Installation; Specifications - Pioneer PRS-D5000SPL Owner's Manual

Connecting the Unit
Four Amplifier Bridged
• Speaker wire size must be 10 AWG minimum.
• Load may be any combination of speakers but impedance must be 4 Ω or larger.
MODE SELECT switch must be in MASTER position.
Connecting wire with
MODE SELECT switch
RCA pin plugs (sold
must be in SYNC INV
separately).
position. Before setting
Connecting
to the position, remove
speaker wire
the screw and the stopper.
(sold separately).
Connecting wire with
MODE SELECT switch
RCA pin plugs (sold
must be in SYNC INV
separately).
position. Before setting
to the position, remove
the screw and the stopper.
Connecting wire with
MODE SELECT switch
RCA pin plugs (sold
must be in SYNC INV
separately).
position. Before setting
Connecting
to the position, remove
speaker wire
the screw and the stopper.
(sold separately).
Four Amplifier
• Speaker wire size must be 10 AWG minimum.
• Load may be any combination of speakers but impedance must be 2 Ω or larger.
MODE SELECT switch must be in MASTER position.
Connecting wire with
RCA pin plugs (sold
separately).
4 Ω
minimum
MODE SELECT switch must
3,000 W
be in SYNC position.
Connecting wire with
RCA pin plugs (sold
separately).
MODE SELECT switch must
be in SYNC position.
Connecting wire with
RCA pin plugs (sold
separately).
MODE SELECT switch must
4 Ω
be in SYNC position.
minimum
3,000 W

Installation

• Do not install the amplifier on unstable places such
CAUTION as the spare tire board.
• The best location for installation differs with the car
• Do not install in:
model and installation location. Secure the amplifier
—Places where it could injure the driver or pas-
at a sufficiently rigid location.
sengers if the vehicle stops suddenly.
• Make temporary connections first and check that the
—Places where it may interfere with the driver,
amplifier and the system operate properly.
such as on the floor in front of the driver's seat.
• After installing the amplifier, confirm that the spare
• Make sure that wires are not caught in the sliding
tire, jack and tools can be easily removed.
mechanism of the seats, resulting in a short-circuit.
• Confirm that no parts are behind the panel when
Example of installation on the floor
drilling a hole for installation of the amplifier. Protect
all cables and important equipment such as fuel lines,
mat or on the chassis
brake lines and electrical wiring from damage.
2 Ω • Install tapping screws in such a way that the
screw tip does not touch any wire. This is important
minimum 1. Place the amplifier where it is to be
to prevent wires from being cut by vibration of the
1,500 W
installed. Insert the supplied tapping
car, which can result in fire.
screws (4 × 18 mm) into the screw
• DO NOT allow amplifier to come into contact
with liquids due to, for example, the location holes. Push on the screws with a
where the amplifier is installed. Electrical shock
screwdriver so they make marks
could result. Also, amplifier and speaker damage,
where the installation holes are to be
smoke, and overheating could result from contact
with liquids. In addition, the amplifier surface and
located.
the surface of any attached speakers could become
hot to the touch and minor burns could result.
2. Drill 2.5 mm (1/8 in.) diameter holes
2 Ω
• To ensure proper installation, use the supplied parts
at the point marked, and install the
minimum in the manner specified. If any parts other than the
supplied ones are used, they may damage internal amplifier, either on the carpet or
1,500 W
parts of the amplifier, or they may become loose
directly to the chassis.
causing the amplifier to shut down.
• Never replace the fuse with one of greater value
or rating than the original fuse. Use of an improp-
er fuse could result in overheating and smoke and
could cause damage to the product and injury
including burns.
2 Ω
CAUTION:
minimum
To prevent malfunction and/or injury
1,500 W
• To ensure proper heat dissipation of the amplifier,
be sure of the following during installation.
—Allow adequate space above the amplifier for
proper ventilation.
—Do not cover the amplifier with a floor mat or
carpet.
• DO NOT allow amplifier to come into contact
with liquids due to, for example, the location
where the amplifier is installed. Electrical shock
2 Ω
could result. Also, amplifier and speaker damage,
minimum
smoke, and overheating could result from contact
1,500 W
with liquids. In addition, the amplifier surface and
the surface of any attached speakers could become
hot to the touch and minor burns could result.

Specifications

Power source .............................................................................................................. 14.4 V DC (10.8 — 15.1 V allowable)
Grounding system ............................................................................................................................................ Negative type
Current consumption .......................................................................................................... 70 A (at continuous power, 4 Ω)
Average current drawn* .......................................................................................................... 10.6 A (4 Ω for one channel)
Fuse ................................................................................................................................................................................ 150 A
Dimensions ........................................................................................................................ 300 (W) × 64 (H) × 330 (D) mm
Weight ...................................................................................................... 7.3 kg (16.0 lbs.) (Leads for wiring not included)
Maximum power output ........................................................................................ 1,500 W × 1 (4 Ω) / 3,000 W × 1 (2 Ω)
Continuous power output .................................................................. 750 W × 1 (at 14.4 V, 4 Ω, 20 —240 Hz 1.0% THD)
Load impedance .................................................................................... 4 Ω (2 — 8 Ω allowable), (Ex. Bridge 4 — 16 Ω)
Frequency response ................................................................................................................ 10 — 240 Hz (+0 dB, –1 dB)
S/N ratio ............................................................................................................................................ 90 dB (IHF-A network)
Distortion .......................................................................................................................................... 0.05 % (50 W, 100 Hz)
Low pass filter .................................................................................................................... Cut off frequency: 40 — 240 Hz
Subsonic filter (HPF) ................................................................................................................................ Frequency: 20 Hz
Bass boost .................................................................................................................................................. Level: 0 — 12 dB
Phase control .......................................................................................................................................... SYNC, SYNC INV
Gain control ................................................................................................................................................ 200 mV — 6.5 V
Maximum input level / impedance ........................................................................................................ RCA: 6.5 V / 22 kΩ
Power output ........................................................................................ 750 W RMS × 1 channel
Tapping-screws
(4 × 18 mm) S/N ratio .............................................................................. 60 dBA (Reference: 1 W into 4 Ω)
Note:
• Specifications and the design are subject to possible modification without notice
due to improvements.
*Average current drawn
• The average current drawn is nearly the maximum current drawn by this unit
when an audio signal is input. Use this value when working out total current
drawn by multiple power amplifiers.
Floor mat
or chassis
Drill a 2.5 mm (1/8 in.)
diameter hole
15.6 A (2 Ω for one channel)
[12 (W) × 3 (H) × 13 (D) in.
1,500 W × 1 (at 14.4 V, 2 Ω, 20 —240 Hz 2.0% THD)
Cut off slope: –18, –24 dB/oct
Slope: –18 dB
Frequency: 40 — 120 Hz
(4 Ω and
1 % THD+N)
1500 W RMS × 1 channel
(2 Ω and
1 % THD+N, 240 Hz)