Saving A Siriusxm Channel To The Presets List; Adjusting Siriusxm Satellite Radio Volume; Device Configuration; Turning On The Chartplotter Automatically - Garmin GPSMAP 800 series Owner's Manual

2 Select a category.

Saving a SiriusXM Channel to the Presets List

You can save your favorite channels to the presets list.
1
Select Media.
2
Select the channel you want to save as a preset.
3
Select MENU > Presets > Add Current Channel.

Adjusting SiriusXM Satellite Radio Volume

1
Select Media > MENU.
2
Select or .

Device Configuration

Turning On the Chartplotter Automatically

You can set the chartplotter to turn on automatically when the
power is applied. Otherwise, you must turn on the chartplotter
by pressing .
Select Settings > System > Auto Power.
NOTE: When Auto Power is On, and the chartplotter is
turned off using , and power is removed and reapplied
within less than two minutes, you may need to press
restart the chartplotter.

System Settings

Select Settings > System.
Display: Adjusts the backlight brightness and color scheme.
Beeper: Turns on and off the tone that sounds for alarms and
selections.
GPS: Provides information about the GPS satellite settings and
fix.
Auto Power: Turns on the device automatically when power is
applied (Turning On the Chartplotter
Language: Sets the on-screen text language.
Speed Sources: Sets the source of the speed data used to
calculate true wind speed or fuel economy. Water speed is
the speed reading from a water-speed sensor, and GPS
speed is calculated from your GPS position.
System Information: Provides information about the device
and the software version.
Simulator: Turns on the simulator and allows you to set the
speed and simulated location.

GPS Settings

Select Settings > System > GPS.
Skyview: Shows the relative position of GPS satellites in the
sky.
GLONASS: Turns on or off GLONASS usage (Russia satellite
system). When the system is used in situations with poor sky
visibility, this configuration can be used in combination with
GPS to provide more accurate position information.
WAAS/EGNOS: Turns on or off WAAS (in North America) or
EGNOS (in Europe), which can provide more-accurate GPS
position information. When using WAAS or EGNOS, the
device may take longer to acquire satellites.
Speed Filter: Averages the speed of your vessel over a short
period of time for smoother speed values.

Viewing the Event Log

The event log shows a list of system events.
Select Settings > System > System Information > Event
Log.
Device Configuration
to
Automatically).

Viewing System Software Information

You can view the software version, the basemap version, any
supplemental map information (if applicable), the software
version for an optional Garmin radar (if applicable), and the unit
ID number. You may need this information to update the system
software or to purchase additional map data information.
Select Settings > System > System Information >
Software Information.

My Vessel Settings

NOTE: Some settings and options require additional charts or
hardware.
Select Settings > My Vessel.
Keel Offset: Offsets the surface reading for the depth of a keel,
making it possible to measure depth from the bottom of the
keel instead of from the transducer location
Offset).
Temp. Offset: Compensates for the water temperature reading
from a NMEA 0183 water-temperature sensor or a
temperature-capable transducer
Temperature Offset).
Calibrate Water Speed: Calibrates the speed-sensing
transducer or sensor (Calibrating a Water Speed
Fuel Capacity: Sets the combined fuel capacity of all the fuel
tanks on your vessel (Setting the Fuel Capacity of the
Vessel).
Vessel Type: Enables some chartplotter features based on the
boat type.
Fill Up All Tanks: Sets the tank levels to full
Fuel Data with the Actual Vessel
Add Fuel to Boat: Allows you to enter the quantity of fuel you
added to your tank, when you did not entirely fill up the tank
(Synchronizing the Fuel Data with the Actual Vessel
Set Total Fuel Onboard: Sets the combined amount of fuel in
all the fuel tanks on your vessel
Data with the Actual Vessel
Set Gauge Limits: Sets the upper and lower limits of various
gauges (Customizing Engine Gauge and Fuel Gauge

Setting the Keel Offset

You can enter a keel offset to compensate the surface reading
for the depth of a keel, making it possible to measure depth
from the bottom of the keel instead of from the transducer
location. Enter a positive number to offset for a keel. You can
enter a negative number to compensate for a large vessel that
may draw several feet of water.
1 Complete an action, based on the location of the transducer:
• If the transducer is installed at the water line
the distance from the transducer location to the keel of the
boat. Enter this value in steps 3 and 4 as a positive
number.
• If the transducer is installed at the bottom of the keel
measure the distance from the transducer to the water
line. Enter this value in steps 3 and 4 as a negative
number.
(Setting the Keel
(Setting the Water
Device).
(Synchronizing the
Fuel).
Fuel).
(Synchronizing the Fuel
Fuel).
Limits).
, measure
,
25