Channel Setting Mode; Model Select Mode - Kenwood 762G Service Manual

Note :
This mode (self programming mode) cannot be set when
it has been disabled with the FPU.
TX-RX unit B/2
Foil side
D505
4
5
IC505
8 1
The silk screen of D505 and D507 is reversed on the TX-
RX unit PCB (Part No. J72-0677-02). this silk screen will be
corrected from the next version, J72-0677-12.
Fig. 3

8-2. Model Select Mode

• Flow chart
*
Radio type Portable
[CH
[D/A]
/ ]
Radio band & VHF
channel type 8CH
[CH
[D/A]
/ ]
VHF VHF
Frequency
version F1 F2
[CH
[D/A] / ]
[ ]
Self programming mode
[MON] [ ]
Channel set Function set
mode mode
Note :
If the radio type of TK-760G was temporally set to "Por-
table" for the cloning purposes, "UNPROG" is displayed (at
User mode) when the TK-760G is turned on.
In this case, please set the radio type back to "Mobile" at
model select mode menu.
REALIGNMENT
IC502
50
51
*
Mobile
[CH / ]
VHF UHF UHF
128CH 8CH 128CH
[CH [CH
/ ] / ]
[CH / ]
UHF UHF UHF
F1 F3 F4
[CH [CH [CH
/ ] / ] / ]
* *
Cannot be Cannot be
set when set when
portable is mobile is
select. select.
TK-760G/762G

9. Channel Setting Mode

Each channel can be setup in its action mode by using
the panel keys.
• Pressing [MON] when "SELF" is diaplyed, sets channel
setting mode.
• Select an item set using [ ] then change the selection
with the [CH / ].
• The data displayed using [D/A] is stored in the memory
and then proceeds to the next item.
• Pressing [ ] proceeds to the next item without storing it
in the memory.
• Press [MON] to set the display to "SELF" and return to
reset (default) status.
The setup items fro channel setting mode are listed be-
low.
No. Function Choices
Select 1~128 __1-__1._
channel __1-128._
Select 1~128 __1.-__1_
group 128.-__1_
1 RX Step STP__250
frequency 2.5kHz~1MHz STP_1000
Blank - - - - - - - -
100.0000~ R.100.0000 blank switching
550.0000MHz
2 RX Off - - - - - - - -
signalling QT 67.0~250.3Hz QT__67.0_
(EIA mode) QT_250.3_
QT 67.0~250.3Hz QT__67.0*
(0.1Hz step mode) QT_250.3*
DQT 000~777 DQT000N*
(Normal) DQT777N*
(1 step mode)
DQT 023~754 DQT023N_
(Normal) DQT754N_
(Standard table mode)
DQT 000~777 DQT000I*
(Inverse) DQT777I*
(1 step mode)
DQT 023~754 DQT023I_
(Inverse) DQT754I_
(Standard table mode)
Display Remarks
[ ] : Group selection/
Channel selection
change
Display when an item
is selected or when a
step is changed
(about 0.5 seconds)
[A] : Step change
2.5, 5.0, 6.25, 7.5kHz,
1MHz step
[ ] : Frequency on/
The rightmost dot
indicates 50Hz digit
(On=5, Off=0)
[ ] : Off/QT/DQT
switching
[A] : Mode switching
[SCN] : Normal/
Inverse switching
13