Select <Event> - <Transfer setup>. The Image transfer setup window appears. ...
  • Page 63 Upload path : You can specify the path of the FTP directory to which you will transfer an alarm image. You can specify the path by just typing </directory name> or <directory name> in this fi eld. If nothing is specifi ed, the path will be defaulted to the root directory of the FTP server.
  • Page 64 setup screen To test the email transfer Click [Test]. This will test if the image is transferred to the specified SMTP server properly. When the test on the SMTP server connection and transfer is done, a message of <( Verified )> will be displayed.
  • Page 65 To set an alarm image You can configure to send message via FTP/E-mail (SMTP) or to save recording into the SD memory card. Select a transfer method when an event occurs or the schedule transfer function is activated. Select <Event> - <Alarm image>. The Alarm Image setup window appears.
  • Page 66 setup screen To set the alarm input Select <Event> - <Alarm input 1> or <Alarm input 2>. The Alarm Input setup window appears. When done, click [Apply]. Your settings will be saved. Input device setup : Select an input type according to the characteristics of the alarm sensor on the rear of the camera.
  • Page 67 To set the motion detection function Select <Event> - <Motion>. The Motion Detection setup window appears. When done, click [Apply]. Your settings will be saved. M.D. function : If selecting <Enable>, the motion detection function will be activated; if selecting <Disable>, it will not operate at all.
  • Page 68 setup screen To set a motion area You can set a specific area to detect a motion in. From the Motion Detection setup window, click [Setup] in the <Motion area>. The Motion Area window appears. You can set a specifi c area to detect a motion in.

  • Page 69: Network Setup

    When done, click [Apply]. Your settings will be saved. VNP streaming : You can set the Samsung Protocol (VNP) for the streaming service. Protocol : Select a video transfer protocol from TCP*, UDP (Unicast)*, and UDP (Multicast)*.  Multicast backbone (MBone) is not supported; you can access the camera only in the multicast local network environment.

  • Page 70: Appendix

    appendix PROFILE CAMERA SETUP MENU STANDARD BACKLIGHT DAY/NIGHT GAMING BANK Parent Menu Sub-menus IRIS LENS LEVEL BACKLIGHT (F.FAST) (F.FAST) (F.FAST) (F.FAST) MOTION NORM SLOW SHUTTER AUTO 1/250 SENSE UP AUTO X4 AUTO X2 AUTO X4 AUTO X4 AUTO X4 AUTO X4 AUTO AUTO AUTO...

  • Page 71: Terminology

    TERMINOLOGY GOP : The default is 15, and if set to 15, one I-Frame will be output per 15 frames as one I-Frame and 14 P-Frames constitute the GOP. The lower the GOP size is, the better the quality is; however, the bit rate as well as the data size will increase, causing a lower of the fps.

  • Page 72: Specifications

    appendix SPECIFICATIONS Description Item NTSC Camera Color/BW Color Type Device 1/3" Super-HAD PS CCD Image Total 811 x 508 795 x 596 Pixels Effective 768 x 494 752 x 582 System Progressive Scanning Horizontal Frequency 15.734 Hz 15.625 Hz Vertical Frequency 59.94 Hz 50 Hz Sens off : 0.12 Lux(15 IRE), 0.2 Lux(30 IRE),...
  • Page 73 Description Item NTSC Horizontal 600 TV Lines Resolution Vertical 350 TV Lines Video Output Video Output VBS 1.0Vp-p S/N Ratio S/N Ratio about 52 dB Lens Drive Type AI (DC) Lens Mount Type Board Type Embedded Linux Flash memory 32M byte 256M byte Network Board...
  • Page 74 Internet Explorer 6.0 or Higher Browser Viewer UI Language E/F/G/S/I/C/K (Default) S/W upgrade Support Video Player RTP/RTSP streaming Quicktime, VLC player Video Samsung iPOLiS Management 3rd Party S/W appliction Software Application IP Installation IP Installer Application for All Samsung IP Devices 74_ appendix...
  • Page 75 Description Item NTSC Provides functionality to control cameras and set/retrieve internal parameter values. HTTP API CGI Command Get JPEG image or MJPEG stream Alarm In/Out control RTP/RTSP API RTP Header, RTSP Command Document ActiveX ActiveX API for viewing data streams from IP camera. AC24V±10%(60Hz±0.3Hz)/ DC12V+10%/-5% / Power PoE (Power over Ethernet)

