Return the vacuum cleaner to a Vax Authorised Service Agent or CAUTION: The vacuum cleaner is a very powerful unit. Before plugging the suitably qualified person for examination, repair or adjustment.
Use & Function 3. Use & Function Align handle onto base of cleaner. IMPORTANT: Always remove the power plug from the electrical outlet before Using a Phillips or Flat Head screwdriver, secure the handle by inserting assembling or removing accessories. the provided four screws into the back of the handle (Fig.
How to Operate 4. How to Operate Transporting your Cleaner Use the carry handle located on the dirt container lid (Fig. 4/1). Fig. 4/3 Switch the upright vacuum cleaner on or off by pressing the on/off switch (Fig. 4/4). Fig. 4/1 Starting Up Holding the power cord by the plug, pull cord out completely.
How to Operate/Accessories 5. Accessories Vacuuming with Accessories Press the release button to release the stretch hose tube. The stretch hose tube with built-in brush can be used for cleaning surfaces (Fig. 5/1). Fig. 4/6 Brush Vacuuming on carpeted floors: •...
Accessories Straighten the hose and hook the hose clip into the fastening ring Then attach the accessory to the suction hose (Fig. 5/5). to prevent the upright vacuum cleaner from toppling over during use (Fig. 5/3). Hose Fastening Clip Ring Fig.
Accessories Use the stretch hose tube as an extension for long reaches (Fig. 5/7). Attach the mini Turbobrush to the suction hose (Fig. 5/10) or stretch hose tube (Fig. 5/11). Fig. 5/7 After vacuuming, slide the suction hose back into the stretch hose tube Fig.
Accessories/Dirt Container & Filter 6. Dirt Container & Filter: Removal & Attach the Flexible Extension Tube to the suction hose or stretch hose tube (Fig. 5/13). Replacement WARNING: To reduce the risk of injury from moving parts, unplug before servicing. NOTE: Unplug the vacuum cleaner before changing the filter.
Page 11
Dirt Container & Filter Tapping the container several times will help to loosen any dirt that may Close the dirt container and replace back into the vacuum cleaner until have become attached to the filter (Fig. 6/3). you hear it click (Fig. 6/6). Fig.
IMPORTANT: Switch off the vacuum cleaner and unplug from the wall outlet. NOTE: Vax recommend changing the post-motor filter every 12 months. Call Vax Care line on 0870 6061248 or visit www.vax.co.uk for further information. Remove the dirt container.
Page 13
Rotating Brushbar/Maintenance 7. Rotating Brushbar: Removal & Lift out the post-motor grille by pressing the locking tab and remove it (Fig. 6/12). Replacement The motor switches off automatically if the brushbar is blocked during operation by vacuuming up foreign objects, or if strands of carpet are wrapped around it.
Maintenance 8. Maintenance Pull the stretch hose to one side to remove it from the dirt container (Fig. 8/3). IMPORTANT: Switch off the vacuum cleaner and unplug it from the wall outlet before servicing. Hose Blockage IMPORTANT: Switch off the vacuum cleaner and unplug it from the wall outlet before servicing.
Page 15
Maintenance Return the stretch hose tube to the vacuum cleaner until it clicks into To reassemble, close top cover of mini Turbobrush and snap both locking place (Fig. 8/6). tabs into place (Fig. 8/9). Fig. 8/6 Fig. 8/9 Blockages in Mini Turbobrush Remove mini Turbobrush from end of suction hose.
Troubleshooting 9. Troubleshooting PROBLEM: Accessories won't pick up WARNING: TO REDUCE RISK OF PERSONAL INJURY, UNPLUG VACUUM CLEANER BEFORE SERVICING Cause: Accessories not attached correctly. Solution: Refer to page 7 for fitting information. PROBLEM: Cleaner won’t run PROBLEM: Brushbar does not turn Cause: Not properly plugged into wall outlet.
Monday-Friday 9.00am to 5.00pm. Power supply: 230-240V ~50Hz An answerphone is available outside of these hours. Any queries or concerns about using the Vax, call the Vax Careline. Calls are charged at Motor power: 1700W the UK national rate. Please make a note of the serial number and model number of the carpet Dirt container: 4.2 litres...
Page 18
This page has been intentionally left blank. VX-3 UK D4.indd 18 22/12/05 12:53:00...
Page 19
This page has been intentionally left blank. VX-3 UK D4.indd 19 22/12/05 12:53:00...
Page 20
EEC STATEMENT OF COMPLIANCE Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the product VX3 is manufactured in compliance with the following: Safety: 73/23/EEC Low Voltage Directive, as modified by 93/68/EEC EMC: 89/336/EEC Electromagnetic Compatibility Directive, as modified by 93/68/EEC Waste electrical products should not be disposed of with household waste.
Need help?
Do you have a question about the VX3 and is the answer not in the manual?
Questions and answers