Page 6
• test run the machine before starting any work. always wear a respira- tor when operating the model g0529. using this machine produces saw- dust which may cause allergic respiratory problems. g0529 oscillating Spindle & disc Sander reactions...
2: introduction foreword We are proud to offer the Model g0529 oscillating Spindle & disc Sander. this machine is part of a growing grizzly family of fine woodworking machinery. When used according to the guide- lines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of grizzly’s commitment to customer satis-...
Minimum Circuit Size ... 15 amps power connection device the Model g0529 comes with a 5-15 plug, similar to figure 1, to connect the machine to power. figure 1. typical 5-15 plug and receptacle. this machine must have a ground prong in the plug to help ensure that it is grounded.
5: set up unpacking the Model g0529 oscillating Spindle & 12" disc Sander was carefully packed at the factory. if you discover the machine is damaged after you have signed for delivery, and the truck and driver are gone, you will need to file a freight claim with the carrier.
-10- site considerations Weight load the Model g0529 weighs 166 lbs. and has a " X 16 " footprint. Most shop floors should be sufficient to carry the weight of the machine. reinforce the floor if you question its ability to support the weight.
6. note—Do not over tighten the spindle sleeve, it could make removal difficult. figure 7. installing spindle. g0529 oscillating Spindle & disc Sander...
7. figure 8. installing table inserts. g0529 oscillating Spindle & disc Sander squaring table to square the sanding tables: disconnect the machine from the power sup- ply.
12. figure 13. installing pSa sanding disc. g0529 oscillating Spindle & disc Sander aligning table the table must be spaced evenly away from the face of the sanding disc so that the sandpaper does not rub against the table.
2" diameter hose to connect a dust collection system to your dust ports. Start the dust collection system before oper- ating the sander. g0529 oscillating Spindle & disc Sander 2" dust ports...
(ansi). g0529 oscillating Spindle & disc Sander the Model g0529 sander is equipped with a paddle-type power switch with a safety key. to operate the power switch: loose...
Model g0529 produces an extremely fine sanding finish on edges or contours. the oscillation of the spin- dle disperses the material contact throughout the sanding sleeve to prevent burning. to perform spindle sanding operations:...
19. disc sanding with table tilted. g0529 oscillating Spindle & disc Sander the most efficient way to get a perfect miter is to cut the workpiece slightly long and sand it to the desired dimension.
• all the bearings are permanently lubricated and require no further lubri- cation long-term storage • Keep unpainted surfaces rust free with products such as Boeshield t-9. g0529 oscillating Spindle & disc Sander schedule switch key. onto ® ®...
Page 23
⁄ " X 1 ⁄ " X 8 ⁄ " ... g1511 2" X 2" X 12"... g1512 figure 21. pro-StiCK® abrasive cleaners. g0529 oscillating Spindle & disc Sander a/o sanding sleeves model h6659 h6660 h6661 h6662 h6663 h6664...
The information contained herein is deemed accurate as of 4/23/2008 and represents our most recent product specifications. -22- Model G0529 Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. MACHINE DATA SHEET g0529 oscillating Spindle & disc Sander PAGE 1 OF 2...
Page 25
The information contained herein is deemed accurate as of 4/23/2008 and represents our most recent product specifications. Model G0529 Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. g0529 oscillating Spindle & disc Sander PAGE 2 OF 2 -23-...
Always use the wiring diagram inside the motor junction box. your machine. 110 VAC 5-15 Plug (As Recommended) View this page in color at www.grizzly.com. g0529 oscillating Spindle & disc Sander...
CAP SCREW M6-1 X 15 POINTER LOCK WASHER 5MM PHLP HD SCR M5-.8 X 25 FLAT WASHER 1/4 CAP SCREW 5/16-18 X 3/4 LOCK WASHER 5/16 FLAT WASHER 5/16 CAP SCREW M5-.8 X 12 g0529 oscillating Spindle & disc Sander...
Page 29
PHLP HD SCR 10-24 X 3/8 PN01M HEX NUT M6-1 PB04 HEX BOLT 5/16-18 X 3 PB19 HEX BOLT 1/4-20 X 1/2 g0529 oscillating Spindle & disc Sander REF PART # DESCRIPTION P0529124 STAND TOP P0529131 MITER GAUGE BODY P0529132...
1. using too fine of sanding grit. piece. 2. using too much pressure. 3. Work held still for too long. g0529 oscillating Spindle & disc Sander troubleshooting possible Solution 1. Check power line for proper voltage. 2. inspect all lead connections on motor for loose or open connections.
Page 32
3. Make sure tension lever is in tensioning position. Follow sleeve tensioning instructions in this manual. 4. replace sanding sleeve/disc. 1. use back stop to support workpiece. 2. Start workpiece on a trailing corner. g0529 oscillating Spindle & disc Sander...