1. Manuals
  2. Brands
  3. CFM Manuals
  4. Grill
  5. BLACKSTONE 1000
  6. Owner's manual

CFM BLACKSTONE 1000 Owner's Manual

Gas barbecue
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Formerly:
Now:
®
CFM Corporation

Advertisement

Table of Contents
loading

Related Manuals for CFM BLACKSTONE 1000

Summary of Contents for CFM BLACKSTONE 1000

  • Page 1 Formerly: Now: ® CFM Corporation...
  • Page 2 Eastern Standard time, Monday through Friday. We want you to be completely satis ed with your purchase Formerly: ® Now: CFM Corporation 2695 Meadowvale Boulevard Mississauga, Ontario L5N 8A3 Canada (800) 668-5323 www.cfmcorp.com Service Note: If you are experiencing difficulties or are dissatisfied with your purchase, please contact CFM at...
  • Page 3 Teem oF CoNTENTS CxnprcR Orue - INSTALLATION CHOOSING A SAFE LOCATION Cxeprgn Two - PORTABLE GAS GRILL BASICS 5 - 7 FUEL FUEL SUPPLY SYSTEM FUEL REGULATORAND HOSE FUEL CYLINDER SPECIFICATIONS TRANSPORTING A FULL CYLINDER TAKE THESE INSTRUCTIONS TO THE L.P. GAS DEALER FILLING and PURGING TYPE 1 L.P.
  • Page 4 CHapren OHe - INSTALLATION lf these instructions are ignored, there is a possibility of a hazardous fire or explosion which could result in physical injury or prop- erty damage! lt is your responsibility to as- semble, operate and maintain your gas grill properly.

  • Page 5: Fuel Supply System

    Cnepren Two - PORTABLE GAS GRILL BASICS F U E L 4. The pressure regulator and hose assem- This appliance is designed to use Liquid Propane gas (abbreviated LP gas or pro- bly provided is factory set at an outlet pres- pane).
  • Page 6 You should transport only one cylinder at a tion (DOT) or the National Standard of time. Transport the cylinder in an upright Canada, CAN/CSA-8339, Cylinders , and secure manner with control valve turned Spheres and Tubes for Transportation of off and the POL plug in place. Dangerous Goods;...
  • Page 7 PURGING and EVACUATION DEVIGES for TAKE THESE INSTRUCTIONS TO THE LP LP GAS CYLINDERS with ryPE 1 GYLIN- GAS DEALER. DER VALVES When using a cylinder exchange be sure the A. Hose end valve with a bleed port: Purging exchanged cylinder is a Type 1 cylinder, as can be accomplished using a hose end a 510 POL cylinder will not fit Type 1 regula- valve containing a bleed port which also al-...
  • Page 8 Csapren THnEe - ASSEMBLY INSTRUCTIONS Assembly Step 1. Getting Started; 1. Please follow the steps in the order that Unpack Grill Parts. they are presented. 2. Assemble the grill at the location that you 1. Remove and set aside all inner boxes intend to use it.
  • Page 9 side tables ( 2 ) g r i l l bottom casting ( 1 ) cooking grids ( 2 piece ) handle ( 1 ) handle standoff ( 2 1 warming rack standoff gasket \ ( 1 ) ( 2 ) gr il l l id L.P.
  • Page 10 Assernbly Step 2. hardware bag "A" Attach the Pillar containing: to the Base. tools needed: a 318" open end wrench a7l16" open end wrench base Lock the pre-assembled casters ( 1 ) on base by pushing down on the latch. (Th.is symbol is to help ,iffi lr'ffiJ...
  • Page 11 2. Position the pillar upside-down and set the base onto the pillar as shown. Working from the open side of pillar: 3. Insert bolts through the two slots at the front of the pillar and through the holes in the front of the base.
  • Page 12 Assembty Step 3. Attach the Grill Bottom to the Pillar. 4ffi - & \ fools needed: a 3/B" open end wrench a7l16" open end wrench <5::< >L1:D {:5:-.d A*I}R €r< €5j< 4-5tZ ?,F.4 *."i5 ffi'| T:U' 14-20 x 1" ( 4 ) Position the grill bottom onto the pillar so that the rear hinge struts are toward the open side of the pillar, as shown.
  • Page 13 r _ l - r i l _ \ U J 3. IMPORTANT: Make sure the control 5. Locate the two black lead wires beneath the qrill bottom. Press the valve ends are inside the burner tubes extending through the grill bottom. loose ends oithe lead wires onto the metal tabs located on the back of the 4.
  • Page 14 Assembly Step 4. Attach Side Tables to the Grill Bottom. a 3/B" open end wrench a7116" open end wrench (9.. hardware bag "C" containing: Insert 3/4" bolts through holes in the support arms of the side tables, as shown. Slide a gasket washer over the threaded end of the bolt.
  • Page 15 4 . Attach the side table to the four holes located in the side of the grill bottom using the locking hex nuts provided. Attach the opposite side table in the same manner. (.\*i\ $:-i-;]x\...
  • Page 16 Assembly Step 5. the Grill Lid Assembly hardware bag "D" containing: hair pin (2') \:-\Az f f i @ @ r , hinge pin fools needed: 114-20 '| 14x1118" 114-20 x 5/8" a7l16" open end wrench ( 4 ) ( 2 1 ( 4 ) a flat blade screwdriver Position the back of the lid so that the...
  • Page 17 Hold the lid to align the hinge holes. Insefi a hinge pin through the hinge hole in the lid and into the hole in the bottom hinge strut. -E€ After the hinge pin is in place, insert a \" 4. hair pin through the hole of the hinge pin to secure it.
  • Page 18 Installing the Internal Assernbly Step 6. C o m p o n e n t s i n t h e G r i l l . no tools needed rock-grate ( 1 ) ceramic briquettes ( 1 b a g ) Place the single rock-grate into the grill bottom.
  • Page 19 2. Open the package containing the ceramic briquettes. 3. lt is important to properly arrange them onto the rock-grate to allow for good air flow during use. NOTICE THE SPACING: The proper amount of briquettes are supplied and there is no need to add more.
  • Page 20 Assembly Step 7. Installing the Gas SuPPIY Cylinder. L.P. gas cylinder ( 1 ) Gonnecting the Regulator to Gylinder coupling nut connects to the large outside threads on the valve outlet' Use care not to cross-thread the connection. 5. Handtighten the coupling nut clockwise and tighten until it comes to a full stop' Tighten by hand only.
  • Page 21 Position the cylinder retainer wire around the cylinder collar as shown. lnsert the left end of the wire into the small opening in the base. Flex the right side so that it fits into the opposite opening on the right side of the base.
  • Page 22 Assembly Step 8. Completing the Assembly 2. Place an aluminum pan into the 1. Place the heat shield inside the opening in the heat shield to catch pillar above the cylinder. grease drippings during use. NATURAL GAS MODELS no tools needed heat shield ( 1 ) LP gas style...
  • Page 23 CnRpren Foun - LEAK TESTING DANGER Perform a leak test each time the gas supply To Prevent Fire or Explosion Hazard: cylinder is connected to the regulator. Leak ' N O S M O K I N G ! test any time a paft of the gas system is re- ' Do not permit any sources of ignition in ihe placed.

