HP 5400 zl Installation And Getting Started Manual

HP 5400 zl Installation And Getting Started Manual

5400 zl series
Hide thumbs Also See for 5400 zl:
Table of Contents

Advertisement

HP 5400 zl Switches
Installation and Getting Started Guide
Power over Ethernet

Advertisement

Table of Contents
loading

Summary of Contents for HP 5400 zl

  • Page 1 HP 5400 zl Switches Installation and Getting Started Guide Power over Ethernet...
  • Page 3 HP 5400 zl Switches Installation and Getting Started Guide...
  • Page 4 HP 12-port Gig-T / 12-port SFP v2 zl Module J9637A HP 5412 zl-96G Switch J8700A HP 5406 8p 10GBASE-T 8p 10GbE SFP+ v2 zl Switch with Premium Software J9866A HP 5412 zl-96G-PoE+ Switch J9448A HP 5412-92G-PoE+/2XG-SFP+ v2 zl Switch with Premium Software...
  • Page 5: Table Of Contents

    Overview of HP 5400 zl Switches ........
  • Page 6 1. Prepare the Installation Site ....... . 2-6 Cabling Infrastructure ........2-6 Installation Location .
  • Page 7 HP networking tools ........
  • Page 8 Downloading New Software ........5-14 HP Customer Support Services ........5-14 Before Calling Support .
  • Page 9 C Safety and Regulatory Statements Safety Information ..........C-1 Informations concernant la sécurité...
  • Page 11: Introducing The Hp 5400 Zl Switches

    Introducing the HP 5400 zl Switches The HP 5400 zl switches include the 5406 zl switch, 5412 zl switch and their bundles. They are multiport modular switches that provide Layer 3 routing features, and also feature low latency for high-speed networking.
  • Page 12: Overview Of Hp 5400 Zl Switches

    Overview of HP 5400 zl Switches Overview of HP 5400 zl Switches HP 5406 zl Switches The HP 5406 zl switch is available as an open 6-slot chassis (J9642A) with Premium Features activated. The HP 5406zl-48G switch bundle (J8699A) ships with the 5406 zl 6-slot chassis without Premium Features and the following: •...
  • Page 13: Hp 5412 Zl Switches

    • With Premium Features activated HP 5412 zl Switches The HP 5412 zl switch is available as an open 12-slot chassis (J9643A) with Premium Features activated. The HP 5412zl-96G switch bundle (J8700A) ships with the 5412 zl 12 slot chassis without Premium Features and the following: •...
  • Page 14 Introducing the HP 5400 zl Switches Overview of HP 5400 zl Switches See “Switch Accessories” on page 1-17 for a list of the switch modules that can be installed in the HP 5400 zl switches.
  • Page 15: Hp 5406 Zl Switch

    Overview of HP 5400 zl Switches HP 5406 zl Switch The HP 5406 zl switch ships with the 5400 zl Management Module and open, 6-slot chassis (J9642A). The switch needs at least one power supply to operate. The 5406 zl switch bundles are not shown.
  • Page 16: Hp 5412 Zl Switch

    Overview of HP 5400 zl Switches HP 5412 zl Switch The HP 5412 zl switch ships with the 5400 zl Management Module and open, 12-slot chassis (J9643A). It does not ship with any power supplies. The switch needs at least one power supply to operate. The 5412 zl switch bundles are not shown.
  • Page 17: Network Connectivity, Speeds And Technologies

    Introducing the HP 5400 zl Switches Network Connectivity, Speeds and Technologies Network Connectivity, Speeds and Technologies These products support optional network connectivity as follows: Table 1-1. Optional Network Connectivity, Speeds and Technologies Transceiver Form-Factor and Connector Speed Technology Cabling SFP ("mini-GBIC")
  • Page 18: Front Of The Switch

    Switch Modules and slots with Link and Mode LEDs for each port located on each module Figure 1-3. Front of 5406zl-48G Switch This illustration shows the 5406zl-48G (J8699A), but the labeling and descrip- tions apply to all of the HP 5400 zl switches.
  • Page 19: Leds

