Related Manuals for BT CONVERSE 2015
Summary of Contents for BT CONVERSE 2015
- Page 1 This product is intended for connection to analogue public switched telephone networks and private switchboards in the United Kingdom. Converse 2015...
-
Page 2: At A Glance
Please open this page for an ‘At a glance’ guide to your Converse 2015... -
Page 3: At A Glance
Comes on when the data line is being Switch between Hi, Med and Lo. Recall used. Ringer Used to access some BT Select Services and when using your phone with a Calls/Messages light switchboard. Flashes to indicate an incoming call. Also... -
Page 4: Table Of Contents
In this guide Please note that there is a detailed Index at the back of this guide, see page 25. At a glance Using the Converse 2015 PIC PIC program controls Key features Program mode Introduction Fast transfer from PIC to phone... -
Page 5: Key Features
Makes it easy to programme each Converse 2015 with the same stored numbers. Saves time, effort and helps ensure accuracy. Please note that the PIC is available separately. -
Page 6: Introduction
If anything is missing, please contact your place of purchase immediately. Serial number (on the underside of the telephone base): Converse 2015 Converse 2015 base Purchase price: For guarantee purposes, proof of purchase is Handset required, so please keep your receipt. -
Page 7: Safety Information
Do not open the Converse 2015. This could expose you to high voltages or other risks. Contact the Helpline for all repairs. Simply clean your Converse 2015 with a damp (not wet) cloth, or an antistatic wipe. Never use household polish as this may damage the product. -
Page 8: Setting Up
Setting up Situate your Converse 2015 close enough to a phone socket so that the line cord will reach. Your Converse 2015 can be wall-mounted. See ‘Wall-mounting’, on page 22. Plug one end of the coiled cord into the handset... - Page 9 If you have any difficulties setting up or using has taken a voice message for you. For your Converse 2015, please call the BT Converse voice messages the lamp will flash or be 2015 Helpline on permanently on, depending on the type of switchboard it is connected to.
-
Page 10: Using Your Converse 2015
Using your Converse 2015 When the phone rings Pick up the handset. Pick up the handset. Press the button. Press the button. Dial the number. Pick up the handset. Pick up the handset. Press the button. Press the button. The display Press the button. -
Page 11: Hold
Whilst a call is on hold it can be taken come on. on another telephone on the same line. To switch handsfree OFF, press the When it is taken the Converse 2015 will button again. release the line. You can prevent your caller from hearing you while you talk to someone else in the room. -
Page 12: Using The One-Touch Memory
Press the button to confirm. The display shows M1 NUMBER STORED then ENTER NEW NAME. Enter the name you want using the letters on the keypad. This lets you store entries in the For example to enter the name ANNE: one touch memory under the Press once to enter A. -
Page 13: Message Waiting
READ PHONE MEM. Press the button. The display shows SELECT M1 TO M8. If the Converse 2015 is connected to two Press the button you want. telephone lines, Line 2 is used for data The display shows PHONE MEMORY M1. -
Page 14: Using The Converse 2015 Pic
M1-M8 buttons. • Program PIC memory – add/change data stored in the PIC memory. Buttons on your Converse 2015 let you control • Write to phone – copy entire PIC memory functions on the PIC. into the phone. - Page 15 If you make a mistake entering the 4-digit PIN, Insert the PIC into the socket on the try again. top of the Converse 2015. You can try three times. If you still do not enter the correct PIN you should replace the handset and start again.
- Page 16 When you transfer the memory, any entries Press the – if you want to currently stored in the Converse 2015 will see the stored number and name. If no be overwritten. entry is stored, the display shows MEMORY IS EMPTY.
-
Page 17: Fast Transfer From Pic To Phone
This lets you copy the entries from a Converse 2015s. Converse 2015 into the PIC. It takes just 5 seconds to transfer the memory. If a blank PIC is used by mistake, it will not affect any current numbers stored on the phone. -
Page 18: Pic Additional Functions
Release the buttons. Press the button when Press the button when prompted by the display and remove prompted by the display and remove the now blank PIC. the PIC. The Converse 2015 has now been reset to its factory default settings. - Page 19 Insert the PIC into the PIC socket on the Converse 2015. Press and hold the , , and buttons. Now press the button. The display shows PIC RW TEST MODE. Release the buttons. The phone copies entries to the PIC memory, reads them back and then erases them from the PIC.
-
Page 20: General Information
BT Converse 2015 Helpline for assistance: Subject to the terms listed below the guarantee , 9am to 5.30pm, Monday to will provide for the repair of, or at BT’s or its Friday. agent’s discretion, the option to replace the... -
Page 21: Switchboard Compatibility
The Converse 2015 has a REN of 1. Any other instrument provided by BT may be assumed to have a REN of 1 unless otherwise stated. -
Page 22: Help
Check the ringer volume switch at the rear of the base. If necessary set the volume to Hi. Make sure the handset coiled cord is connected properly. If you need further help with your Converse 2015, call the BT Converse 2015 Helpline on... -
Page 23: Wall Mounting
Attach the wall mount to the base by first inserting the hook then pressing in the clips until they lock into place. Before you wall-mount your Converse 2015 check that you are not drilling into any hidden If desk mounted, please see page 8. - Page 24 Cut out this page and place the template on the wall. The location of the screws is indicated by the centres of the crossed lines.
-
Page 26: Index
Index nswer a call ause At a glance access program mode alls delete memory answer fast transfer to phone program controls handsfree program mode hold program PIC memory make read PIC memory receive write to phone redial write to PIC secrecy PIC additional functions Cleaning... - Page 28 44-46 Hung To Road Kwun Tong Kowloon Hong Kong Type of Equipment: Basic Corded Telephone Model No. : Converse 2015 I, the undersigned, hereby declare that the equipment specified above conforms to the above Directive(s) and Standard(s). Place : Hong Kong...
- Page 29 British Telecommunications plc in the UK. © British Telecommunications plc 2002. Registered Office: 81 Newgate Street, London EC1A 7AJ. Registered in England No. 1800000. Converse 2015 Issue 1 (9/02) 4 Designed by The Art & Design Partnership Limited. Printed in China...