Channel Control Punch-Through; Transport Control Punch-Through; Resetting The Remote Memory - Harman Kardon AVR 135 Owner's Manual

Programming the Remote
2. Press the Volume Up button
that.the Program/SPL Indicator
flashing and stay amber.
3. Press either the AVR Selector
Input Selector , depending on which
system's volume control you wish to have attached
for the punch-through mode. The Program/SPL
Indicator will blink green three times and
then go out to confirm the data entry.
Example: To have the AVR's volume control acti-
vated even though the remote is set to control
the TV, first press the Video/TV Input Selector
and the Mute button at the same time.
Next, press the Volume Up button
by the AVR Input Selector .
NOTE: Should you wish to return the remote to
the original configuration after entering a Volume
Punch-Through, you will need to repeat the steps
shown above. However, press the same Input
Selector in steps one and three.

Channel Control Punch-Through

The AVR's remote may be programmed to operate
so that the channel control function, performed
with the Sleep and Surround
for either the TV, cable or satellite receiver used in
your system may be used in conjunction with one
of the other devices controlled by the remote. For
example, while using and controlling the VCR,
you may wish to change channels on a cable box
or satellite receiver without having to change the
device selected by the AVR or the remote. To pro-
gram the remote for Channel Control Punch-
Through, follow these steps:
1. Press the Input Selector button
device you wish to have the channel control
associated with and the Mute button
same time until the red light illuminates under the
Input Selector and the Program/SPL
Indicator flashes amber.
2. Press the Volume Down button
Program/SPL Indicator will stop flashing
and stay amber.
3. Press and release the AVR or Input
Selector button for the device that will be
used to change the channels. The Program/SPL
Indicator will blink green three times and
then go out to confirm the data entry.
Example: To control the channels using your TV
while the remote is set to control the VCR, first
press the VID 1/VCR Input Selector button
and the Mute button at the same time. Next,
release them and press the Volume Down button
, followed by the same Input Selector but-
ton .
NOTE: To remove the Channel Control Punch-
Through and return the remote to its original con-
figuration, repeat the steps shown in the example
above. However, press the same Input Selector
in Steps 1 and 3.
and note

Transport Control Punch-Through

will stop
The AVR's remote may be programmed to operate
so that the Transport Control Functions
or the
(Play, Stop, Fast Forward, Rewind, Pause and
Record) for a VCR, DVD or CD will operate in con-
junction with one of the other devices controlled
by the remote. For example, while using and con-
trolling the TV, you may wish to start or stop your
VCR or DVD without having to change the device
selected by the AVR or the remote. To program the
remote for Transport Control Punch-Through, fol-
low these steps:
1. Press the Input Selector
, followed
you wish to have the channel control associated
with and the Mute button
until the red light illuminates, under the Input
Selector and the Program/SPL Indicator
flashes amber.
2. Press the Play button
Indicator will stop flashing and stay amber.
3. Press and release the AVR
Selector button
used to change the channels. The Program/SPL
Indicator will blink green three times and
then go out to confirm the data entry.
buttons,
Example: To control the transport of a CD player
while the remote is set to control the TV, press the
VID 2/TV Input Selector button
Mute button
them and press the Play button
the CD Input Selector button
NOTE: To remove the Channel Control Punch-
Through and return the remote to its original con-
figuration, repeat the steps shown in the example
above. However, press the same Input Selector
for the
in Steps 1 and 3.
NOTE: Before programming the remote for
at the
Volume, Channel or Transport Punch-Through,
make certain that any programming needed for
the specific TV, CD, DVD, Cable or Satellite
Receivers has been completed.
. The
for the device
at the same time
. The Program/SPL
or Input
for the device that will be
and the
at the same time. Next, release
, followed by
.

Resetting the Remote Memory

As you add components to your home-theater
system, occasionally you may wish to totally repro-
gram the remote control without the confusion of
any commands, macros or "Punch-Through"
programming that you may have done. To do this,
it is possible to reset the remote to the original
factory defaults and command codes by following
these steps. Note, however, that once the remote is
reset, all commands or codes that you have
entered will be erased and will need to be re-
entered:
1. Press any of the Input Selector buttons
and the "O" button at the same time until
the Program/SPL Indicator begins to flash
amber.
2. Press the "3" button three times.
3. The red LED under the Input Selector
go out and the Program/SPL Indicator
stop flashing and turn green.
4. The Program/SPL Indicator
green until the remote is reset. Note that this may
take a while, depending on how many commands
are in the memory and need to be erased.
5. When the Program/SPL Indicator
out, the remote has been reset to the factory
settings.
PROGRAMMING THE REMOTE 37
will
will
will remain
goes