Casio 5200 Operation Manual page 3

Operation Guide 5222
Alarm
You can set one Daily Alarm. When the alarm is turned on,
Alarm time
the alarm tone sounds when the alarm time is reached.
(Hour : Minutes)
You can turn on an Hourly Time Signal that causes the
watch to beep twice every hour on the hour.
Pressing D cycles through the available alarm and
hourly time signal combinations (page E-23).
All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C (page E-7).
Alarm on indicator
Hourly time signal
on indicator
E-20
Alarm Operation
The alarm sounds at the preset time for about 20 seconds, regardless of the mode
the watch is in.
Alarm and Hourly Time Signal operations are performed in accordance with the
Timekeeping Mode digital time.
To stop the alarm tone after it starts to sound, press any button.
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
E-22
Alarm On Alarm Off
Signal On Signal Off
The alarm on indicator and hourly time signal on indicator are shown in all modes.
The alarm on indicator fl ashes while the alarm is sounding.
E-24
To measure times with the stopwatch
Elapsed Time
D D D
Start Stop Re-start
Split Time
D A A
Start Split Split release
(SPL indicator
displayed)
Two Finishes
D A D
Start Split Stop
First runner Second runner
fi nishes. Display fi nishes.
time of fi rst
runner.
E-26
To confi gure the countdown timer
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the current
countdown start time starts to fl ash, which indicates the
setting screen.
If the countdown start time is not displayed, use the
procedure under "To use the countdown timer" (page
E-29) to display it.
2. When the setting you want to change is fl ashing, use
and D to change it.
Setting Screen Button Operation
Use D (+) and B (–) to change the setting.
Start Time • You can set a start time in the range of 1 minute to
60 minutes in 1-minute increments.
A to exit the setting screen.
3. Press
E-28
Alarm On Alarm Off
Signal Off Signal On
D A
Stop Clear
D A
Stop Clear
A A
Split release Clear
Display time of
second runner.
B
To set an alarm time
1. In the Alarm Mode, hold down
of the alarm time starts to fl ash, which indicates the
setting screen.
This operation automatically turns on the alarm.
C to move the fl ashing between the hour and
2. Press
minute settings.
3. While a setting is fl ashing, use
change it.
When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (P indicator).
A to exit the setting screen.
4. Press
To turn the alarm and the hourly time signal on and off
1. In the Alarm Mode, you can use
available alarm and hourly time signal combinations as
shown below.
Alarm on indicator
Hourly time signal
on indicator
Stopwatch
The stopwatch lets you measure elapsed time, split times,
Minutes
and two fi nishes.
The display range of the stopwatch is 59 minutes,
59 seconds.
The stopwatch continues to run, restarting from zero after
it reaches its limit, until you stop it.
The stopwatch measurement operation continues even if
you exit the Stopwatch Mode.
Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to elapsed
SPL indicator
time measurement.
Seconds
All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C (page
E-7).
Countdown Timer
The countdown timer can be set within a range of
one minute to 60 minutes. An alarm sounds when the
countdown reaches zero.
All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing C
(page E-7).
Minutes
Seconds
To use the countdown timer
Press D while in the Countdown Timer Mode to start the
countdown timer.
When the end of the countdown is reached, the alarm
sounds for 10 seconds or until you stop it by pressing any
button. The countdown time is reset to its starting value
automatically after the alarm stops.
The countdown timer operation continues even if you exit
the Countdown Timer Mode.
Press D while a countdown operation is in progress to
pause it. Press D again to resume the countdown.
To completely stop a countdown operation, fi rst pause
it (by pressing D), and then press A. This returns the
countdown time to its starting value.
A until the hour setting
D (+) and B (–) to
E-21
D to cycle through the
E-23
E-25
E-27
E-29