Cleaning And Maintenance; Key Features - Thane Housewares H2O Mop Ultra SC-393 User Manual

U S E R ' S G U I D E
CAUTION:
Upright storage of the H2O Mop ® Ultra ™ Steamer with a wet Mop Pad may result in the formation of white marks on
your floor. To remove the white marks, clean area with vinegar. Make sure to remove the Mop Pad before storage.
IMPORTANT:
• Always empty the water tank at the end of each use, if any deposits remain in the tank, you can add some water,
swirl it around, cover the cap, shake and empty it. Repeat as needed. DO NOT IMMERSE IN WATER.

CLEANING AND MAINTENANCE

WARNING:
BE SURE THAT THE UNIT IS DISCONNECTED FROM THE POWER OUTLET WHEN
PERFORMING THIS PROCEDURE .
• How to decalcify the water tank interior:
To clean calcium deposits that build up inside the water tank, add one or two tablespoons of white
vinegar to a full water tank, close the water tank cap and shake the contents. DO NOT TURN THE STEAMER ON.
Let it sit for a few hours. Then, empty the water tank and refill with clean water and empty until it rinses clear.
• Cleaning procedure to remove limescale
If your H2O Mop ® Ultra ™ begins to produce steam more slowly than usual or stops producing steam you may need
to remove limescale. Limescale can develop over time on the metal parts and greatly affect the mop performance.
We recommend removing limescale on a regular basis especially in areas with hard water.
The frequency of limescale removal depends upon the hardness of your tap water and how often you use the
steam mop.
To remove limescale from the H2O Mop ® Ultra
By using the Limescale Cleaning Pin (part 24).
1. Make sure that the H2O Mop Ultra is disconnected from the power supply before maintenance.
® ™
2. Remove the hand-held steamer from the main body and the adaptor as
described in How To Use The Hand-Hald Steamer section on page 8.
3. Use the limescale cleaning pin to remove scale deposits from the small hole of
the steam outlet, as illustrated in Fig 1. By swirling and pushing the pin up
and down you will clean the steam outlet. Always ensure that all scale debris
has been removed from the steam outlet before reassembling. Continue
swirling "pin" until no further debris is evident.
4. Attach the Hand-Hald Steamer to the main body.
™ please follow these procedures:
14
U S E R ' S G U I D E
1. Handle
2. ON/OFF Switch on handle
3. Cord Holder
4. Handle Tube
5. Carrying Handle
6. Hand-Held Steamer Release Button
7. Hand-Held Steamer Body Lock
8. H2O Mop
®
9. Water Tank
10. Power Indicator
11. Ready-To-Use Indicator
12. ON/OFF Switch on Hand-Held Steamer
13. Hand-Held Steamer Body
14. Hand-Held Steamer Handle
15. Mop Head locking Clip/Accessory Tray Holder
16. Mop Head
17. Swivel Joint
18. Power Cord
19. Measurement Cup
20. Mop Pad
21. Carpet Glider
22. Short Jet Nozzle
23. Adapter
24. Limescale Cleaning Pin
1. Window Cleaning Kit
2. Fabric Tool
3. Cleaning Cloths
4. Round Brushes (2 nylon and 1 copper)
5. Triangle Brush (nylon)
6. Scoop Nozzle
7. Jet Nozzle
Fig.1
8. Extension Hose
9. Angle Nozzle

KEY FEATURES

Ultra Body
™
10
11
14
12
13
18
22
23
24
ACCESSORY TRAY (CADDY KIT)
(OPTIONAL ITEMS)
3
1
19
2
3
20
4
21
6
7
5
9
8
15
17
16
1
2
3
4
5
9
6
7
8