Spray Tip Selection Chart; Aam Fine Finish Spray Tips; Gg4 Industrial Spray Tips - Graco 288844 Instructions Manual

Spray Tip Selection Chart

Spray Tip Selection Chart
Spray Tips, for use with AA Series Air Cap

AAM Fine Finish Spray Tips

Recommended for high finish quality applications at low and medium pressures. Order desired tip
(Part No. AAMxxx) from matrix below.

GG4 Industrial Spray Tips

Recommended for high wear applications at high pressures. Order desired tip (Part No. GG4xxx) from matrix below.
• All tips in the Spray Tip Selection Chart below
can be used with Model G40 guns (249242).
Use tips in the gray shaded area of the chart
with Model G40 guns only.
• Do not use tips in the gray shaded area of the
chart with Model G15 guns (288844).
* Fluid Output, fl oz/min (lpm)
Orifice Size in. at 600 psi
(mm) (4.1 MPa, 41 bar)
† 0.007 (0.178) 4.0 (0.1)
† 0.009 (0.229) 7.0 (0.2)
† 0.011 (0.279) 10.0 (0.3)
0.013 (0.330) 13.0 (0.4)
0.015 (0.381) 17.0 (0.5)
0.017 (0.432) 22.0 (0.7)
0.019 (0.483) 28.0 (0.8)
0.021 (0.533) 35.0 (1.0)
‡ 0.023 (0.584) 40.0 (1.2)
‡ 0.025 (0.635) 50.0 (1.5)
‡ 0.027 (0.686) 58.5 (1.7)
‡ 0.029 (0.737) 68.0 (1.9)
‡ 0.031 (0.787) 78.0 (2.2)
‡ 0.033 (0.838) 88.0 (2.5)
‡ 0.035 (0.889) 98.0 (2.8)
‡ 0.037 (0.940) 108.0 (3.1)
‡ 0.039 (0.991) 118.0 (3.4)
* Tips are tested in water.
Fluid output (Q) at other pressures (P) can be calculated by this formula: Q = (0.041) (QT)
where QT = fluid output (fl oz/min) from the above table for the selected orifice size.
† These tip sizes include a 150 mesh tip filter.
‡ Do not use these tips with Model G15 guns (288844).
★ GG4 tips only.
30
at 1000 psi 2 to 4
(7.0 MPa, 70 bar) (100)
★107
5.2 (0.15) 207
9.1 (0.27) 109 209
13.0 (0.4) 111 211
16.9 (0.5) 213
22.0 (0.7) 215
28.5 (0.85) 217
36.3 (1.09) 219
45.4 (1.36)
51.9 (1.56)
64.8 (1.94)
75.8 (2.27)
88.2 (2.65)
101.1 (3.03)
114.1 (3.42)
127.1 (3.81)
140.0 (4.20)
153.0 (4.59)
SKIN INJECTION HAZARD
Do not use tips in the gray shaded area of the Spray
Tip Selection Chart with Model G15 guns (288844).
Failure to follow this warning can result in serious
injury or amputation.
Maximum Pattern Width at 12 in. (305 mm)
4 to 6 6 to 8 8 to 10 10 to 12
(150) (200) (250)
307
309 409 509
311 411 511
313 413 513
315 415 515
317 417 517
319 419 519
321 421 521
423 523
425
527
431
435
539
12 to 14 14 to 16 16 to 18
(300) (350) (400)
611
613 713
615 715 815
617 717 817
619 719 819
621 721 821
623 723
625 725 825
627 827
629
631
★833
633
737
639 839
P
18 to 20
(450) (500)
917
919
921
923
311001F