  • Page 76: Frame Rate (Ntsc)

    appendix FRAME RATE (NTSC)  Test Condition: MJPEG - Resolution(CIF), Quality(1), Frame rate(1) H.264 - Bitrate control(CBR), Compression(40), Encode Priority(Frame rate), GOP size(15), Deblock(ON), Profi le(Baseline), Entropy coding(CAVLC), Motion estimation(HPel) MPEG4 - Bitrate control(CBR), Compression(40), Encode Priority(Frame rate), De-Interlace(ON), GOP size(15) ❖...
  • Page 77 ❖ H.264 (4CIF) Frame Rate 30 FPS 15 FPS 8 FPS 3 FPS 1 FPS Quality 2298 Kbps 1229 Kbps 737 Kbps 369 Kbps 147 Kbps LEVEL10 19 FPS 10 FPS 6 FPS 3 FPS 1 FPS 1751 Kbps 1198 Kbps 645 Kbps 369 Kbps 111 Kbps...
  • Page 78 appendix ❖ MPEG4 (VGA) Frame Rate 30 FPS 15 FPS 8 FPS 3 FPS 1 FPS Quality 4055 Kbps 2580 Kbps 1290 Kbps 737 Kbps 221 Kbps LEVEL10 22 FPS 14 FPS 7 FPS 4 FPS 1 FPS 3533 Kbps 2304 Kbps 1075 Kbps 614 Kbps...
  • Page 79 ❖ H.264 (VGA) Frame Rate 30 FPS 15 FPS 8 FPS 3 FPS 1 FPS Quality 2089 Kbps 1229 Kbps 737 Kbps 369 Kbps 147 Kbps LEVEL10 17 FPS 10 FPS 6 FPS 3 FPS 1 FPS 1659 Kbps 1014 Kbps 553 Kbps 276 Kbps 111 Kbps...
  • Page 80 appendix ❖ MPEG4 (CIF) Frame Rate 30 FPS 15 FPS 8 FPS 3 FPS 1 FPS Quality 1382 Kbps 691 Kbps 369 Kbps 184 Kbps 55 Kbps LEVEL10 30 FPS 15 FPS 8 FPS 4 FPS 1 FPS 1152 Kbps 576 Kbps 307 Kbps 154 Kbps...
  • Page 81 ❖ H.264 (CIF) Frame Rate 30 FPS 15 FPS 8 FPS 3 FPS 1 FPS Quality 922 Kbps 461 Kbps 215 Kbps 123 Kbps 37 Kbps LEVEL10 30 FPS 15 FPS 7 FPS 4 FPS 1 FPS 691 Kbps 346 Kbps 184 Kbps 92 Kbps 28 Kbps...

  • Page 82: Frame Rate (Pal)

