CONTENT 1. GENERAL 1.1 General 1.2 Characteristic 1.3 Composition 2. SPECIFICATION 2.1 General Specification 2.2 Electrical Specification 3. OPERATION 3.1 Drawings of the radio 3.2 ICONS on LCD 3.3 Key Functions 3.4 Setting and Operation 4. CHANNEL DATA (With Sub-Channel data)
C) CPU of this equipment is HD404889 from HITACHI. d) You can use PMR 446 and FM Radio with this unit at the same time. e) It's power can operate by use of ALCALINE 4 cell(1.5V AAA) battery 1.3 COMPOSITION...
3.2 ICONS on LCD 1. RSSI (Receiving Signal Strength Indicator) or TX Bar Icon Indicates the receiving signal strength during transmission and it can be indicated the number of bar according to the strength of receiving signal. 2) Monitor Indicator Appears when the monitor button is used.
12) Large Segment Display Indicates the channel number in use at the normal mode. When the Function Button is pressed, it Displays the function menu in sequence: Ch / rdo / Sc / Uo / H00 / Sub / CAL / bEP / rog / tAL / [1] / [2] / [3] / P1 / P2 / P3 / P4 / P5 13) Small Segment Display Displays the FM frequency at the FM mode.
Page 8
3.3-2 FUNCTION BUTTON (#12) 1) Short Touch Press this button briefly to enter function edit mode in standby mode. 2) Long Touch - Press for longer than 1.5 seconds to activate the KEY LOCK in the standby mode. Please note all buttons will be disabled except the Monitor Button (#2) and PTT Button (#4) will remain fully operational.
3.3-7 EXTERNAL MIC/SPEAKER (#6) - This jack accepts an optional headset/microphone for handsfree operation. - Please refer to the Albrecht catalogue or homepage to see the variety of available accessories. See also section regarding VOX SELECTION MODE. 3.4 Setting and Operation 3.4-1 CHANNEL SELECTION...
Page 10
2) CTCSS (Coded Tone Controlled Squelch System) SUB-CHANNEL SELECTION MODE This feature allows you to utilize a less used channel range (00-38) within a main channel. This enables you to communicate with another party on the same main channel using the same sub- code.
Page 11
3.4-3 CHANNEL SCAN MODE 1) NORMAL SCAN MODE This feature allows you to scan for an active channel and communicate with the party transmitting. The power saver is disabled in this mode. To access the Auto Channel Scan menu, Press the Function Button (#12) until the word “SC” appears in the LCD. - Press the Down Button (#11) or the Up Button (#10) to choose “nr”.
Page 12
3.4-4 VOX & VOX RECOVERY TIME SELECTION MODE 1) VOX SELECTION MODE The Voice Activated Transmission (VOX) function allows your voice to activate transmission automatically when the TECTALK FM is used with the optional Handsfree MIC/headset. It also allows Handsfree use when a MIC/headset is not being used without having to use the PTT Button (#4).
Page 13
3.4-6 SUB OPTION SELECTION MODE This mode allows you to enter the sub option selection mode. -Press the Function Button (#12) until the word “Sub” appears in the LCD. You can now select between “yes” or “No”. -If you press the Function Button (#12) when “yes” blinks on the LCD Panel (#8), you enter into the Sub Function edit menu.
Page 14
- Press Function Button (#12) at the CTCSS display option mode, You can select On or Off with Up(#10) or Down(#11) button. - When you press Enter Button (#13) or not press any key in 5 seconds, it returns back Stand-by mode with back beep sound after installation squelch tail elimination option its setting.
CTCSS (Continuous Tone Coded Squelch System) Frequency List Sub Channel Tone Frequency Sub Channel Tone Frequency 67.0 Hz 136.5 Hz 71.9 Hz 141.3 Hz 74.4 Hz 146.2 Hz 77.0 Hz 151.4 Hz 79.7 Hz 156.7 Hz 82.5 Hz 162.2 Hz 85.4 Hz 167.9 Hz 88.5 Hz...
Page 16
CE- Declaration of Conformity Albrecht Tectalk-FM / JDP-408 HF This unit complies to all relevant European Standards and Regulations for PMR 446 radio service. This radio may be used only in EU countries and some other states applying the R&TTE directive of the European Community.
Need help?
Do you have a question about the PMR 446 and is the answer not in the manual?
Questions and answers