Alpine CDA-105Ri Owner's Manual page 44

Vehicle Display Interface Connector (Black)
Outputs Vehicle Display Interface control signals. Connect
this to the optional Vehicle Display Interface box.
For details about connections, consult your nearest Alpine
dealer.
Antenna Receptacle
Audio Interrupt In Lead (Pink/Black)
Connect this lead to the Audio Interface output of a cellular
phone which provides ground shorting when a call is
received.
Remote Turn-On Lead (Blue/White)
Connect this lead to the remote turn-on lead of your
amplifier or signal processor. When an IMPRINT audio
processor PXA-H100 (sold separately) is connected please
use the Remote Turn-on lead of PXA-H100 to connect to
your amplifier or signal processor. For details, refer to the
Owner's Manual of PXA-H100.
Switched Power Lead (Ignition) (Red)
Connect this lead to an open terminal on the vehicle's fuse
box or another unused power source which provides (+)
12V only when the ignition is turned on or in the accessory
position.
Ground Lead (Black)
Connect this lead to a good chassis ground on the vehicle.
Make sure the connection is made to bare metal and is
securely fastened using the sheet metal screw provided.
Power Antenna Lead (Blue)
Connect this lead to the +B terminal of your power antenna,
if applicable.
• This lead should be used only for controlling the vehicle's power
antenna. Do not use this lead to turn on an amplifier or a signal
processor, etc.
Dimmer Lead (Orange)
This lead may be connected to the vehicle's instrument
cluster illumination lead. This will enable the vehicle's
dimmer control to dim the backlighting of the unit.
Battery Lead (Yellow)
Connect this lead to the positive (+) post of the vehicle's
battery.
ISO Power Supply Connector
ISO Connector (Speaker Output)
Left Rear (+) Speaker Output Lead (Green)
Left Rear (–) Speaker Output Lead (Green/Black)
Left Front (+) Speaker Output Lead (White)
Left Front (–) Speaker Output Lead (White/Black)
Right Front (–) Speaker Output Lead (Grey/Black)
Right Front (+) Speaker Output Lead (Grey)
Right Rear (–) Speaker Output Lead (Violet/Black)
Right Rear (+) Speaker Output Lead (Violet)
Ai-NET Connector
Connect this to the output or input connector of other
product (CD changer, IMPRINT audio processor, Equalizer,
etc.) equipped with Ai-NET.
• Interface adapter for iPod (KCA-420i) is not recommended for use
with this product.
• You can input TV/video sound by connecting an optional Ai-NET/
RCA Interface cable (KCA-121B) to this component.
• Be sure to set "Setting the Connected Head Unit (MODEL SETUP)"
to "CD CHG", when the DHA-S690 is connected.
To prevent external noise from entering the audio system.
• Locate the unit and route the leads at least 10 cm away from the car harness.
• Keep the battery power leads as far away from other leads as possible.
• Connect the ground lead securely to a bare metal spot (remove any paint, dirt or grease if necessary) of the car chassis.
• If you add an optional noise suppressor, connect it as far away from the unit as possible. Your Alpine dealer carries various noise
suppressors, contact them for further information.
• Your Alpine dealer knows best about noise prevention measures so consult your dealer for further information.
42
-EN
Steering Remote Control Interface Connector
To steering remote control interface box.
For details about connections, consult your nearest Alpine
dealer.
Fuse Holder (10A)
Rear Output Input RCA Connectors
It can be used as Rear Output or Input RCA connectors.
RED is right and WHITE is left.
Front Output Input RCA Connectors
It can be used as Front Output or Input RCA connectors.
RED is right and WHITE is left.
Subwoofer Output RCA Connectors
RED is right and WHITE is left.
System Switch
When connecting a processor using Ai-NET, place the two
switches in the EXT AP position. When no device is
connected, leave the switch in the NORM position.
• Do not make the two switches to different settings.
• Be sure to turn the power off to the unit before changing the switch
position.
Power Supply Connector
Ai-NET Cable (Included with CD Changer)
RCA Extension Cable (sold separately)
ISO/JASO Antenna Adaptor (sold separately)
An ISO/JASO antenna adapter may be required, depending
on the vehicle.
Adaptive Steering Remote Control In 1 Lead (Brown/
Yellow)
To adaptive steering remote control interface box.
For details about connections, consult your nearest Alpine
dealer.
Adaptive Steering Remote Control In 2 Lead (Brown/
Orange)
To adaptive steering remote control interface box.
For details about connections, consult your nearest Alpine
dealer.
Adaptive Steering Remote G.GND
To adaptive steering remote control interface box.
For details about connections, consult your nearest Alpine
dealer.
Bluetooth interface connector (Blue)
Connect this to an optional Bluetooth INTERFACE (KCE-400BT).
To use a hands-free mobile phone, an optional Bluetooth
INTERFACE (KCE-400BT) connection is required. For
details on connection, refer to the Owner's Manual of the
Bluetooth INTERFACE (KCE-400BT). You can also connect
this to an external device (such as a portable player) by
using Conversion cable (KCE-237B) for building up the
AUX IN (sold separately).
* Refer to "Setting the AUX+ SETUP Mode" (page 21).
AUX+ ON : When the external device is connected.
AUX+ OFF : When set to OFF, AUX+ source cannot be
selected.
KCE-400BT Connection Cable (Included with
KCE-400BT)
USB Connector
Connect this to an USB memory or to an iPhone/iPod. To
use an iPhone/iPod, Interface cable for iPod connection is
required.
• Use the supplied USB cable. If a USB cable other than the supplied is
used, correct performance cannot be guaranteed.
• Route the USB cable away from other cables.