Safety information Use the power adaptor and the Do not use the BT In Touch 1000 batteries supplied. Replacement in damp, humid conditions such batteries and power adaptors are as bathrooms. available from the Helpline on 0845 6011 406. The power adaptor item code is: 872026.
Using your phone the caller’s home in the event of an emergency Making and receiving calls Optional settings of the BT In Touch 1000 Using handsfree To set the voice prompts to ON or OFF To adjust the speaker volume...
BT In Touch 1000 Pendant receiver aerial Aerial receives the Pendant signal to remotely activate the emergency sequence or automatically answer an incoming call in handsfree. At a glance In Touch 1 Handset hook When the phone has been wall- mounted, it keeps the handset in place.
Page 5
Recall button Use with some BT Calling Features and for transferring calls on certain switchboards. Announce button (under Quickdial memory label) Use to listen to messages and to record your own personal message (via the handset).
Introduction You can expect your BT In Touch 1000 to provide Unpacking your BT In Touch 1000 many years of quality service. Please read the instructions carefully before use and keep this user Check that your BT In Touch 1000 is complete.
Locate your phone within 2 metres of a phone socket. Open the battery cover on the underside of your BT Warning In Touch 1000. Insert the 6 x AA rechargeable batteries. Your BT In Touch 1000 is only designed to operate in a normal domestic environment.
Page 8
Plug the power cable into the socket on the This should be done before you attach the base underside of your BT In Touch 1000 as shown. The stand for either raised or wall-mounted positions. cable needs to be pressed in to its channel to keep it out of the way.
Page 9
Positioning your BT In Touch 1000 Your BT In Touch 1000 Phone can be positioned in 3 different ways: Please note Make sure you test your phone before you finally fix it in position. • Flat on a table or desk.
Using your phone Making and receiving calls To receive a call To make a call When the phone rings, either: Pick up the handset and speak. Lift the handset and listen for a dialling tone. Press the Handsfree button. Handsfree Dial the number you require.
Redial To make a handsfree call To redial the last number dialled Press the Handsfree button. Handsfree The handsfree light comes on and you can hear the dialling tone. Lift the handset or press the Handsfree Handsfree Dial the number you require. button.
Using the R (Recall) button This button is used with some network services or if your phone line is connected to a switchboard. To find out more about BT Calling Features, please call BT free on 0800 800 150. Quickdial memory To store a number in the Quickdial memory Press Store.
Your BT In Touch 1000 can be positioned in 3 ways: • Flat on a table or desk. Raised Your BT In Touch 1000 can be placed on a table or desk and raised using the base stand. • Raised on a table or desk using the base stand.
WALL PLUG SCREW WALL Wall-mounted Your BT In Touch 1000 can be wall-mounted using the screws and wall plugs provided. Press all the cables coming from the BT In Touch 1000 into their guides on the underside of the unit, Please note as shown below.
Page 15
Rotate the handset hook 180˚ so that you can hang up the handset when the phone is wall-mounted. Hang the holes on the back of the phone over the screwheads and gently pull the phone downward to make sure it is securely in place. Feed the phone line through the bottom of the wall- mounted base stand to allow the cable to rest flat against the wall.
BT In Touch 1000. sequence, confirmed by a flashing orange light on the BT In Touch 1000 and a series of beeps. The BT What to do next In Touch 1000 then dials the first of the allocated Having assessed the situation, the called number emergency contact numbers.
Store Entering your emergency contacts Press the # button. Although the BT In Touch 1000 will accept “999” as a phone number which can be allocated emergency Press the Quickdial memory buttons you status, it is not recommended. BT strongly wish to give emergency status.
They should enter the code 555 on their telephone to accept the emergency call. Failure to enter this code IMPORTANT within 1 minute will cause the BT In Touch 1000 to If you use any Quickdial numbers for a normal call try the alternative emergency numbers.
You have 10 seconds to record a new emergency numbers. announcement message. Release the Announce button on completion The BT In Touch 1000 has a pre-programmed of your message. announcement, which is – Your BT In Touch 1000 will playback “Your “Emergency call, Emergency call.
Store If you hear “Please change batteries” Your BT In Touch 1000 will play back Replace the batteries in the BT In Touch 1000 as “Your emergency announcement is...” and soon as possible. 6 x AA rechargeable batteries are then the original pre-recorded emergency required, see ‘Install the batteries’...
There are two ways to start the emergency sequence on the BT In Touch 1000 – from your BT In Touch The BT In Touch 1000 will beep to confirm that the Pendant and from your BT In Touch 1000 itself.
“Emergency call. Please hang up now”. 00 Optional voice prompts ON. The BT In Touch 1000 will then wait a few seconds 01 Optional voice prompts OFF. and try to start the emergency sequence. If the (Default setting).
Emergency button (on the phone or Pendant). The time can be changed from one to nine seconds in order to help you test your BT In Touch Pendant. To set the contrast of the display To set the emergency cancel timer...
first time, you need to register them to your BT In Touch 1000. The pendant receiver aerial which hangs from the back of your BT In Touch 1000 needs to be uncoiled. Reverse side When attempting to register your BT In Touch...
Page 25
Press and release the Pendant button. Whenever you change the location of the If you have a second BT In Touch Pendant, BT In Touch 1000, you should test the BT In Touch continue holding down the Store button. Pendant again.
Using the BT In Touch Pendant IMPORTANT If the Pendant button is pressed at the same time as a call is coming in, then your BT In Touch 1000 BT In Touch Pendant in normal use will assume that you want to receive the incoming call rather than start the emergency sequence.
If your BT In Touch 1000 needs repair after the warranty period has ended, call the BT In Touch Clean your BT In Touch 1000 with a damp cloth (not Product Helpline on 0845 6011 406 for information wet) or an antistatic wipe. Never use a dry cloth as on our recommended repair agents.
Help and advice If you cannot find the information you require in this section, then phone the BT In Touch Product Helpline on 0845 6011 406 impact on the environment, treat any hazardous No dial tone substances and avoid the increasing landfill.
Technical specification BT In Touch 1000 Radio frequency and bandwidth ....173MHz, 25kHz Power supply ........12V, 500mA Batteries ..........6 x AA rechargeable Standby power........8 hours standby/30 minutes in use Signalling..........Tone Recall key function .......Timed Break Recall Handsfree ...........Simplex Quality Voice Channel (can be switched into simplex mode) Hearing aid compatibility.......Yes...
Need help?
Do you have a question about the IN TOUCH 1000 and is the answer not in the manual?
Questions and answers