Table of Contents
Advertisement
Automatic TV station presetting / Mapping TV stations
Automatic TV station presetting
This VCR has one built-in tuner to receive the
broadcast. Before you record one TV-broadcast,
you must set and preset the whole of the broadcasts.
This VCR can preset up to 80 broadcast.
Automatic station presetting
All stations will be preset in sequence available in your area.
Preparation
Turn on the TV, and select the AV-program position on TV.
1
Press MENU.
Press
repeatedly
until the dot before
CHANNEL SETUP
blinks. Then press
ENTER.
2
Press
repeatedly
until the dot before
AUTO TUNING blink.
3
Press ENTER.
The VCR will begin searching and setting with
early stored channel the number is increased by
one into memory all the broadcasting channels
available in your area (VHF-L, VHF-H, UHF).
While setting channels, AUTO TUNING appears.
When the setting finished, the CHANNEL
MAPPING menu will appear.
AUTO TUNING
4
Press MENU repeatedly until the TV picture
appears on the screen.
To skip a channel position
Unwanted channels can be skipped so that they
cannot be called up by pressing CH. Select the
channel to be skipped, ...e.g. channel 29. Select
channel 29, then press CANCEL.
This channel's number will be flashing. That way you
can cancel further channels one after the other.
To cancel skipping select the skipped channel using
10 number buttons, then press CANCEL. The chan-
nel No. does not blink any longer, and the channel
No. now may be selected again using CH.
Note:
•TV reception interference or power failure may result in
Automatic station presetting malfunctions. In such a
case repeat the setting procedure from the beginning.
However, you can not receive the necessary broadcast
yet, try to preset the broadcast manually.(See page 13)
•When the unit is in the auxiliary input mode, you can not
preset channels.
TIMER REC SET
VCR EXTENSION
or
SHARPNESS
CHANNEL SETUP
SYSTEM SETUP
SELECT :
ENTER : ENTER
EXIT
:
MENU
CHANNEL SETUP
or
CH TUNING
AUTO TUNING
CHANNEL MAPPING
SELECT :
ENTER : ENTER
EXIT
:
MENU
CHANNEL MAPPING
1
5
9
2
6
10
3
7
11
4
8
12
SELECT
:
SKIP
: CANCEL
CHANGE NAME : 1
MOVE
: 2
EXIT
: MENU
Mapping TV stations
Changing TV station names
For a number of TV stations (such as MTV) no name
code will be displayed because these TV stations do
not provide the necessary information. You can
enter the respective names yourself. Moreover,
unwanted station codes can be changed by the user.
Preparation
Turn on the TV, and select the AV-program position on TV.
Exempel: MTV is assigned to station No. 10, but the
code "MTV" will not be displayed and will also not
appear in the table.
1
Select the "CHANNEL MAPPING" in Menu-
screen in the same way as the step 1 ~ 2 on left
side. Then press ENTER.
2
Press
/
/
or
repeatedly until the
station
number
position now to be
named will blink.
• If you want to turn over the page when the
blinking spot is in the left or right edge of on-
screen, press
the next page's 12 stations appears.
3
Press
"1"
of
10
number buttons. The
first display line will
change to "CHANGE
B R O A D C A S T
NAME".
4
Press
or
character appears. Then press
or
to select the next character. Then press
. Up to four
characters can be
used to create a
station name. The
character "
" stands
for a space.
Then press ENTER.
Each press of
display as follows.
A, B, C, ... X, Y, Z
–
5
Press MENU repeatedly until the TV picture
appears on the screen.
Note:
When a wrong character is entered, press CANCEL
and enter the correct character.
CHANNEL MAPPING
1
5
9
2
6
10
3
7
11
4
8
12
SELECT
:
SKIP
: CANCEL
CHANGE NAME : 1
MOVE
: 2
EXIT
: MENU
or
repeatedly until
CHANGE BROADCAST NAME
1
5
9
2
6
10
3
7
11
8
4
12
SELECT :
NAME
:
OK
: ENTER
CLEAR : CANCEL
EXIT
: MENU
repeatedly until the desired
. Use
CHANGE BROADCAST NAME
1
5
9
2
6
10
M
3
7
11
8
4
12
SELECT :
NAME
:
OK
: ENTER
CLEAR : CANCEL
EXIT
: MENU
will change the screen
0, 1, 2, ... 7, 8, 9
+
/
•
11
Advertisement
Table of Contents
