Table of Contents
Advertisement
TOOL STICKERS & TAGS
Failure to use hydraulic hose labeled and
certified as non-conductive when using
hydraulic tools on or near electric lines
may result in death or serious injury.
ELECTROCUTION
HAZARD
17160
Electrical Danger Decal
Staney Hydraulic Tools
3810 SE Naef Road
Miwaukie, OR 97267
HD08
Model No.:
CAUTION
15-34 LPM/4-9 GPM
DO NOT EXCEED 140 BAR/2000 PSI
DO NOT EXCEED SPECIFIED FLOW OR PRESSURE.
CLOSED-CENTER TOOL ON CLOSED-CENTER SYSTEM.
USE OPEN-CENTER TOOL ON OPEN-CENTER SYSTEM.
CORRECTLY CONNECT HOSES TO TOOL "IN" AND "OUT"
PORTS.
IMPROPER HANDLING, USE OR MAINTENANCE OF
TOOL COULD RESULT IN A LEAK, BURST OR OTHER
TOOL FAILURE.
CONTACT AT A LEAK OR BURST CAN
CAUSE OIL INJECTION INTO THE BODY.
FAILURE TO
OBSERVE THESE PRECAUTIONS CAN RESULT IN SERIOUS
PERSONAL INJURY.
17161
HD08 Name Tag/GPM Decal
C
C
C
17162
OC/CC Decal
Note:
THE INFORMATION LISTED
ON THE STICKERS SHOWN,
MUST BE LEGIBLE AT ALL
TIMES.
REPLACE DECALS IF
THEY BECOME WORN OR
DAMAGED. REPLACEMENTS
ARE AVAILABLE FROM
YOUR LOCAL STANLEY
DISTRIBUTOR.
The safety tag (P/N 15875) at right is
attached to the tool when shipped from
the factory. Read and understand the
safety instructions listed on this tag before
removal. We suggest you retain this tag and
attach it to the tool when not in use.
6 ► HD08 user manual
For proper and safe operation read
owners manual and make sure that you
have been properly trained in correct
17179
procedures required for work on or
around electric lines.
Stanley Decal
11354
USE
OC/CC Decal
30 LPM @ 138 B AR
EHTMA CATEGORY
11207
Circuit D Decal
1.
2.
SAFETY TAG P/N 15875 (Shown smaller then actual size)
Stanley Hydraulic Tools
3810 SE Naef Road
Milwaukie, OR 97267
D
11206
Circuit C Decal
d a N G e r
FAILURE TO USE HYDRAULIC HOSE LABELED AND CER-
TIFIED AS NON-CONDUCTIVE WHEN USING HYDRAULIC
TOOLS ON OR NEAR ELECTRICAL LINES MAY RESULT IN
DEATH OR SERIOUS INJURY.
BEFORE USING HOSE laBeled aNd certiFied aS NoN-
coNductiVe ON OR NEAR ELECTRIC LINES BE SURE THE
HOSE IS maiNtaiNed aS NoN-coNductiVe. THE HOSE
SHOULD BE REGULARLY TESTED FOR ELECTRIC CUR-
RENT LEAKAGE IN ACCORDANCE WITH YOUR SAFETY
DEPARTMENT INSTRUCTIONS.
A HYDRAULIC LEAK OR BURST MAY CAUSE OIL INJEC-
TION INTO THE BODY OR CAUSE OTHER SEVERE
PERSONAL INJURY.
A.
do Not EXCEED SPECIFIED FLOW AND PRESSURE
FOR THIS TOOL. EXCESS FLOW OR PRESSURE MAY
CAUSE A LEAK OR BURST.
B.
do Not EXCEED RATED WORKING PRESSURE OF
HYDRAULIC HOSE USED WITH THIS TOOL. EXCESS
PRESSURE MAY CAUSE A LEAK OR BURST.
C.
CHECK TOOL HOSE COUPLERS AND CONNECTORS
DAILY FOR LEAKS. do Not FEEL FOR LEAKS WITH
YOUR HANDS. CONTACT WITH A LEAK MAY RESULT
IN SEVERE PERSONAL INJURY.
i m P o r t a N t
read oPeratioN maNual aNd
SaFety iNStructioNS For tHiS
TOOL BEFORE USING IT.
uSe oNly PartS aNd rePair
ProcedureS aPProVed By
StaNley aNd deScriBed iN tHe
OPERATION MANUAL.
taG to Be remoVed oNly By
TOOL OPERATOR.
See otHer Side
28323
CE Decal
28788
Manual Decal
22796
Sound Power Level Decal
d a N G e r
D.
DO NOT LIFT OR CARRY TOOL BY THE HOSES. DO
NOT ABUSE HOSE. DO NOT USE KINKED, TORN OR
DAMAGED HOSE.
3.
MAKE SURE HYDRAULIC HOSES ARE PROPERLY CON-
NECTED TO THE TOOL BEFORE PRESSURING SYSTEM.
SYSTEM PRESSURE HOSE MUST ALWAYS BE CON-
NECTED TO TOOL "IN" PORT. SYSTEM RETURN HOSE
MUST ALWAYS BE CONNECTED TO TOOL "OUT" PORT.
REVERSING CONNECTIONS MAY CAUSE REVERSE
TOOL OPERATION WHICH CAN RESULT IN SEVERE
PERSONAL INJURY.
4.
DO NOT CONNECT OPEN-CENTER TOOLS TO CLOSED-
CENTER HYDRAULIC SYSTEMS. THIS MAY RESULT IN
LOSS OF OTHER HYDRAULIC FUNCTIONS POWERED BY
THE SAME SYSTEM AND/OR SEVERE PERSONAL INJURY.
5.
BYSTANDERS MAY BE INJURED IN YOUR WORK AREA.
KEEP BYSTANDERS CLEAR OF YOUR WORK AREA.
6.
WEAR HEARING, EYE, FOOT, HAND AND HEAD PRO-
TECTION.
7.
TO AVOID PERSONAL INJURY OR EQUIPMENT DAMAGE,
ALL TOOL REPAIR MAINTENANCE AND SERVICE MUST
ONLY BE PERFORMED BY AUTHORIZED AND PROPERLY
TRAINED PERSONNEL.
i m P o r t a N t
read oPeratioN maNual aNd
SaFety iNStructioNS For tHiS
TOOL BEFORE USING IT.
uSe oNly PartS aNd rePair
ProcedureS aPProVed By
StaNley aNd deScriBed iN tHe
OPERATION MANUAL.
taG to Be remoVed oNly By
TOOL OPERATOR.
See otHer Side
Advertisement
Table of Contents
