Cisco Telepresence MX300 Administrator's Manual page 37

Cisco TelePresence MX Series
AdministrAtor guide
Table of contents Introduction
Conference [1..1] MicUnmuteOnDisconnect Mode
Determine if the microphones shall be unmuted automatically when all calls are disconnected. In
a meeting room or other shared resources this could be done to prepare the system for the next
user.
Requires user role: ADMIN
Value space: <On/Off>
On: Un-mute the microphones after the call is disconnected.
Off: If muted, let the microphones remain muted after the call is disconnected.
Example: Conference 1 MicUnmuteOnDisconnect Mode: On
Conference [1..1] DoNotDisturb Mode
Determine if there should be an alert on incoming calls.
Requires user role: USER
Value space: <On/Off>
On: All incoming calls will be rejected, with no alert. The calling side will receive a busy signal
when trying to call the codec. A message will display on screen, telling that Do not disturb is
turned on, together with an option to turn off the Do not disturb. When turning off the Do not
disturb mode you will see a list of the calls that have been rejected.
Off: The incoming calls will be alerted.
Example: DoNotDisturb Mode: Off
Conference [1..1] FarEndControl Mode
Lets you decide if the remote side (far end) should be allowed to select your video sources and
control your local camera (pan, tilt, zoom).
Requires user role: ADMIN
Value space: <On/Off>
On: Allows the far end to be able to select your video sources and control your local camera
(pan, tilt, zoom). You will still be able to control your camera and select your video sources as
normal.
Off: The far end is not allowed to select your video sources or to control your local camera
(pan, tilt, zoom).
Example: Conference 1 FarEndControl Mode: On
Conference [1..1] FarEndControl SignalCapability
Set the far end control (H.224) signal capability mode.
Requires user role: ADMIN
Value space: <On/Off>
On: Enable the far end control signal capability.
Off: Disable the far end control signal capability.
Example: Conference 1 FarEndControl SignalCapability: On
D14850.02 MX Series Administrator Guide (TC5.0) | 2011 NOVEMBER | © 2011 Cisco Systems, Inc. All rights reserved.
Web interface Advanced settings Advanced settings Appendices
Conference [1..1] Encryption Mode
Set the conference encryption mode. A padlock with the text "Encryption On" or "Encryption
Off" displays on screen for a few seconds when the conference starts.
Requires user role: ADMIN
Value space: <BestEffort/On/Off>
BestEffort: The system will use encryption whenever possible.
> In Point to point calls: If the far end system supports encryption (AES-128), the call will be
encrypted. If not, the call will proceed without encryption.
> In MultiSite calls: In order to have encrypted MultiSite conferences, all sites must support
encryption. If not, the conference will be unencrypted.
On: The system will only allow calls that are encrypted.
Off: The system will not use encryption.
Example: Conference 1 Encryption Mode: BestEffort
Conference [1..1] DefaultCall Protocol
Set the Default Call Protocol to be used when placing calls from the system.
Requires user role: ADMIN
Value space: <H323/Sip>
H.323: Select H.323 to ensure that calls are set up as H.323 calls.
Sip: Select SIP to ensure that calls are set up as SIP calls.
Example: Conference 1 DefaultCall Protocol: H323
Conference [1..1] DefaultCall Rate
Set the Default Call Rate to be used when placing calls from the system.
Requires user role: ADMIN
Value space: <64..6000>
Range: Select a value between 64 and 6000 kbps
Example: Conference 1 DefaultCall Rate: 768
Conference [1..1] MaxTransmitCallRate
Specify the maximum transmit call rate to be used when placing or receiving calls.
Requires user role: ADMIN
Value space: <64..6000>
Range: Select a value between 64 and 6000 kbps.
Example: Conference 1 MaxTransmitCallRate: 6000
37
www.cisco.com