Assembly And Setup; P-Series Upright Bike Assembly And Setup - STAR TRAC FITNESS P-UB Owner's Manual

A
SSEMBLY AND

P-SERIES UPRIGHT BIKE ASSEMBLY AND SETUP

Use the following procedures to unpack and assemble your STAR TRAC P-SERIES UPRIGHT BIKE.
U
NPACKING
Open the shipping carton, remove all parts from the carton and foam inserts, and verify that the following parts are included in your ship-
ment:
Bike Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Display Console Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 1
Seat Post Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Front Foot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Rear Foot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Pedals (set of two) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Screw, Button Head, M10 X 30 . . . . . . . . . . . . . . . . . . . . . 8
Screw, Flat Head, M6 X 16 . . . . . . . . . . . . . . . . . . . . . . . . 4
Take time now to enter your P-SERIES Bike serial number in the space below. If parts are missing, or if you have any operational ques-
tions, please call Star Trac's Service Department at (800) 503-1221; have your serial number ready.
Serial No. ___________________________
A
SSEMBLY
The front foot assembly has wheels attached to the front edge.
Be sure the wheels face forward when installing the front foot assem-
bly.
Stand the bike frame upright and place the front foot assembly under
the frame, aligning the holes in the foot with the holes in the frame.
Using the 6mm hex wrench and four M10 X 30 button head screws,
secure the front foot assembly to the frame. Tighten all four screws
securely.
Be sure the rear foot assembly is positioned with the curved
edge facing forward (similar to the front foot).
Lift up the rear of the bike frame and place the rear foot assembly in
position under the frame, aligning the holes in the foot with the holes
in the frame.
Using the 6mm hex wrench and four M10 X 30 button head screws,
secure the rear foot assembly to the frame. Tighten all four screws
securely.
STAR TRAC P-SERIES BIKES O
S
ETUP
' G
WNER S UIDE
Screw, Socket Head, M6 X 10 with Star Washer . . . . . . . . 1
Screw, Socket Head, M4 X 20 . . . . . . . . . . . . . . . . . . . . . . 2
Wrench, Hex, 6mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Wrench, Hex, 5mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Wrench, Hex, 4mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Multi-end Wrench, 10mm, 12mm, 15mm . . . . . . . . . . . . . . 1
Wrench, Hex, 3mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
11