Casio 5200 Operation Manual page 2

Operation Guide 5222
Digital Time and Date
Use the Timekeeping Mode to set and view a digital display of the current time and
date. When setting the digital time, you can also confi gure settings for summer time
(Daylight Saving Time or DST), your Home City code (the code for the city where you
normally use the watch), the 12/24-hour format.
This watch is preset with a number of city codes, each of which represents the time
zone where that city is located. When setting the digital time, it is important that you
select the correct city code for your Home City. If your location is not included in the
preset city codes, select the preset city code that is in the same time zone as your
location.
Note that all of the times for the World Time Mode city codes (page E-18) are
displayed in accordance with the digital time and date settings you confi gure in the
Timekeeping Mode.
After you correctly set your Home City time and date, you can set the watch up for
timekeeping with a different city code simply by changing the Home City code in the
Timekeeping Mode.
E-10
C to move the fl ashing in the sequence shown below to select the other
3. Press
settings.
Seconds DST Home City Code
Day Month
E-12
A to exit the setting screen.
5. Press
Resetting the seconds only (without changing the DST, Home City code, hour, or
minute setting) causes the analog minute hand setting to be adjusted automatically.
See "Digital Time Daylight Saving Time (DST) Setting" below for details about the
DST setting.
The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all modes.
Digital Time Daylight Saving Time (DST) Setting
Daylight Saving Time (summer time) advances the digital time setting by one hour
from Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
E-14
Analog Time Setting
Perform the procedure below when the time indicated by the analog hands does not
match the time of the digital display.
To adjust the analog time
1. In the Timekeeping Mode, hold down
seconds until the lower right display fi rst shows H-SET
and then the current digital time starts to fl ash. This is
the analog hand adjustment mode.
D to advance the analog time setting by
2. Press
20 seconds.
Holding down D advances the analog time setting at
high speed.
E-16
World Time
World Time digitally displays the current time in 48 cities
City code
(29 time zones) around the world.
All of the operations in this section are performed in
the World Time Mode, which you enter by pressing C
(page E-6).
To view the time in another city
In the World Time Mode, press D to scroll eastwardly
through city codes.
For full information about city codes, see the "City Code
Current time for the
Table" at the back of this manual.
selected city code
If the current time shown for a city is wrong, it probably
means there is a problem with your Timekeeping
Mode time and/or Home City code settings. Go to
the Timekeeping Mode and make the necessary
adjustments.
E-18
Hour Minutes
Year 12/24-Hour Format
D for about three
To set the digital time and date
1. In the Timekeeping Mode, hold down
seconds start to fl ash, which indicates the setting
screen.
C twice to move the fl ashing to the Home City
2. Press
code setting (page E-12), and then use B and D to
select the code you want.
Make sure you select your Home City code before
changing any other setting.
For full information on city codes, see the "City Code
Table" at the back of this manual.
4. When the setting you want to change is fl ashing, use
described below.
Screen To do this:
Reset the seconds to
Toggle between Daylight Saving Time (
and Standard Time ( )
Change the Home City code
Change the hour or minutes
Toggle between 12-hour ( ) and 24-hour
( ) timekeeping
Change the year
Change the month or day
To toggle the Timekeeping Mode digital time between DST and Standard Time
1. In the Timekeeping Mode, hold down
seconds start to fl ash, which indicates the setting
screen.
C once to display the DST setting screen.
2. Press
D to toggle between Daylight Saving Time
3. Press
( displayed) and Standard Time (
A to exit the setting screen.
4. Press
DST indicator
The DST indicator appears on the Timekeeping Mode
screen to indicate that Daylight Saving Time is turned on.
If you need to advance the analog time setting a long way, hold down D until
the time starts advancing at high speed, and then press B. This locks the
high-speed hand movement, so you can release the button. High-speed hand
movement continues until you press any button. It will also stop automatically
after the time advances 12 hours or if an alarm (daily alarm, Hourly Time Signal,
or countdown beeper) starts to sound.
A to exit the setting screen.
3. Press
The watch will automatically adjust the minute hand slightly to match its internal
second count when you exit the setting screen.
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use
whose Standard Time/Daylight Saving Time setting you
want to change.
A for about one second to toggle between
2. Hold down
Daylight Saving Time (DST indicator displayed) and
Standard Time (DST indicator not displayed).
The DST indicator is on the display whenever you display
DST indicator
a city code for which Daylight Saving Time is turned on.
Note that the DST/Standard Time setting affects only
the currently displayed city code. Other city codes are
not affected.
You will not be able to change the DST/Standard Time setting of the city code
currently selected as your Home City.
Note that you cannot switch between Standard Time and Daylight Saving Time while
is selected as the city code.
A until the
E-11
B and D to change it as
Do this:
Press D.
)
Press D.
Use D (east) and B (west).
Use D (+) and B (–).
Press D.
Use D (+) and B (–).
E-13
A until the
displayed).
E-15
E-17
D to display the city code
E-19