Related Manuals for Stanley HD01
Summary of Contents for Stanley HD01
- Page 1 HD01 HYDRAULIC HAMMER DRILL afety peratiOn and aintenance USer ManUaL © 2012 Stanley Black & Decker, Inc. New Britain, CT 06053 U.S.A. 72659 5/2013 Ver. 4...
-
Page 2: Declaration Of Conformity
Combined Vibration Average 3 Axis -15.8 m/s² Disposizioni speciali: Representative in the Union: Patrick Vervier, Stanley Dubuis 17-19, rue Jules Berthonneau-BP 3406 41034 Blois Cedex, France. Vertreter in der Union/Représentant dans l’union/Representante en la Union/Rappresentante presso l’Unione Done at/Ort/Fait à/Dado en/Fatto a Stanley Hydraulic Tools, Milwaukie, Oregon USA... -
Page 3: Table Of Contents
REPAIRS AND / OR SERVICE TO THIS TOOL MUST ONLY BE DONE BY AN AUTHORIZED AND CERTIFIED DEALER. For the nearest authorized and certified dealer, call Stanley Hydraulic Tools at the number listed on the back of this manual and ask for a Customer Service Representative. -
Page 4: Safety Symbols
Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULATIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel. 4 ► HD01 User Manual... -
Page 5: Safety Precautions
Stay a safe distance away from electrical con- the space provided in this manual. ductors. The model HD01 Hydraulic Hammer Drill will provide • Do not operate tool in explosive atmospheres, such safe and dependable service if operated in accordance as in the presence of flammable liquids, gases or with the instructions given in this manual. -
Page 6: Tool Stickers & Tags
OPERATION MANUAL. OPERATION MANUAL. TAG TO BE REMOVED ONLY BY TAG TO BE REMOVED ONLY BY TOOL OPERATOR. TOOL OPERATOR. SEE OTHER SIDE SEE OTHER SIDE SAFETY TAG P/N 15875 (Shown smaller then actual size) 6 ► HD01 User Manual... -
Page 7: Hose Types
HOSE SAFETY TAGS To help ensure your safety, the following DANGER tags are attached to all hose purchased from Stanley Hydraulic Tools. DO NOT REMOVE THESE TAGS. -
Page 8: Hose Recommendations
HOSE RECOMMENDATIONS 8 ► HD01 User Manual... -
Page 9: Htma Requirements
2000 psi 2000 psi 2000 psi (at the power supply outlet) (172 bar) (138 bar) (138 bar) (138 bar) (138 bar) NOTE: These are general hydraulic system requirements. See tool specification page for tool specific requirements HD01 User Manual ◄ 9... -
Page 10: Operation
If you are in doubt about the type, test the tool by con- Closed-Center Forward and Reverse necting it to an open-center circuit with the trigger re- Select Select leased. If pressure rises more in the circuit with the trig- 10 ► HD01 User Manual... -
Page 11: Depth Gauge
Figure 3 OPEN-CENTER CLOSED-CENTER OC/CC The OC/CC selectable model has a knurled knob on the spool end holding the trigger strut and has two opposing set screws showing the circuit setting. If the set screws HD01 User Manual ◄ 11... -
Page 12: Drill Operation
DRILL OPERATION tion the handle assembly. Once in position, tighten the handle assembly by twisting the hand grip in a clockwise Operate the HD01 Hammer Drill as follows: direction. 1. Observe all safety precautions. Do not clamp the side handle to the front nose collar. -
Page 13: Cold Weather Operation
Press lightly. • Always replace hoses, couplings and other parts with Bull-point chisels that become blunt can be sharp ened on a replacement parts recommended by Stanley Hydraulic grinding machine. Tools. Supply hoses must have a minimum working pres- sure rating of 2500 psi/172 bar. -
Page 14: Lockout Kit, Open Center (Oc), Closed Center (Cc)
LOCKOUT KIT OC/CC DUAL SPOOL FEATURES FOR THE HD01 HAMMER DRILL KIT P/N-73018 IMPORTANT This tool is furnished with an on-off valve spool commonly referred to as a “dual spool” which permits adjustment so the tool may be operated on either an open-center hydraulic system or a closed-center hydraulic system. -
Page 15: Troubleshooting
Prevent reverse flow by using only one port from the valve for pressure, the return tool hose to the cooler and the filter line. Correct the quick-disconnect male/female routing per instructions and the arrows on the fittings. HD01 User Manual ◄ 15... - Page 16 Use pump size and rpm for producing needed controls. flow only. Eliminate circuit heating causes. Circuit has contaminants that have Replace worn pump and valves. Install a large caused wear and high heat generation. clean filter and keep the fluid clean. 16 ► HD01 User Manual...
-
Page 17: Specifications
Values determined according to ISO 28927-10:2011 ACCESSORIES DESCRIPTION PART NUMBER 1/2-inch Friction Chuck with Adaptor .........................72992 SERVICE PARTS DESCRIPTION PART NUMBER Seal Kit ................................72864 Service Kit (Includes items 6, and 59 thru 62 see illustration) ................72661 HD01 User Manual ◄ 17... -
Page 18: Hd01 Parts Illustration
HD01 PARTS ILLUSTRATION 18 ► HD01 User Manual... -
Page 19: Hd01 Parts List
TRIGGER SEAL KIT PART NUMBER 72864 16647 COMPRESSION COIL SPRING 16648 ROLL PIN 5/32 O.D. X .625 LG. HD01 SERVICE KIT 72661 (INCLUDES ITEM NUMBER 6, 59, 60, 17160 DANGER STICKER 61 and 62) 72958 NAME TAG /CAUTION HD01 17162... - Page 20 Stanley Hydraulic Tools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www.stanleyhydraulic.com IMPORTANT To fill out a Product Warranty Recording form, and for information on your warranty, visit Stanleyhydraulic.com and select the Warranty tab.