Cutting Accessories - Dremel 4200 Operating/Safety Instructions Manual

* Speed for light cuts; Caution - burning on deep grooves.
Note: Each number settings listed in the speed charts = x 1000 RPMʼs
Catalog Soft
Number Wood
453, 454, 455
Catalog Soft
Number Wood
409, 420, 426
540, EZ409
543, EZ544 25-35
545, EZ545 18-35
560
561 12-35
562
EZ456
EZ476
Catalog Soft
Number Wood
461, 462, 463
414, 422, 429
425, 427
423E
Catalog Soft
Number Wood
403, 404, 405 9-11
428, 442, 443 9-11
530, 531, 532
535, 536, 537 9-11
Catalog Soft
Number Wood
430, 431, 438 5-35
439, 440, 444 5-35
EZ407SA 5-35
407, 408, 432 5-35
EZ411SA, 12-17
EZ412SA, 12-17
12-17
411, 412, 413 12-17
Speed Settings (Continued)
• Depending on cutting direction relative to grain.
Chain Saw Sharpening Stones
Hard Laminates
Wood /Plastic
- -

Cutting Accessories

Hard Laminates
Wood /Plastic
- -
18-35
18-24
For use on drywall. For best results, use at 30,000 rpm.
12-35
- -
- -
- -
Polishing Accessories
Hard Laminates
Wood /Plastic
- -
- -
- -
- -
Hard Laminates
Wood /Plastic
9-11
9-11
- 9-11
9-11
Hard Laminates
Wood /Plastic
5-35 5-17
5-35 5-17
5-35 5-17
5-35 5-17
12-17
12-17
12-17
12-17
Steel Aluminum,
Brass, etc.
- 25-35
Steel Aluminum,
Brass, etc.
5-11 25-35
5-11 -
- -
5-11 -
- -
- 25-35
5-11 -
Steel Aluminum,
Brass, etc.
- 18-24
- 12-17
- 18-24
- 12-24
Wire Brushes
Steel Aluminum,
Brass, etc.
5-11 12-15
5-8 9-11
- 9-11
- 9-11
Steel Aluminum,
Brass, etc.
25-35
25-35
25-35
25-35
5-8 -
5-8 -
5-8 -
5-8 -
23
Shell/
Stone
- -
Shell/
Stone
25-35 25-35
-
- 12-24
25-35 -
- -
25-35 -
- -
Shell/
Stone
18-24 18-24
12-17 12-17
18-24 -
5-8 5-8
Shell/
Stone
5-8 -
9-11 -
- -
9-11 9-11
Shell/
Stone
25-35 5-35
25-35 5-35
25-35 5-35
25-35 5-35
5-8 -
5-8 -
5-8 -
5-8 -
Ceramic Glass
- -
Ceramic Glass
25-35 -
- -
12-24 -
- -
25-35
- -
- -
Ceramic Glass
18-24 18-24
12-17 12-17
- -
5-8 12-24
Ceramic Glass
- -
- -
- -
- -
Ceramic Glass
5-35 -
5-35 -
5-35 -
5-35
- -
- -
- -
- -