GE Profile PDW8100 Series Installation Instructions Manual page 13

TM
PDW9700JII – GE Profile
Built-In Dishwasher Dimensions (in inches)
24 †††
24
22-1/2
33-13/16" MIN.
adj. to 35"
21-1/4
4 (Adjustable)
2-3/4
†††
Add 3/4" for custom panel and additional room
for custom handle
Electrical Rating
Voltage AC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Hertz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Total connected load amperage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.1
Calrod ® heater watts max. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 875
For use on adequately wired 120-volt, 15-amp circuit having 2-wire service
with a separate ground wire. This appliance must be grounded for
safe operation.
Specification Created 7/03
250202
™ Fully Integrated Built-In Dishwasher
Installation Information (in inches)
Hot
water
line on
left
27-1/2
Dishwasher Rough-In Information
Note: Dishwasher must not be installed more than ten feet
from sink for proper drainage. All plumbing and electrical
work must be in accordance with local codes.
Note: If a flush look is needed, a 25" base cabinet needs
to be used (except Profile and Triton XL models).
The power cord and connections must comply with the
National Electrical Code Section 422 and/or local codes
and ordinances. The cord must be no longer than six feet
from the junction box to the receptacle.
Countertop
This wall area
must be free of
90
pipes or wires
24"
4 4
MIN.
4
5 5
34" to 34-3/4"
6 6
Underside
of countertop
to floor
Plumbing and electrical
2
service must enter
inside shaded area
19" MIN. from wall 24" From wall
24" MIN.
Listed by
Underwriters
R
Laboratories
For answers to your Monogram,
GE ®
As an ENERGY STAR ® partner,
GE has determined that this product GEAppliances.com or call
meets the ENERGY STAR ®
GE Answer Center
guidelines for energy efficiency.
Custom Panel for Model PDW9700JII
Dishwasher comes panel-ready.
Custom
Countertop
Panel Size
90
Cabinets
Electrical
Side
wiring is
A
3" from
View
cabinet
Electrical
wiring on
Floor
right
3/4" Max.
Bottom of
Adjacent Cabinetry
The most common panel dimensions are 30-1/4"H
and 23-3/4"W.
STEP A: Determine custom panel height
1. Measure Dimension A from underside of
countertop to bottom of adjacent cabinets.
2. Subtract 1/4". This allows a 1/4" clearance gap
between the underside of the countertop and
the top of the dishwasher door.
Height is equal to A minus 1/4"
STEP B: Determine custom panel width
1. Measure dimension B, the rough opening width.
2. Subtract 1/4" for clearance (1/8" on each side).
Width is equal to B minus 1/4"
Note: 23-1/8" min. panel width and 26-1/4" min.
panel height is required to cover the door frame.
Panel height varies depending on installation.
Consideration must be given to door swing
clearance above the toekick.
® GE Profile ™
appliance questions, visit our website at
® service, 800.626.2000.
B
or