Advertisement
ASSEMBLY INSTRUCTIONS CONT.
Step 4: Align the flat of the shaft with the securing screw
on the fan blade and slide the fan blade onto
the shaft with the securing screw facing the rear
grill.
Step 5: Center the front grill by aligning the GE Brand
logo on the logo plate so it is upright and
straight. Then, holding the front grill against the
rear grill snap each clip forward onto the front
grill.
Final Assembly
Step 1: First, slide the inner pole up from the outer pole.
Insert the Pole Lock Knob into the hole on the
outer pole, to securely hold this position. Next,
place the fan head assembly into the inner pole,
inserting the neck of the fan into the pole open
ing. Turn the fan head's neck until the head is
securely locked into place. Finally, add the Tilt
Adjustment Knob to the hole of the fan head's
neck. Tighten when fan head is in the desired
position.
OPERATING INSTRUCTIONS
Step 1: Set the fan base on a dry, level surface.
Step 2: Please make sure the On/Speed switch is in the
"Off" position. Plug the cord into any standard
120-volt A/C outlet.
Step 3: The SPEED is adjusted by moving the switch left
or
right to the desired setting.
Step 4: The OSCILLATION knob is located on
the top of the fan motor housing. To start oscilla-
tion, push control knob down. To stop oscillation,
pull control knob up.
A.) Front Grill
B.) Fan Blade
C.) Securing Screw
D.) Rear Grill Mounting-Ring
E.) Rear Grill
F.) Motor Shaft
G.) Motor Housing
H.) Tilt Adjustment Knob
I.) Inner Pole
J.) Pole Lock Knob
K.) Outer Pole
L.) Pole Ring
M.)Base
N.) Weighted Insert
O.) Washer
P.) L Shaped Locking Lever
Q.) Grill Clips (6)
Q
C
D
F
A
B
E
ADJUSTMENT INSTRUCTIONS
Tilt Adjustment
Step 1: To change the tilting angle of the fan head, sim-
ply loosen the Tilt Adjustment Knob.
Step 2: Move the fan head to the desired angle, and then
firmly tighten the knob to lock the fan head in
place.
Height Adjustment
Step 1: Turn the Pole Lock Knob counter clockwise to
loosen the inner pole.
Step 2: Adjust the inner pole to the desired height, and
firmly tighten the pole lock knob in a clockwise
direction.
WARNING: Make sure to support the fan head
assembly when loosening the adjustable height
knob, as the weight of the fan head may cause the
inner pole to collapse.
CLEANING/MAINTENANCE
INSTRUCTIONS
Follow these instructions to correctly and safely care for
your GE Brand stand fan. Please remember:
• Always unplug the fan before cleaning or disassem-
bling.
• Do not allow water to drip on or into the fan motor
housing.
• Do not use any of the following as a cleaner: gasoline,
thinner, benzine.
(See instructions for fan head assembly)
Step 1: To access the fan blade, remove the front grill
and then unscrew the securing screw on the fan
blade.
Step 2: Clean the fan blade, both front and rear grills
with a soft cloth moistened with a mild soap solu-
tion.
Step 3: Replace blade, tighten the fan blade by screwing
the fan blade back on, and securely fasten the
front grill.
Fan Head, Base, and Pole Cleaning
G
Using a soft, moist cloth, with or without a mild soap solu-
H
tion, carefully clean the fan base, pole, and head. Please
use caution around the motor housing area. Do not allow
I
the motor or other electrical components to be exposed
to water.
J
FAN STORAGE
K
L
Your fan can be stored in the off-season either partially
M
disassembled or assembled. It is important to keep it in a
safe, dry location.
• If stored disassembled, we recommend using the origi-
N
nal (or appropriately sized) box.
• If stored assembled or partially assembled, remember
O
P
to protect the fan head from dust.
Advertisement
