Table of Contents
Advertisement
Quick Links
Formerly:
Assembly and
Owner's Manual
Portable
Gas Grill
6000
Series
8000
Series
ASSEMBLER / INSTALLER:
Leave these instructions with the consumer.
CONSUMER / USER:
Read all of these instructions and keep them in a safe place for future reference.
FOR YOUR SAFETY
If you smell gas:
1
Shut o gas to the appliance.
2
Extinguish any open ame.
3
Open lid.
4
If odor continues, immediately call
your gas supplier or re department.
FOR YOUR SAFETY: Never leave a grill unattended when in use.
Now:
®
FOR YOUR SAFETY
1
Do not store or use gasoline or other
ammable vapors and liquids in the
vicinity of this or any other appliance.
2
An unconnected liquid propane
cylinder should not be stored in the
vicinity of this or any other appliance.
CFM Corporation
Advertisement
Table of Contents
Related Manuals for CFM 6000 Series
Summary of Contents for CFM 6000 Series
- Page 1 Formerly: Assembly and Owner’s Manual Portable Gas Grill 6000 Series 8000 Series ASSEMBLER / INSTALLER: Leave these instructions with the consumer. CONSUMER / USER: Read all of these instructions and keep them in a safe place for future reference. FOR YOUR SAFETY If you smell gas: Shut o gas to the appliance.
- Page 2 Statement of Commitment Congratulations and thank you for your purchase of your new Great Outdoors grill. We are pleased that you have recognized the value of the design, function, and quality of components used in this product. We believe it is among the nest on the market.
-
Page 3: Table Of Contents
Table of Contents Chapte r 1 - INSTALLATION Necessary Information Choosing a Safe Location ......Portable L.P. Gas Grills L.P. -
Page 4: Chapte R 1 - Installation
6000, 8000 Series Gas Grill Installation Necessary Information to Safely Use a Gas Grill The gas fuel used by this product is highly flammable and must be used in a responsible and cautious manner. It is your responsibility to assemble, operate, and maintain your gas barbecue grill properly. -
Page 5: Portable L.p. Gas Grills
6. Do Not store a spare L.P. gas cylinder under or near this appliance. Do not store an L.P. cylinder in a building, garage or any other enclosed area. Instead, store the cylinder outdoors in a well ventilated area, away from people and out of the reach of children. - Page 6 Dual Burner Fuel-Control Valve Type 1 Fuel Regulator Fuel Supply The L.P. Fuel Supply System (the fuel regulator and hose) FUEL REGULATOR AND HOSE The fuel regulator supplied is equipped with a Type 1 coupling nut. Do not attempt to connect to any other L.P.
- Page 7 terminating in a Type 1 L.P. gas-cylinder- valve outlet. A Type 1 compatible cylinder with a Type 1 cylinder valve has a positive seating connection that does not permit gas flow until a positive seal has been obtained. The cylinder must be arranged for vapor withdrawal.
-
Page 8: Gas Dealer Instructions
Take These Instructions to the L.P. Gas Dealer When using a cylinder exchange, be sure the exchanged cylinder is a Type 1 cylinder; a 510 POL cylinder will not fit a Type 1 regulator. FILLING AND PURGING TYPE 1 L.P. GAS CYLINDERS DANGER: Purging and filling of L.P. -
Page 9: Chapter 2 - Assembly Instructions
6000, 8000 Series Gas Grill Assembly Instructions Tools needed to assemble grill: · flat-head screwdriver · phillips-head screwdriver (For side burner equipped grills) · 3/8” open-end wrench* · 7/16” open-end wrench* A socket set or an adjustable wrench may be used in place of the open-end wrenches. -
Page 10: Step 1 ( Identifying Parts )
Assembly Step 1 - Identifying the Grill Parts Locate these parts: handle standoff (2) handle (1) warming rack (1) cast iron cooking grids 6100 series 8100 series (2) rock grate (1) side table (2) base (1) (2 locking casters and 2 non-locking casters Installed) cylinder retainer... -
Page 11: Step 2 ( Assemble Pillar To Base )
Assembly Step 2 - Attach the Base to the Pillar Tools Needed: 3/8” wrench USE HARDWARE BAG 1/4-20 hex nut (4) 1/4-20 x 3/4” bolt (4) LOCATE THESE PARTS: pillar assembly (1) base assembly (1) locking casters 7/16” wrench back side of base, upside down Lock the pre-assembled casters on base by pushing down on the latch. -
Page 12: Step 3 ( Attach Grill Bottom )
Assembly Step 3 - Attach Grill Bottom to Pillar Tools Needed: 3/8” wrench USE HARDWARE BAG 1/4-20 nut (4) 1/4-20 x 1” bolt (4) LOCATE THESE PARTS: grill bottom assembly (1) heat shield (1) 7/16” wrench Working from the back (open) side of the pillar, set the heat shield on top of the pillar. - Page 13 IMPORTANT: Make sure the control valve ends are properly seated inside the burner tubes as shown. (The control valve ends are attached to the pillar; the burner tubes are attached and extend through the grill bottom.) Locate the two black igniter wires beneath the grill bottom.
