Table of Contents
Advertisement
Remote Control, continued
receivers, and DVD players. Program the remote
control for your equipment and test the keys. See
Appendix C, "Programming the Remote Control."
25.
(PAUSE): Freezes a broadcast TV picture from an
antenna source, cable box, or satellite receiver (if
key has not been reassigned for NetCommand use).
Record/Playback Keys
Use any of these methods to enable the recording and
playback commands of the TV's remote control:
•
Program the remote control for your DVR, VCR, or
DVD player/recorder and set the slide switch to VCR,
DVD, CABLE/SAT, or AUDIO as appropriate.
•
Check HDMI devices for compatibility with the TV's
NetCommand for HDMI feature (see Appendix E).
•
Perform NetCommand IR "learning" for the device.
24.
(RECORD): Records with a VCR or DVR.
25.
(PAUSE): Pauses a VCR, DVR, or DVD. See
above for use during TV viewing.
26.
(STOP): Stops play of a VCR, DVR, or DVD.
27.
(REVERSE): Rewinds a VCR. Reverse scans a
DVR or DVD.
28.
(PLAY): Plays a VCR, DVR, or DVD.
29.
(FORWARD): Fast forwards a VCR. Forward scans
a DVR or DVD.
Note: To operate other audio/video devices using
the TV's remote control:
•
See Appendix C, "Programming the Remote
Control."
•
For HDMI devices compatible with the TV's Net-
Command for HDMI feature, see Appendix E.
•
See chapter 6, "NetCommand IR Control," for
NetCommand IR "Learning" of device keys.
•
For use of specific keys with NetCommand-con-
trolled devices, see "Special Operation Methods,"
page 59.
Resetting the Remote Control
If the slide switch is set to TV and the TV does not
respond properly, reset the remote control.
1.
Press and hold
POWER for several seconds until the
button blinks twice and goes off.
2.
Release the
POWER button.
3.
0 0 9 3 5 and the POWER button will blink
Press keys
twice when you finish entering the code. While
entering the code, pause for a moment between
each key press to ensure it is recognized.
4. TV Operation and Features
Care of the Remote Control
•
Use only alkaline batteries.
•
Be within 20 feet of the equipment.
•
Do not press two or more buttons at the same time
unless instructed to do so.
•
Do not allow unit to get wet or become heated.
•
Avoid dropping on hard surfaces.
•
Do not use harsh chemicals to clean. Use only a soft,
lightly moistened cloth.
•
Do not mix old and new batteries.
Low-Battery Indicator
If you press a key and the POWER key blinks five times,
replace the remote control's batteries.
ChannelView Channel Listings
ChannelView™ displays channel names and program infor-
mation, as sent by broadcasters or your local cable service
provider, for memorized channels on ANT 1 or ANT 2. Listings
may be incomplete. No program information is displayed for
analog channels. An analog channel name is displayed only if
you assigned a name in the Setup > Edit menu (page 47).
To receive ChannelView updates:
•
Keep the Energy Mode set to
•
Set the TV clock
•
Leave the TV powered off for a while each day to
receive updates.
Notes:
-
Listings are updated for the digital channel you are
currently watching.
-
If the time or date displayed are incorrect, change the
TV's time, time zone, date, or Daylight Savaings Time
settings in the Setup menu.
Using ChannelView
Feature
See ChannelView listings
from ANT 1 or ANT 2.
Close ChannelView
Scan channels one by one. Press and hold
Scan channels quickly.
Jump to listings for a
specific channel.
See more of the program
description (if available).
Move navigation to the
program listings.
Move navigation to the
channel listings.
Tune to the highlighted
channel.
Fast Power On
Press Key
Press GUIDE.
Press GUIDE or EXIT.
or
.
Press and hold PAGE
/
1. Enter the channel
number (see numbers in
upper left of screen).
2. Press ENTER.
Press INFO.
Press .
Press .
Press ENTER.
31
.
Hide quick links:
Advertisement
Table of Contents
