Advertisement

Quick Links

GB
Instruction manual for tepan
Model code: C995
Contact Caple on 0844 800 3830 or for spare parts www.4caple.co.uk

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the C995 and is the answer not in the manual?

Questions and answers

Summary of Contents for Caple C995

  • Page 1 Instruction manual for tepan Model code: C995 Contact Caple on 0844 800 3830 or for spare parts www.4caple.co.uk...
  • Page 2 GUIDE TO APPLIANCE 1 Tepan plate 2 Indicators 3 Control for Tepan plate 2 - Indicators 4 In-operation indicator 5 Residual heat indicator...
  • Page 3: Warning And Safety Instructions

    The use of this new equipment is easy. However, we invite you to read this booklet carefully, before installing and using the appliance. This booklet gives the right information on the installation, use and maintenance, as well as useful advice. CAPLE wARNING AND SAFETY INSTRUCTIONS This appliance complies with all relevant local and national safety requirements. Inappropriate use can, however, lead to personal injury and damage to property.
  • Page 4 – it is switched off at the wall socket and the plug is withdrawn from the socket, or it is switched off at the isolator. • Faulty components must only be replaced by genuine Caple original spare parts. The manufacturer can only guarantee the safety of the appliance when Caple replacement parts are used.
  • Page 5: Cleaning For The First Time

    CLEANING FOR THE FIRST TIME • Remove any protective foil and sticky labels. • Clean with a solution of washing up liquid in warm water, and dry with a soft cloth. Metal components have a protective coating which may give off a slight smell when heated up for the first time.
  • Page 6: Cleaning And Care

    OPERATION Tips Wipe the surface of the Tepan plate before each use with a damp cloth to remove any dust particles or other soiling which may have settled on it since it was last used. • Pre-heat the Tepan plate thoroughly for 8 -10 minutes at the power level that you are going to be using for cooking.
  • Page 7: Safety Instructions For Installation

    SAFETY INSTRUCTIONS FOR INSTALLATION • Fit the wall units and extractor hood before fitting the Tepan to avoid damaging the surface. • The veneer or laminate coatings of worktops (or adjacent kitchen units) must be treated with 100 °C heat-resistant adhesive which will not dissolve or distort. Any backmoulds must be of heat-resistant material.
  • Page 8 SAFETY INSTRUCTIONS FOR INSTALLATION Safety distances to the sides of the Tepan Ideally the appliance should be installed with plenty of space on either side. There may be a wall at the rear and a wall or a tall unit at one side. On the other side, however, no unit or divider should stand higher than the appliance.
  • Page 9 SAFETY INSTRUCTIONS FOR INSTALLATION Safety distance when installing the appliance near a wall with additional niche cladding There must be a minimum distance of 50 mm between the niche cladding and the worktop cut-out. This distance is only necessary for niche cladding made of wood or any other combustible material. For non-combustible materials (metal, ceramic tiles or similar), this dimension can be reduced by the thickness of the niche cladding material.
  • Page 10: Preparing The Worktop

    SAFETY INSTRUCTIONS FOR INSTALLATION Preparing the worktop • Make the worktop cut-out for one or more appliances as applicable. Remember to maintain a minimum safety distance from the back wall, as well as from any tall unit or side wall to the right or left of the Tepan.
  • Page 11: Electrical Connection

    After detachment make sure that the grid cannot be reinserted Replacement of the power cable In case of demagement of the power cable, it must be replaced with H 05 VV-F cable type. The replacement need to be installed by a Caple service agent.
  • Page 12 This product complies with EU Directive 2002/96/EC. The crossed-out dustbin symbol reported on the appliance indicates that the appliance must be disposed of separately from other domestic refuse at the end of its useful life. It must therefore be delivered to a waste recycling centre specifically for electric and electronic equipment or returned to the retailer at the moment of purchase of a new equivalent appliance.

Table of Contents