Related Manuals for KitchenAid KSRF42DT
Summary of Contents for KitchenAid KSRF42DT
- Page 1 42” Built-h Refrigerator Model KSRF42DT IMPORTANT: Installer: Leave Installation instructions with the Homeowner. Homeowner: Keep Installation Instructions for future reference. Save Installation Instructions local electrical inspector’s use.
-
Page 2: Tools And Materials Needed For Installation
Three colors of acrylic door panel Location of the built-in refrigerator kits are available from your must permit the doors to open to KitchenAid dealer: White, Black at least 900. and Almond. Each kit includes door Because of the weight and size of... - Page 3 Dimensions for built-in area Electrical outlet Width and depth of the built-in area should be centered are determined by the type of within shaded area installation. The built-in refrigerator can be installed with the doors flush with the wall, with the doors rounded electrical protruding from the wall, or with side panels enclosing refrigerator.
-
Page 4: Product Dimensions
*-See page 5.4 The 8-l /2” top grille is provided. Height dimensions Smaller top grilles must be ordered when the from your KitchenAid dealer. Check maximum the chart below for the part numbers extension levelers (l-114” you need to order for the size of top below rollers) grille you need. - Page 5 Custom door panels, handle inserts and top grille panels Panel touting for door Refrigerator door panel and top grille panels. Door and top grille panels: 1 -I Dimensions shown are with routed 114” max. 4-22-314”.-b edges. Routing is required if panels are more than l/4”...
- Page 6 Product dimensions +I- WY tolerance b-42” protruding door installation -5132” Side trim Refrigerator .&hen 25” depth is available. If completed according to each less than 25” depth is available, site’s restrictions. go to step 3. One method is to attach side If side panel is not inserted into panel to outside of side trim.
-
Page 7: Electrical Requirements
Electrical Water supply 3. Ground electric drill or use a hand drill. Drill a 3/l 6” hole in vertical requirements requiremkds cold water line. Attach a saddle valve to the water line with a Use only l/4” copper tubing for clamp in an easily accessible water line. -
Page 8: Product Support
Product support wood block(s) A solid soffit or a wood block is required to prevent the refrigerator Block(s) must be long enough from tipping forward after it is to fully cover installed. width of cover. Determine what height the refrigerator will be when it is Important: Block(a) must... - Page 9 Now start... Move refrigerator to kitchen. Place cardboard Remove top grille assembly or plywood under Personal Injury Hazard package, literature package reffigerator. Remove appliance and parts bag taped to the Because of the weight and dolly. Open doors and remove all refrigerator door and save.
- Page 10 3-prong grounding type wall receD!acle side trim, Move refrigerator close to Remove tape from rear L .,. _ final position. Remove leveling rods. Turn the two cardboard or plywood from leveling rods clockwise using a 5/l 6” under refrigerator. Plug electrical socket and ratchet until the cabinet cord into the grounded outlet.
- Page 11 (Consult your your KitchenAid ’ Use builder to adjust countertops.) and Care Guide. Keep To adjust vertically: Loosen, do Ins talla tion Ins true tions...
- Page 12 Use and Care Guide unsatisfactory, contact the Customer Relations Department, KitchenAid, Inc., P.O. Box 558, St. Joseph, Ml 490850558. Call Toll Free 800-422-l 230. Part No. 1113201 Rev.A Prepared by KitchenAid ’ Printed in U.S.A. St. Joseph, Michigan 49085 0 1989 KitchenAid...