Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Chauvet Line Danser LED
Summary of Contents for Chauvet Line Danser LED
-
Page 1: User Manual
Snapshot Use on Dimmer Outdoor Use Sound Activated Master/Slave Auto-ranging Power Supply Replaceable Fuse User Serviceable Duty Cycle User Manual 3000 N 29 Ct, Hollywood, FL 33020 U.S.A. (800) 762-1084 – (954) 929-1115 FAX (954) 929-5560 www.chauvetlighting.com... -
Page 2: Table Of Contents
LAIMS ................................17 ECHNICAL PECIFICATIONS CHAUVET®, 2009, All Rights Reserved Information and specifications in this User Manual are subject to change without notice. CHAUVET® assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual. -
Page 3: Before You Begin
Manual Conventions CHAUVET manuals use the following conventions to differentiate certain types of information from the regular text. EANING... -
Page 4: Safety Instructions
Safety Instructions Please read these instructions carefully. It includes important information about the installation, usage and maintenance of this product. Please keep this User Manual for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet. Always make sure that you are connecting to the proper voltage, and that the line voltage you are connecting to is not higher than that stated on the decal or rear panel of the fixture. -
Page 5: Introduction
2. I NTRODUCTION Features 4-channel DMX-512 LED effect light Individual control of red, green and blue LEDs Variable speed of motor Built-in automated programs via master/slave or DMX Built-in sound activated programs via master/slave or DMX A d d i t i o n a l F e a t u r e s Additional power output: max 30 units 2. -
Page 6: Product Overview
Product Overview Single-yoke Hanging/Standing Brackets (2) Bracket Adjustment Knobs(2) Product Overview (rear panel) Power Indicator Safety Attachment Point DIP Switches DMX Out Signal Indicator DMX In Sound Sensitivity Power Adjustment Knob In/Fuseholder Microphone Power Link Out 2. Introduction 1/6/2010 11:34 AM... -
Page 7: Setup
3. S ETUP AC Power This fixture runs on 100~240 VAC, 50/60 Hz. Before powering on the unit, make sure the line voltage to which you are connecting it is within the range of accepted voltages. Always connect the fixture to a switched circuit. Never connect the fixture to a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used only as a 0 to 100% switch. -
Page 8: Mounting
Mounting Orientation The Line Dancer LED™ may be mounted in any safe position, provided there is adequate room for ventilation. Rigging Be sure that the structure can support the weight of the fixture. Please see the “Technical Specifications” section of this manual for a detailed weight listing. Mount the fixture securely. This may be done with a screw, nut and bolt, or a hanging clamp. -
Page 9: Operating Instructions
4. O PERATING NSTRUCTIONS Configuring the Starting Address Each fixture requires a starting address from 1~512. A fixture requiring one or more channels for control begins to read the data on the channel indicated by the starting address. For example, a fixture that uses seven DMX channels and is addressed to start on DMX channel 100, will read data from channels: 100, 101, 102, 103, 104, 105 and 106. -
Page 10: Standalone Operation
Standalone Operation Automatic This fixture has preprogrammed chases. These are accessed via the DIP switches on the back of the fixture. Please see the instructions below for further explanation. Set DIP switch [10] to the ON position. Set DIP switch [9] to the OFF position. Sound-Active This fixture has preprogrammed sound triggered chases. -
Page 11: Fixture Linking
Fixture Linking In order to use this fixture in a DMX or master/slave operation, you must daisy chain using DMX cables to link from one fixture to another. In a master/slave operation, the DMX controller is not connected. Fixture #1 DMX controller (only in DMX operation) Fixture #2... -
Page 12: Appendix
5. A PPENDIX DMX Primer There are 512 channels in a DMX connection. Channels may be assigned in any manner. A fixture capable of receiving DMX will require one or a number of sequential channels. The user must assign a starting address on the fixture that indicates the first channel reserved in the controller. There are many different types of DMX controllable fixtures and they all may vary in the total number of channels required. -
Page 13: Data Cabling
Data Cabling To link fixtures together you must obtain data cables. You can purchase CHAUVET® certified DMX cables directly from a dealer/distributor or construct your own cable. If you choose to create your own cable please use data-grade cables that can carry a high quality signal and are less prone to electromagnetic interference. -
Page 14: 3-Pin To 5-Pin Conversion Chart
3-Pin to 5-Pin Conversion Chart If you use a controller with a 5-pin DMX output connector, you will need to use a 5- pin to 3-pin adapter. The chart below details a proper cable conversion: IN TO ONVERSION HART Conductor 3-Pin Female (Output) 5-Pin Male (Input) Ground/Shield... -
Page 15: Setting The Starting Address
Interference from AC wires Keep DMX cables separated from power cables or black lights If you still have a problem after trying the above solutions, please contact CHAUVET® Technical Support. Contact Us W o r l d W i d e... -
Page 16: Returns Procedure
Package must be clearly labeled with a Return Merchandize Authorization Number (RMA #). Products returned without the RMA # will be refused. Call CHAUVET® and request an RMA # prior to shipping the fixture. Be prepared to provide the model number, serial number and a brief description of the cause for the return. -
Page 17: Technical Specifications
Technical Specifications WEIGHT & DIMENSIONS Length ........................12.9 in (327 mm) Width.......................... 12.4 in (316 mm) Height ........................11.5 in (291 mm) Weight........................... 9.2 lbs (4.2 kg) POWER Auto-ranging Power Supply ................100~240 VAC, 50/60 Hz Power Consumption @ 120 VAC, 60 Hz ..........8 W (0.2 A) max, 0.2 A inrush Power Consumption @ 230 VAC, 50 Hz ..........10 W (0.1 A) max, 0.2 A inrush Power output ........................
Need help?
Do you have a question about the Line Danser LED and is the answer not in the manual?
Questions and answers