Related Manuals for Kuppersbusch ITE127-9
Summary of Contents for Kuppersbusch ITE127-9
- Page 1 Benutzer- Gebruiksaanwi Notice User manual information jzing d'utilisation Gefrierschrank Vriezer Congélateur Freezer ITE127-9...
-
Page 2: Table Of Contents
Contents Safety information Care and cleaning Control panel What to do if… First use Technical data Daily use Installation Helpful Hints and Tips Environmental concerns Subject to change without notice Safety information In the interest of your safety and to ensure will prevent it from becoming a death trap the correct use, before installing and first us- for a child. - Page 3 • It is dangerous to alter the specifications or cause it to explode, resulting in damage to modify this product in any way. Any dam- the appliance. age to the cord may cause a short-circuit, • Ice lollies can cause frost burns if con- fire and/or electric shock.
-
Page 4: Control Panel
Environment Protection shall be disposed according to the ap- plicable regulations to obtain from your This appliance does not contain gasses local authorities. Avoid damaging the which could damage the ozone layer, in cooling unit, especially at the rear near either its refrigerant circuit or insulation the heat exchanger. -
Page 5: First Use
First use Cleaning the interior Important! Do not use detergents or abra- sive powders, as these will damage the fin- Before using the appliance for the first time, ish. wash the interior and all internal accessories with lukewarm water and some neutral soap so as to remove the typical smell of a brand- new product, then dry thoroughly. -
Page 6: Care And Cleaning
• do not allow fresh, unfrozen food to touch • make sure that the commercially frozen food which is already frozen, thus avoiding foodstuffs were adequately stored by the a rise in temperature of the latter; retailer; • lean foods store better and longer than •... -
Page 7: What To Do If
Defrost the freezer when the frost layer rea- 4. When defrosting is completed, dry the in- ches a thickness of about 3-5 mm. terior thoroughly and keep the scraper for future use. Important! About 12 hours prior to 5. Switch on the appliance. defrosting, set the Temperature regulator 6. -
Page 8: Closing The Door
Problem Possible cause Solution The appliance does not The appliance is switched off. Switch on the appliance. operate. The Pilot light does not flash. The mains plug is not connected Connect the mains plug to the to the mains socket correctly. mains socket correctly. -
Page 9: Technical Data
Technical data Dimension of the recess Height 880 mm Width 560 mm Depth 550 mm Rising Time 20 h The technical information are situated in the rating plate on the internal left side of the ap- pliance and in the energy label. Installation Read the "Safety Information"... - Page 10 Ventilation requirements 2. Adjust the appliance in the niche. The airflow behind the appliance must be The lower hinge cover (in the accesso- sufficient. ries bag) makes sure that the distance between the appliance and the kitchen min. furniture is correct. 200 cm Open the door.
- Page 11 4. Push the sealing strip between the ap- 7. Disconnect the parts (Ha), (Hb), (Hc) and pliance and the adjacent cabinet. (Hd). 5. Remove the correct part from the hinge 8. Install the part (Ha) on the inner side of cover (E).
- Page 12 8 mm 10. Open the appliance door and the kitchen 12. Place the small square on the guide furniture door at an angle of 90°. again and fix it with the screws supplied. Insert the small square (Hb) into guide Align the kitchen furniture door and the (Ha).
-
Page 13: Environmental Concerns
• The magnetic sealing strip is attached Important! If the ambient temperature is low tightly to the cabinet. (for example, in the Winter), the size of the gasket decreases. The size of the gasket increases when the ambient temperature increases. You can also use a hairdryer to increase the size of the gasket.
Need help?
Do you have a question about the ITE127-9 and is the answer not in the manual?
Questions and answers