Stereo Effects Return Channel - ALLEN & HEATH VZ3 12:2 User Manual

The Stereo Effects Return Channel
AUX
FACTORY
PRESETS
1
SINGLE
1 STAGE
+6
OO
2 ROOM
AUX
2
3 HALL
4 PLATE
5 CHAMBER
+6
OO
6 CATHEDRAL
AUX
7 ARENA 3
8 GATED REV
9 KARAOKE
+6
OO
10 PING PONG
AUX
11 CHORUS
4
12 SLAP+REV
13 DLY+REV
+6
O O
14 ECHO+REV
1 9
15 CH+REV
16 PH+REV 2 10
DUAL
3 11
1 STAGE
4 12
2 ROOM
5 13
3 HALL
4 PLATE
6 14
5 CHAMBER
7 15
6 CATHEDRAL
8 16
7 ARENA
8 GATED REV
BANK
9 STAGE
10 ROOM
11 HALL SEL
12 SLAP DLY
ST5
/ FX
13 DELAY
LEV
14 ECHO
15 CHORUS
16 PHASER
+6
OO
MUTE
ST5
/ FX
PRE
AUX
1
+4
OO
AUX
2
+4
OO
AUX
3
+4
OO
AUX
4
+4
OO
AUX
5
+4
OO
AUX
6
+4
OO
SINGLE FX
DUAL FX
AUX5 = 1-8
AUX6 = 9-16
AUX5 = 1-16
3
WZ 16:2 12:2
and User Guide
AUX SENDS
The combined effects signal can be returned to
Auxes 1 to 4. These sends are not affected by the ST1 (ST5) LEV
control which returns the signal to the LR mix. The stereo signal is
summed to feed the auxes in mono. This can be changed if preferred
by repositioning internal jumper options so that L feeds auxes 1,3, and
R feeds auxes 2,4. Use the aux sends to add the effects to the
monitors if required.
Selecting the effects preset
through the available effects. The green indicator lights to show which
effect is active. Press BANK to change between preset 1-8 and preset
9-16. The red indicator lights to show presets 9-16 are selected. In
dual mode BANK toggles between the AUX5 and AUX6 effects
processor selections. The default preset names are printed on the
front panel for reference.
Turning off the internal effects
through all 16 effects the green indicator turns off showing that the
internal processor is turned off. Select this mode if you want to work
with external effects only.
ST1 (ST5) LEV
Returns the combined stereo effects to the main
LR mix. Adjust from fully off to +6dB maximum boost. Normal 3
0'clock 0dB operating position is marked on the panel.
MUTE
Press this switch to mute the stereo return channel. This
turns off the feed to the LR mix and the auxes. The channel may also
be muted using a footswitch plugged into the rear of the console. The
red indicator lights when the channel is muted by the MUTE switch
and/or the footswitch. Note that the MUTE switch is latching. This
means the channel shall remain muted as long as the switch is in its
pressed position regardless of the footswitch.
MODE
Recessed switch to prevent accidental operation. Situated
below the AUX6 master level control. Use a pen or sharp object to
change the setting. In the normal up position the processor is
configured as a SINGLE effects unit driven by AUX5. In the pressed
position the processor is configured as a DUAL effects unit driven by
AUX5 and AUX6.
EXTERNAL
SINGLE
AUX5
INTERNAL
AUX6
Resetting the effects presets
presets hold down the SEL key while powering up the console. Make
sure you do this while the amplifiers are turned off. The 8 green
indicators flash in sequence followed by the BANK indicator flashing on
then off to confirm the reset.
Press SEL to scroll down
Once you have scrolled
+
L/M
-
ST5
+
R
-
MIX
EFFECT
1-16
EFFECT
1-8
DUAL
EFFECT
9-16
To restore the factory default
L
R
19