    appendix FRAME RATE (PAL)  Test Condition: MJPEG - Resolution(CIF), Quality(1), Frame rate(1) H.264 - Bitrate control(CBR), Compression(40), Encode Priority(Frame rate), GOP size(15), Deblock(ON), Profi le(Baseline), Entropy coding(CAVLC), Motion estimation(HPel) MPEG4 - Bitrate control(CBR), Compression(40), Encode Priority(Frame rate), De-Interlace(ON), GOP size(15) ❖...
  • Page 83 ❖ H.264 (4CIF) Frame Rate 25 FPS 13 FPS 6 FPS 3 FPS 1 FPS Quality 2359 Kbps 1180 Kbps 737 Kbps 442 Kbps 147 Kbps LEVEL10 16 FPS 8 FPS 5 FPS 3 FPS 1 FPS 1991 Kbps 1106 Kbps 664 Kbps 332 Kbps 111 Kbps...
  • Page 84 appendix ❖ MPEG4 (VGA) Frame Rate 25 FPS 13 FPS 6 FPS 3 FPS 1 FPS Quality 4424 Kbps 2654 Kbps 1327 Kbps 664 Kbps 221 Kbps LEVEL10 20 FPS 12 FPS 6 FPS 3 FPS 1 FPS 3871 Kbps 2212 Kbps 1106 Kbps 553 Kbps...
  • Page 85 ❖ H.264 (VGA) Frame Rate 25 FPS 13 FPS 6 FPS 3 FPS 1 FPS Quality 2507 Kbps 1327 Kbps 737 Kbps 442 Kbps 147 Kbps LEVEL10 17 FPS 9 FPS 5 FPS 3 FPS 1 FPS 1991 Kbps 1217 Kbps 664 Kbps 332 Kbps 111 Kbps...
  • Page 86 appendix ❖ MPEG4 (CIF) Frame Rate 25 FPS 13 FPS 6 FPS 3 FPS 1 FPS Quality 1382 Kbps 664 Kbps 332 Kbps 166 Kbps 55 Kbps LEVEL10 25 FPS 12 FPS 6 FPS 3 FPS 1 FPS 1152 Kbps 553 Kbps 276 Kbps 138 Kbps...
  • Page 87 ❖ H.264 (CIF) Frame Rate 25 FPS 13 FPS 6 FPS 3 FPS 1 FPS Quality 922 Kbps 442 Kbps 221 Kbps 111 Kbps 37 Kbps LEVEL10 25 FPS 12 FPS 6 FPS 3 FPS 1 FPS 691 Kbps 332 Kbps 166 Kbps 83 Kbps 28 Kbps...

  • Page 88: Troubleshooting

    appendix TROUBLESHOOTING PROBLEM SOLUTION Check to make sure that the camera’s Network settings are appropriate. Check to make sure that all network cables have been connected properly. If connected using DHCP, verify that the camera is able to acquire I can’t access the camera from a dynamic IP addresses without any problem.
  • Page 89 PROBLEM SOLUTION Verify the settings in the following sequence: I enabled Motion Detection Feature A. NTP must be properly configured. under Motion Detection, but .jpg files are not getting sent over FTP/ B. Motion Detection Feature must be enabled. SMTP even after motion detection C.

  • Page 90: Gpl/Lgpl Software License

    You may obtain the complete Corresponding Source code from us for a period of three years after our last shipment of this product by sending email to help.cctv@samsung.com If you want to obtain the complete Corresponding Source code in the physical medium such as CD-ROM, the cost of physically performing source distribution might be charged.
  • Page 91 The "Program", below, refers to any such itself is interactive but does not normally print program or work, and a "work based on the such an announcement, your work based Program" means either the Program or any on the Program is not required to print an derivative work under copyright law : that is to announcement.) say, a work containing the Program or a portion...
  • Page 92 associated interface defi nition fi les, plus the scripts your obligations under this License and any other used to control compilation and installation of the pertinent obligations, then as a consequence you executable. However, as a special exception, the may not distribute the Program at all. source code distributed need not include anything For example, if a patent license would not permit that is normally distributed (in either source or...

  • Page 93: End Of Terms And Conditions

    for permission. For software which is copyrighted of warranty ; and each fi le should have at least the by the Free Software Foundation,write to the "copyright" line and a pointer to where the full notice Free Software Foundation ; we sometimes make is found.

  • Page 94: Gnu General Public License

    consider it more useful to permit linking proprietary clearly explains that there is no warranty for this free applications with the library. If this is what you want software. For both users' and authors' sake, the to do, use the GNU Lesser General Public License GPL requires that modifi...
  • Page 95 copyright law, except executing it on a computer shared libraries and dynamically linked subprograms or modifying a private copy. Propagation includes that the work is specifi cally designed to require, such copying, distribution (with or without modifi cation), as by intimate data communication or control fl ow making available to the public, and in some countries between those subprograms and other parts of the other activities as well.
  • Page 96 means of enforcing, against the work's users, your work in an aggregate does not cause this License to or third parties' legal rights to forbid circumvention of apply to the other parts of the aggregate. technological measures. 6. Conveying Non-Source Forms. 4.
  • Page 97 Source of the work are being offered to the be in a format that is publicly documented (and with general public at no charge under subsection 6d. an implementation available to the public in source code form), and must require no special password or A separable portion of the object code, whose source key for unpacking, reading or copying.
  • Page 98 All other non-permissive additional terms are considered However, nothing other than this License grants you “further restrictions” within the meaning of section permission to propagate or modify any covered work. 10. If the Program as you received it, or any part of These actions infringe copyright if you do not accept it, contains a notice stating that it is governed by this this License.
  • Page 99 sell, offer for sale, import and otherwise run, modify arrangement, or that patent license was and propagate the contents of its contributor version. granted, prior to 28 March 2007. In the following three paragraphs, a “patent license” Nothing in this License shall be construed as is any express agreement or commitment, however excluding or limiting any implied license or other denominated, not to enforce a patent (such as an...

