Stanley HD45 User Manual
Hydraulic hammer drill
Hide thumbs
Also See for HD45:
- Service manual (24 pages) ,
- User manual (24 pages) ,
- User manual (12 pages)
Subscribe to Our Youtube Channel
Related Manuals for Stanley HD45
Summary of Contents for Stanley HD45
- Page 1 HD45 HYDRAULIC HAMMER DRILL USER MANUAL Safety, Operation and Maintenance © 2014 Stanley Black & Decker, Inc. New Britain, CT 06053 U.S.A. 66301 2/2015 Ver. 8...
-
Page 2: Declaration Of Conformity
Provisiones especiales: Disposizioni speciali: Representative in the Union: Patrick Vervier, Stanley Dubuis 17-19, rue Jules Berthonneau-BP 3406 41034 Blois Cedex, France. Vertreter in der Union/Représentant dans l’union/Representante en la Union/Rappresentante presso l’Unione Done at/Ort/Fait à/Dado en/Fatto a Stanley Hydraulic Tools, Milwaukie, Oregon USA... -
Page 3: Table Of Contents
REPAIRS AND / OR SERVICE TO THIS TOOL MUST ONLY BE DONE BY AN AUTHORIZED AND CERTIFIED DEALER. For the nearest authorized and certified dealer, call Stanley Hydraulic Tools at the number listed on the back of this manual and ask for a Customer Service Representative. -
Page 4: Safety Symbols
Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULATIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel. 4 ► HD45 User Manual... -
Page 5: Safety Precautions
• When working near electrical conductors, always The model HD45 Hydraulic Hammer Drill will provide assume that all conductors are energized and that safe and dependable service if operated in accordance insulation, clothing and hoses can conduct electric- with the instructions given in this manual. -
Page 6: Tool Stickers & Tags
OPERATION MANUAL. OPERATION MANUAL. TAG TO BE REMOVED ONLY BY TAG TO BE REMOVED ONLY BY TOOL OPERATOR. TOOL OPERATOR. SEE OTHER SIDE SEE OTHER SIDE SAFETY TAG P/N 15875 (shown smaller then actual size) 6 ► HD45 User Manual... -
Page 7: Hose Types
HOSE SAFETY TAGS To help ensure your safety, the following DANGER tags are attached to all hose purchased from Stanley Hydraulic Tools. DO NOT REMOVE THESE TAGS. -
Page 8: Hose Recommendations
HOSE RECOMMENDATIONS 8 ► HD45 User Manual... -
Page 9: Htma Requirements
2000 psi 2000 psi 2000 psi (at the power supply outlet) (172 bar) (138 bar) (138 bar) (138 bar) (138 bar) NOTE: These are general hydraulic system requirements. See tool specification page for tool specific requirements HD45 User Manual ◄ 9... -
Page 10: Operation
NOTE: If uncoupled hoses are left in the sun, pres sure in- crease within the hoses can make them difficult to connect. Whenever possible, connect the free ends of hoses together. 10 ► HD45 User Manual... -
Page 11: Cold Weather Operation
2. Spray oil into the On/Off valve trigger slot area. 3. Dip or spray the entire tool. 4. Cycle the tool hydraulically several times before storing away. HD45 User Manual ◄ 11... -
Page 12: Charging The Accumulator
2. Connect the chuck of the charging assembly to the charging valve on the accumulator tester or, if pre- ferred, remove the tester from the charging valve and connect the charging assembly chuck directly to the charging valve. 12 ► HD45 User Manual... -
Page 13: Figure 2. Charging The Accumulator
CHARGING THE ACCUMULATOR Figure 2. Charging the Accumulator HD45 User Manual ◄ 13... -
Page 14: Tool Protection & Care
This can cause damage to internal seals. on the striking end. • Always replace hoses, couplings and other parts with replacement parts recommended by Stanley Hydraulic Tools. Supply hoses must have a mini- mum working pressure rating of 2500 psi/172 bar. •... -
Page 15: Troubleshooting
Continued operation or break in with mo- Motor not completely broken in. tor break-in block will correct. Low rotation torque. Damage to motor clearances. Repair as required. Mechanical binding during drilling. Take care to guide drill straight. HD45 User Manual ◄ 15... -
Page 16: Specifications
Flow Sleeve Removal Tool ..........................04919 Bearing Installation Tool ............................05044 Latch Removal Tool ............................05045 Bearing Installation Tool ............................05061 Latch Installation Tool ............................05062 Accumulator Cylinder Puller ..........................05640 Seal Kit ................................05839 Latch Installation Tool ............................05879 Accumulator Charge Kit.............................31254 16 ► HD45 User Manual... -
Page 17: Hd45 Parts Illustration
HD45 PARTS ILLUSTRATION HD45 User Manual ◄ 17... -
Page 18: Hd45 Parts List
BACK-UP RING 07593 SPRING 02494 HANDLE GRIP 00224 RETAINER RING 01652 HOSE ASSY 03972 COUPLER, FEMALE 04936 CAPSCREW 03973 COUPLER, MALE 25534 WASHER 03971 COUPLER SET 04937 MOTOR CONTROL VALVE 05839 SEAL KIT 01211 O-RING 18 ► HD45 User Manual... -
Page 19: Underwater Tools Depth Guideline
ROV operation is still limited to the tool, for Depth (ft) 8 GPM 12 GPM example a percussive tool has the same depth 5/8” 5/8” limitation whether ROV or diver operated. 3/4” 1” 1” 1” 1000 1” 1-1/4” HD45 User Manual ◄... - Page 20 Stanley Hydraulic Tools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www.stanleyhydraulics.com...
Need help?
Do you have a question about the HD45 and is the answer not in the manual?
Questions and answers