  • Page 24: Ignitor Lighting System

    CHapren Ftve - OPERATING YOUR NEW GRILL S T E P 3 . O P E N G R I L L L I D ! IGNITOR LIGHTING SYSTEM io light the grill with WAR[\lNG:Attempting the lid down could cause an explosion. The lgnitor System is made up of the igniter unit, a gas collector box, two ceramic elec- STEP 4.

  • Page 25: How To Shut Off The Grill

    MATCH LIGHTING HOW TO SHUT OFF THE GRILL IMPORTANT! The match lighting hote is found under the front right corner of the grill STEP 1. Turn the burner control knob(s) to bottom. When match lighting the grill, use off. The burner flame will go out. the gas control knob on your RIGHT-HAND side (closest to the match lighting hole).

  • Page 26: Burner's Flame

    Gnapren Sx - USING the GRILL \.-' lf flames are excessively yellow and irregu- TO BREAK lN A NEW GRILL before using it for the first time; operate the grill with lid lar, the oil residue may not be completely burnt off.

  • Page 27: In Case Of A Major Grease Fire

    During operation, stand to side of grill when 3. lf doing skillet or stir-fry cooking, limit the opening the grill lid. Lift lid handle slowly in amount of oil and direct heat used. case of a grease flare-up. Do Not expose any part of your body directly above the 4.
  • Page 28 Cnnpren EtcHr - CONNECTING TO NATURAL GAS (for specially equipped natural gas grills only) \ /ARNIING: Do not use Liquid Propane Gas A quick connect coupling sleeve with 3/8" in a unit designed for Natural Gas. female end is provided. Install the connector lf the appliance is for connection to Natural at the pipe end, after the shut-off valve.
  • Page 29 CHapren Nnre- REPLACEMENT PARTS Replacement parts are available direct from Please have your order ready when you call. our warehouse. Some components are not Some charges for replacement parts and available pre-assembled after the point of shipping may apply. purchase. These parts may be ordered separately upon request.

Table of Contents