  • Page 100: Gnu Lesser General Public License

    Later license versions may give you additional USA Everyone is permitted to copy and distribute or different permissions. However, no additional verbatim copies of this license document, but obligations are imposed on any author or copyright changing it is not allowed. holder as a result of your choosing to follow a later [This is the fi...
  • Page 101 if the library is modifi ed by someone else and passed Although the Lesser General Public License is Less on, the recipients should know that what they have is protective of the users’ freedom, it does ensure that not the original version, so that the original author’s the user of a program that is linked with the Library reputation will not be affected by problems that might has the freedom and the wherewithal to run that...
  • Page 102 any medium, provided that you conspicuously and In addition, mere aggregation of another work not appropriately publish on each copy an appropriate based on the Library with the Library (or with a work copyright notice and disclaimer of warranty; keep based on the Library) on a volume of a storage or intact all the notices that refer to this License and distribution medium does not bring the other work...
  • Page 103 When a “work that uses the Library” uses material (1) uses at run time a copy of the library already from a header fi le that is part of the Library, the present on the user’s computer system, rather object code for the work may be a derivative work than copying library functions into the executable, of the Library even though the source code is not.
  • Page 104 8. You may not copy, modify, sublicense, link with, or software distribution system which is implemented by public license practices. Many people have distribute the Library except as expressly provided under this License. Any attempt otherwise to copy, made generous contributions to the wide range of software distributed through that system in reliance modify, sublicense, link with, or distribute the on consistent application of that system;...

  • Page 105: Openssl License

    PARTIES PROVIDE THE LIBRARY “AS IS” This library is distributed in the hope that it will be WITHOUT WARRANTY OF ANY KIND, EITHER useful, but WITHOUT ANY WARRANTY; without EXPRESSED OR IMPLIED, INCLUDING, BUT even the implied warranty of MERCHANTABILITY or NOT LIMITED TO, THE IMPLIED WARRANTIES FITNESS FOR A PARTICULAR PURPOSE.
  • Page 106 THIS SOFTWARE IS PROVIDED BY THE OpenSSL 3. All advertising materials mentioning features or PROJECT “AS IS” AND ANY EXPRESSED OR use of this software must display the following IMPLIED WARRANTIES, INCLUDING, BUT acknowledgement: “This product includes NOT LIMITED TO, THE IMPLIED WARRANTIES cryptographic software written by Eric Young (eay@ OF MERCHANTABILITY AND FITNESS FOR A cryptsoft.com)”...
  • Page 107 Samsung Techwin cares for the environment at all product manufacturing stages, and is taking measures to provide customers with more environmentally friendly products. The Eco mark represents Samsung Techwin’s devotion to creating environmentally friendly products, and indicates that the product satisfies the EU RoHS Directive.
  • Page 108 TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745 SAMSUNG TECHWIN AMERICA Inc. SAMSUNG TECHWIN EUROPE LTD. 1480 Charles Willard St, Carson, CA 90746, UNITED STATES Samsung House, 1000 Hillswood Drive, Hillswood Business Tol Free : +1-877-213-1222 FAX : +1-310-632-2195 Park Chertsey, Surrey, UNITED KINGDOM KT16 OPS www.samsungcctvusa.com TEL : +44-1932-45-5300 FAX : +44-1932-45-5325 www.samsungtechwin.com...

This manual is also suitable for:

Snd-3080Snd-3080c

Table of Contents