Clarke XR60 Operating & Maintenance Instructions

Clarke XR60 Operating & Maintenance Instructions

Paraffin/diesel heater

Advertisement

PARAFFIN/DIESEL HEATER
MODEL NO: XR60
PART NO: 6931002
OPERATION & MAINTENANCE
INSTRUCTIONS
LS0813

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the XR60 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Clarke XR60

  • Page 1 PARAFFIN/DIESEL HEATER MODEL NO: XR60 PART NO: 6931002 OPERATION & MAINTENANCE INSTRUCTIONS LS0813...
  • Page 2 INTRODUCTION Thank you for purchasing this CLARKE product. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service.
  • Page 3: Safety Warnings

    SAFETY WARNINGS Your safety is important to you and to others, so please read these instructions before you operate this heater. 1. Failure to comply with the precautions and instructions provided with this heater can result in death, serious bodily injury and property loss or damage from the hazards of fire, explosion, burns, asphyxiation, carbon monoxide poisoning, and/or electric shock.
  • Page 4: Safety Symbols

    SAFETY SYMBOLS The following symbols appear on the unit. Hot Surface, do not High Voltage touch GENERAL PRECAUTIONS VENTILATION Even though this heater operates very close to 100 percent combustion efficiency, it still produces small amounts of carbon monoxide. Carbon monoxide (CO) is toxic. CO can build up in a confined spaces and failure to provide adequate ventilation can be fatal.
  • Page 5: Electrical Connections

    ELECTRICAL CONNECTIONS WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS SUPPLY. Connect the mains lead to a standard, 230 Volt (50Hz) electrical supply through an approved BS1363/A plug fitted with a BS1362 13 amp fuse. If the plug has to be changed because of damage, it must be removed and a replacement fitted, following the wiring instructions shown below.
  • Page 6: Safety Precautions

    SAFETY PRECAUTIONS 1. Check the heater thoroughly for damage. Never operate a damaged heater. 2. Do not modify the heater or operate a heater which has been modified from its original condition. 3. This heater is for indoor use only. 4.
  • Page 7: Filling The Fuel Tank

    NOTE: If you lose the fuel cap a replacement must be obtained before use, this is available from your local Clarke service department part number GF0K070000. 3. Fill the fuel tank with clean diesel or paraffin. • In cold weather, condensation...
  • Page 8: Heater Start Up

    OPERATING INSTRUCTIONS HEATER START UP 1. Make sure power switch is in the OFF position. 2. Turn thermostat to lowest setting. 3. Plug the heater into the mains power supply. 4. Turn the thermostat to highest setting. 5. Start heater by setting the power switch to the ON position.
  • Page 9: Daily Schedule

    MAINTENANCE, STORAGE AND SERVICING WARNING: TO PREVENT PERSONAL INJURY, UNPLUG THE HEATER FROM THE MAINS SUPPLY BEFORE SERVICING. DAILY SCHEDULE GENERAL 1. Make a general visual inspection of the heater for loose or damaged parts. 2. Check nuts and bolts are secure. 3.
  • Page 10 FILTERS Dirty air filters will cause an imbalance in the air-fuel mixture. The best indication that this condition exists is an increase in odour or difficulty getting your heater to ignite. This heater should never be operated without the filters in place.
  • Page 11 NOTE: If the filter is damaged or extremely dirty, a replacement filter of the same type must be fitted, this is available from your local Clarke service department part number GF50K100406. AIR OUTPUT FILTER CLEANING 7.
  • Page 12: Troubleshooting

    1. Check fuel level Check the mains plug is correctly fitted and that the fuse inside it has not blown. 3. Return to Clarke service department for repair. 3 Flashes High limit Make sure heater is cooled down, switch failure 1.
  • Page 13: Wiring Diagram

    WIRING DIAGRAM Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
  • Page 14: Specifications

    SPECIFICATIONS Model XR60 Burn Rate: (Btu/hr.) 50,000 Fuel consumption: 1.6 L/hr. Approx Running Time: 9.4 hr Electrical input: 230V~50Hz Power 166 W Max.Outlet Temp: 1300°F (704°C) Fuel Tank Capacity: 15 L Ignition system: Electric Ignition Primary Safety Control: Flame failure device Weight (kg) 12.45...
  • Page 15: Declaration Of Conformity

    DECLARATION OF CONFORMITY Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...

Table of Contents

Save PDF