Advertisement
Quick Links
MA1010-EA
•
Your watch may differ somewhat from the one shown in the illustration.
Hour hand
Minute hand
24-hour disk
Day
Second hand
To set the day
1.
Pull the crown out to the first click.
2.
Set the day by rotating the crown towards you.
3.
Push the crown back in to the normal position.
•
Avoid changing the date setting while the current time is between 9:00 p.m. and
1:00 a.m.
Using the Stopwatch
Stopwatch minute hand
*
This hand rotates and
indicates the second
count during the first
60 seconds.
The stopwatch lets you measure elapsed time up to 59 minutes, 59.99 seconds.
To measure elapsed time (First 60 seconds)
1.
Press
A to start the stopwatch.
2.
Press
A to stop the stopwatch.
•
You can resume the measurement operation by pressing
3.
Check the elapsed time.
•
The example below shows an elapsed time of 40.30 seconds.
Stopwatch second hand
[40 seconds]
•
Press
B to reset the stopwatch.
This will enter the Timekeeping Mode.
To measure elapsed time (After the first 60 seconds)
1.
Press
A to start the stopwatch.
•
During elapsed time measurement, the stopwatch 1/100 second hand
automatically rotates for the final second of each minute.
2.
Press
A to stop the stopwatch.
•
You can resume the measurement operation by pressing
3.
Press
A and the stopwatch 1/100 second hand will move to the
1/100 second count.
•
If the elapsed time operation was stopped during the final second of each
minute, the stopwatch 1/100 second hand will already be pointing at the
1/100 second count. Do not press A at this time, because doing so will
restart the elapsed time operation.
4.
Check the elapsed time.
•
The example below shows an elapsed time of two minutes, 40.30 seconds.
Stopwatch minute hand
[2 minutes]
Stopwatch second hand
[40 seconds]
•
Press
B to reset the stopwatch.
This will enter the Timekeeping Mode.
Notes:
•
Do not try to perform stopwatch operations while the crown is pulled out either
to the first or second click. If you try to press a button, you might accidentally
cause the crown to rotate and change the current time or day setting.
•
If the starting positions of the stopwatch second hand and 1/100 second hand
become misaligned, use the following procedures to adjust the positions of the
hands so they point to 12 o'clock when the stopwatch is reset.
To adjust the positions of the stopwatch hands
1.
Press
B to reset the stopwatch, and check the alignment of the stopwatch
second hand and 1/100 second hand.
2.
Pull out the crown to the second click.
3.
Press
A to move the stopwatch 1/100 second hand.
4.
If the stopwatch minute hand is aligned correctly, proceed to step 5. If the
stopwatch minute hand is also misaligned, press B to move the stopwatch
second hand.
5.
After making the adjustments you want, push the crown back in to its normal
position.
•
Note that pulling the crown out also stops the timekeeping second hand. After
performing the above procedure, you should also adjust the timekeeping setting.
Operation Guide 5203 5204
To set the time
1.
Pull the crown out to the
second click.
•
At this time, the second
First click
hand will move to the
(Setting Day)
12 o'clock position and
stop there.
2.
Set the hands by rotating the
crown. Rotate the crown to
move the hands clockwise.
Move the minute hand four or
Second click
five minutes past the time you
(Setting Time)
want to set, and then back it
up to the proper setting.
Crown
•
Make sure that you also
(Normal position)
set the 24-hour disk to the
correct hour of the day.
3.
Push the crown back in to
the normal position to restart
timekeeping.
Stopwatch
1/100 second hand
Stopwatch second
hand
A again.
Stopwatch 1/100 second hand
[30]
A again.
Stopwatch 1/100 second hand
[30]
For a watch with an elapsed time bezel
■
Rotate the elapsed time bezel to align the
minute hand.
After certain amount of time elapsed, read the graduation on
the elapsed time bezel which the minute hand points to.
The elapsed time is indicated.
•
Some water resistant models are equipped with a screw
lock crown.
•
With such models, you must unscrew the crown in the
direction noted in the illustration to loosen it before you can
pull it out. Do not pull too forcibly on such crowns.
•
Also note that such watches are not water resistant while
their crowns are loosened. Be sure to screw the crowns
back in as far as they will go after making any setting.
Specifications
Accuracy at normal temperature: ± 20 seconds a month
Display: 3 analog hands (timekeeping hour and minutes, stopwatch 1/100 seconds),
3 dials (timekeeping 24-hour and seconds, stopwatch minutes), day
Stopwatch function: Measuring capacity: 59'59.99"/Measuring unit: 1/100 second
Measuring modes: Elapsed time
Battery: One silver oxide battery (Type: SR927W)
Approximately 2 years on type SR927W (assuming one stopwatch operation 60 min./
day)
mark with the
Elapsed time bezel
1
Advertisement
