Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for CHIEF NW2F8-12
Summary of Contents for CHIEF NW2F8-12
- Page 1 I N S T A L L A T I O N I N S T R U C T I O N S Fixed Wall Racks Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description NW2F8-12...
-
Page 2: Important Warnings And Cautions
Chief® is a registered trademark of Milestone AV Technologies. 150 lbs (68.0 kg) . Use with products heavier than the All rights reserved. - Page 3 Installation Instructions NW2F8-12 DIMENSIONS NW2F818 NW2F1218 DIMENSIONS: INCHES [MILLIMETERS]...
-
Page 4: Installation Instructions
NW2F8-12 Installation Instructions TOOLS REQUIRED FOR INSTALLATION wood stud - 7/32" 5/16" - security 7/16" concrete - 5/16" (included) steel stud - 1/2" PARTS (Model NW2F1218 shown for Parts A, B, C) B (1) C (1) [Door] [Mounting plate] D (4) A (1) 5/16"... - Page 5 Installation Instructions NW2F8-12 SITE REQUIREMENTS (NW2F8-18 and NW2F12-18 Models) - Steel Stud Structure WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! The figure below identifies the minimum requirements for installation of display mounts onto a steel stud structure.
- Page 6 NW2F8-12 Installation Instructions INTRODUCTION The NW2 wall racks have been designed to be mounted onto either a 2" x 4" wood stud (16" on center), concrete, or steel stud wall. (D) x 4 Locate Mounting Site WARNING: IMPROPER INSTALLATION CAN LEAD TO...
- Page 7 Installation Instructions NW2F8-12 Using the mounting plate (C) as a template, mark the wall at the top mounting slots. (See Figure 3) WARNING: ELECTRICAL SHOCK HAZARD! CUTTING Drill one 5/16" pilot hole at both marks made in Step 1. (See...
- Page 8 NW2F8-12 Installation Instructions Hold metal channel on anchor (J) flat alongside plastic Place mounting plate (C) over anchors and align top straps and slide channel through hole. (See Figure 5) mounting holes in mounting plate with holes in anchors. Insert 1/4-20 x 1-3/4" Phillips pan head screws (G) through 1/4"...
- Page 9 Installation Instructions NW2F8-12 Attaching Door Add one end of rack wire (N) to grounding stud at bottom of door. (See Figure ) NOTE: The door may be attached on either the left or right of Tighten 1/4-20 nut (L) onto grounding stud. (See Figure ) the rack.
-
Page 10: Completing Installation
NW2F8-12 Installation Instructions Completing Installation (front view of rack) Hang rack over top rail of mounting plate. (See Figure 13) (inside view of door) Fasten rack from below to mounting plate using two 10-32 x 1/2" security buttonhead screws (K). - Page 11 Installation Instructions NW2F8-12 NOTE: Continue placing items into the rack, moving from the bottom upward. CAUTION: The top of the unit should not be used as a shelf. CAUTION: DISTRIBUTE LOAD CORRECTLY! Load rack with 2/3 total weight of components in the lower half of rack.
- Page 12 Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands P +31 (0)40 2668620 F +31 (0)40 2668615 Chief Manufacturing, a products division Asia Pacific A Office No. 1 on 12/F, Shatin Galleria of Milestone AV Technologies 18-24 Shan Mei Street...
Need help?
Do you have a question about the NW2F8-12 and is the answer not in the manual?
Questions and answers