-
Page 14: Step 4 ( Side Tables )
Assembly Step 4 - Attach the Side Tables Tools Needed: 3/8” wrench 7/16” wrench USE HARDWARE BAG 1/4-20 hex nut (8) LOCATE THESE PARTS: 1/4-20 x 3/4” bolt (8) side table (2) Insert the 3/4” bolts through the holes in the support brackets of the side table. -
Page 15: Step 5 ( Assemble Grill Lid )
Assembly Step 5 - Assemble the Grill Lid Tools Needed: flat-head screwdriver 7/16” wrench LOCATE THESE PARTS: handle (1) Heat Indicator (1) Push Nuts for Heat Indicator (2) Place the heat indicator onto the front of the grill lid, lining up the 3 prongs with the 3 mounting holes. - Page 16 Assembly Step 5 - continued Hold the lid to align the hinge holes. Insert a hinge pin through the hinge hole in the lid and into the hole in the bottom hinge strut. After the hinge pin is in place, insert a hair pin through the hole of the hinge pin to secure it.
-
Page 17: Step 6 ( Internal Parts )
LOCATE THESE PARTS: rock grate ceramic briquettes (1 package) cast iron cooking grids 6000 series (1) 00 series warming rack Place the single rock grate into the grill Place the single rock grate into the grill bottom. bottom. Open the package containing the... - Page 18 (6000 series grills are equipped with one large single cooking grid in place of the 2 grids) Set the warming rack onto the back of the cooking grids.
-
Page 19: Installing An L.p. Gas Cylinder
Installing an L.P. Gas Cylinder Items Needed: L.P. Gas Cylinder (1 FILLED) NOTE: Some L.P. grill models DO NOT include an L.P. gas cylinder LOCATE THESE PARTS: cylinder retainer wire (1) (Back side, under grill bottom) Obtain a filled L.P. gas cylinder. Read and follow all directions on the cylinder and fuel hose safety tags. -
Page 20: Connecting The L.p. Gas Cylinder
Connecting the L.P. Gas Cylinder Connecting the Regulator to Cylinder 1. The top knob on the supply cylinder must be closed. See that the top cylinder knob is turned clockwise to a full stop. 2. Check that all the grill burner knobs are turned off. -
Page 21: Connecting To Natural Gas
Natural Gas Grills - Connecting to Natural Gas (for specially equipped natural gas grills only) DANGER: EXPLOSIVE AND FLAMMABLE! If the appliance is for connection to natural gas, the gas connections should be made by a qualified installer or a licensed plumber. The gas-supply line must not be installed by the consumer. - Page 22 Natural Gas Grills - Connecting to Natural Gas (for specially equipped natural gas grills only) OPERATING THE QUICK-CONNECT Follow all directions on tags attached to hose. 1. To connect the fuel-supply hose to the fuel supply, the shut-off valve must be closed. 2.
- Page 23 Do not clean any electrical product with a water spray or the like. Store electrical products indoors out of reach of children when not in use. 1-800-944-8982 1-800-668-5323 Model number cross reference: 6000 = VC0620P Parts Enclosed part no. quantity AM000505...
- Page 24 Model 6000 Series Components 6000 Series Parts quantity description Grill Lid Rock Grate Cast Iron Cooking Grid 1 pkg Ceramic Briquettes BOTTOM / BURNER ASSEMBLY Bottom / Burner Assembly consisting of: Cast Brass Burner Venturi Tube Venturi Gasket #8-32 x 1/2” Screw...
- Page 25 Model 8000 Series Components Model number reference: VC0680P and VC0680N 8000 Series Parts quantity description Grill Lid Rock Grate Cast Iron Cooking Grids 1 pkg Ceramic Briquettes BOTTOM / BURNER ASSEMBLY Bottom / Burner Assembly consisting of: Cast Brass Burner Venturi Tube w/gasket #8-32 x 1/2”...