Control Operation - Kenwood TS-2000 Instruction Manual

15 OPERATOR CONVENIENCES
Starting Sky Command II+ operation:
After you have completed the following setups, you
can start Sky Command II+ operation. Without
programming these parameters, you cannot perform
Sky Command II+ operation.
On the TS-2000 (Transporter):
1 Select the desired HF frequency that you want to
be controlled on the main transceiver.
2 Select an open VHF frequency in FM mode for the
main transceiver and another open UHF
frequency in FM mode for the sub-receiver.
3 Press [MENU], then turn the MULTI/ CH control to
access Menu No. 62E.
4 Select T-PORTER (Transporter).
5 Press [MENU] to enter the Transporter mode.
On the TM-D700A (Commander):
1 Select the same VHF and UHF frequencies that
you selected for the TS-2000 (Transporter).
2 Access Menu 4–4 to select COMMANDER.
• "PRESS [0] KEY TO START COMMANDER!!"
appears.
3 Press [0] on the DTMF Mic of the TM-D700A to
start the Sky Command II+ operation.

CONTROL OPERATION

After setting up both the TS-2000 (Transporter) and
the TM-D700A (Commander) for Sky Command II+
operation, press Mic [0] on the Commander. While in
Sky Command mode, the Mic keys of the
Commander will function as described below.
Each time you press a key, the Commander will
automatically enter transmit mode and send the
corresponding control command to the Transporter.
T o s w c t i h h t e H F
t a r n c s e v i r e O F F
T o c h a n g e h t e f e r q u e n y c
r o m e m o y r c h a n n l e o n
h t e H F t a r n c s e v i r e
T o t a r n s m t i a u d o i o n a n
H F f e r q u e n y c
T o e r c e v i e a u d o i o n a n
H F f e r q u e n y c
T o m o n t i r o h t e U H F b a n
o n h t e C o m m a n d r e
84
P e r s s M c i [ . ] 1
P e r s s M c i [ U ] P / [ D W N
P e r s s a n d h o d l M c i
P [ T ] T , h t e n s p e a k n i o t
m c i o r p h o n . e
P e r s s M c i [ . ] 2
d P e r s s h t e M c i P F k e y
a s s g i n e d o t h t e M o n t i
u f n t c o i . n
M c i K y e
1 P o w
2 H F
3 M o d
4 R T I
5 X T I
6 R T I
7 S i l p
8 T a r
n I V
9
n I M
0 C r u
B V F O
C I X / T
D I X / T
n I L
1 1 0 H
n I F
n I V
# 2 n I M
e t n y r
1
"FS" appears when you select 1 kHz step (LSB/ USB/ CW) or 10 kHz
step (FM/ AM).
2
After pressing Mic [#], press Mic [0] to [9] to enter a frequency or
memory channel number.
When Mic [0] is pressed, the Commander shows the
current settings of the HF transceiver:
q
e
q HF frequency
w VFO: A, VFO: B,
MR: 00 ~ 99 (memory channel number)
e RIT, XIT
r OFF, –9.99 ~ +9.99
t LSB, USB, CW, FM, or AM
y SPLIT–A: VFO A is used for transmitting.
SPLIT–B: VFO B is used for transmitting.
SPLIT–M: A memory channel is used for transmitting.
u "FS" appears when Mic [
Note:
After pressing [MENU], you can access only Menu 4–4.
The Transporter will transmit its call sign in Morse code every
] .
10 minutes, using the 144 MHz band.
The APO timer will not operate on the transceiver while the
Transporter is ON.
You must set VHF frequency on the main transceiver and UHF
h t e frequency on the sub-receiver. Otherwise, the Sky Command II+
may not operate properly.
When the TS-2000(X) exits the Sky Command II+ operation, the
operating frequency of VFO A will be set to the VHF frequency
that the Sky Command II+ was operated.
r o
F n u i t c n o
r e O F F
f e r q u e n y c e r c e v i e O / N O
l u t a o i n m o d e s w c t i h
O / N O F F
O / N O F F
f o s f t e r o X T I f o s f t e c e l r a
f - t e r q u e n y c O / N O F F
n s e f f r o r m M e m o y r o t V F
F O m o d : e V F O / A V F O
e m o y r R e c l l a m o d : e n o
e r t n s e t t n i g s e r r t e i v e f ( o r
/ M e m o y r R e c l l a m o d e
R T I f o s f e f t e r q u e n y c n i
R T I f o s f e f t e r q u e n y c d e
S , B U S , B r o C W m o d : e
/ z 1 k H z s w c t i h
M r o A M m o d : e 1 k H / z
F O m o d e f : e r q u e n y c e t n
e m o y r R e c l l a m o d : e c h
O N
w
r t y
] is pressed.
F F
O
B s w c t i h
c h a n g e
m H F t a r s n e c v i r e )
s w c t i h
c e r a s e
c e r a s e
1 0 k H z s w c t i h
y r O N
a n n l e n u m b r e
u