Specifications; Troubleshooting - Gemini CD-110 Operation Manual

CUE INSTRUCTIONS
1. To start the play at a point other than the beginning of a track, follow
these instructions:
First choose the track you wish to play, and then press the PLAY/
PAUSE BUTTON (7) so the unit goes into the play mode. Press the
PLAY/PAUSE BUTTON (7) to pause play at the spot where you want
the play to start the CUE POINT. Use the SCAN BUTTONS (8) to pick
the precise spot you want play to begin, then press the PLAY/
PAUSE BUTTON (7) again to save the cue point. Press the CUE
BUTTON (5) to pause play at the cue point (the unit will go into the
pause mode and the location indicated on the display will be the
memorized cue point). You can preview the cue point by pressing
and holding down the CUE BUTTON (5). Press the PLAY/PAUSE
BUTTON (7) to begin play from the cue point.
2. Once you have saved a cue point you can fine tune or change the
memorized cue point:
To change a cue point, push the PLAY/PAUSE BUTTON (7) so the
unit plays from the cue point, then press the PLAY/PAUSE BUTTON
(7) at the spot you wish your new cue point. Press the PLAY/PAUSE
BUTTON (7) again to save the cue point. The unit will go into the
pause mode and the location indicated on the display will be the new
memorized cue point.
To fine tune a cue point, pause play at the memorized cue point, then
use the SCAN BUTTONS (8) to scan frame by frame (1/75th of a
second) to where you want play to begin. Press the PLAY/PAUSE
BUTTON (7) to save the new cue point.
Note: During fine tuning there will be a stutter effect (to help you
find the beat). The stuttering effect will end when you press the
PLAY/PAUSE BUTTON (7) to save the cue point. Also, during fine
tuning if you hold down the SCAN BUTTONS (8), the unit will
scan quickly after 10 frames.
TROUBLE SHOOTING
• If the disk will not play, check to see if the disc was loaded correctly
(label side up). Also check the disc for excessive dirt, scratches, etc.
• If the disc turns but there is no sound, check the cable connections. If
they are okay, check your amplifier or receiver.
• If the CD skips, check the CD for dirt or scratches. Do not assume
that the CD player is defective. Many CDs are recorded out of spec
and will skip on most or all CD players. Before sending the unit in for
repair, try playing a CD that you are sure plays properly.

SPECIFICATIONS

GENERAL:
Type.................................................Compact
Disc Type............................... Standard Compact discs (12 cm & 8 cm)
Time Display.....................Track Elapsed, Track Remain, or Total remain
Variable Pitch..........................................................................+/- 16%
Pitch Bend..........................................................................+/- 16%
Start....................................................Within
Track Selection....................................................1 to 99 Tracks
AUDIO SECTION:
Quantization......................................1 Bit Linear/Channel, 3 Beam Laser
Oversampling Rate..................................................................8 Times
Sampling Frequency......................................................44.1 kHz
Frequency Response....................................20 Hz to 20 kHz
Digital Output....................................................................IEC958
Total Harmonic Distortion......................................Less Than 0.05%
Signal to Noise Ratio...................................................>96 dB
Dynamic Range.................................................................>94 dB
Output Level (nominal).............................................1.9 Volts R.M.S.
Power Supply......................................AC 120/230V, 60/50 Hz
Dimensions...............................19" x 10.5" x 3.5" (483 x 267 x 90 mm)
Weight....................................................................................9 lbs. (4 kg)
* Specifications and design are subject to change without notice for
purpose of improvement.
Page 4
Disc Player
0.02 seconds