    Introducing the HP 5400 zl Switches Front of the Switch LEDs As described in the next two tables, there are LEDs on the switch chassis and on the switch modules that keep you informed of the status of the switch and the network connections.
  • Page 20 Introducing the HP 5400 zl Switches Front of the Switch LEDs State Meaning Blinking If Flash, Fault, and Self Test LEDs are blinking, Compact Flash failed self-test. If Flash and Fault LEDs are blinking, an operational fault has occurred. If fast blinking (400ms On and 400ms Off), an operational alert occurred and is unresolved (for example, the Compact Flash is not present).
  • Page 21 Introducing the HP 5400 zl Switches Front of the Switch LEDs State Meaning Modules (green - A module is installed in the switch module slot corresponding to the letter and the module letters is undergoing or has passed self test. This also occurs when you install a module when corresponding to the switch is already powered on (“hot swap”).
  • Page 22: Led Mode Select Button And Indicator Leds

    To optimize the amount of information that can be displayed for each of the switch ports, the 5400 zl switches use a Mode LED for each port. The operation of this LED is controlled by the LED Mode Select button on the switch chassis, and the current selection is indicated by the mode indicator LEDs near the button.
  • Page 23 Introducing the HP 5400 zl Switches Front of the Switch Mode LEDs LED Mode Select button (one for each port) and indicator LEDs Figure 1-4. Mode LEDs and LED Mode Select Button If the Activity indicator LED is lit, each port Mode LED displays ■...
  • Page 24: Console Port

    This port is used to connect a console to the switch by using the serial cable supplied with the switch. This connection is described under “Connecting a Console to the Switch” in chapter 2, “Installing the 5400 zl Switches”. The console is a full-featured interface that can be used to configure, monitor, and troubleshoot the switch.
  • Page 25: Back Of The Switch

    Figure 1-6. Back of a 5412 zl switch with two power supplies Power Connector The Series 5400 zl Switches do not have a power switch; they are powered on when connected to an active AC power source. The 5400 zl switches automat-...
  • Page 26: Redundant Power Supply

    J8712A, a Switch zl 1500 W Power Supply J8713A, or a Switch zl 1500 W PoE+ Power Supply J9306A) can be installed in the back of the 5400 zl switches. To provide redundancy, each power supply should be connected to different AC power sources.
  • Page 27: Switch Accessories

    Introducing the HP 5400 zl Switches Switch Accessories Switch Accessories Accessories of the 5400 zl switches include a 6 or 12-slot chassis for installing any of the available zl Modules. The supported zl modules include: ■ 24-Port 10/100/1000 PoE+ zl Module (J9307A) ■...
  • Page 28 Introducing the HP 5400 zl Switches Switch Accessories To view or download this guide, visit www.hp.com/networking/support. 1-18...
  • Page 29: Switch Features

    Switch Features The features of the 5400 zl switches include: N o t e Some of the listed 5400 zl switch features require a Premium License. ■ modules can be installed in any order and in any combination and can the “hot swapped”...
  • Page 30 Management and Configuration Guide which is on the HP networking Web site. ■ support for IEEE 802.3af standard, IEEE 802.3at standard, and pre-standard PoE devices.
  • Page 31: Installing The Hp 5400 Zl Switches

    Installing the HP 5400 zl Switches The 5400 zl switches are easily installed. They come with an accessory kit that includes the brackets for mounting the switch in a standard 19-inch telco rack, or in an equipment cabinet. The switches have rubber feet already attached so they can be securely located on a horizontal surface.
  • Page 32: Accessory Kits

    Installing the HP 5400 zl Switches Included Parts Accessory Kits 5406 zl Accessory Kit (5069-8561) 5412 zl Accessory Kit (5069-8562) two mounting brackets two mounting brackets - these brackets are twice as long as the brackets for the 5406 zl switches...
  • Page 33: Installation Procedures

    HP Switch zl modules. Some of the 5406 zl and 5412 zl switches come with preinstalled modules. Depending on where you will install your 5400 zl switch, it may be easier to install the modules first. The modules are “hot swappable” though, so they can also be installed and removed after the switch is powered on.
  • Page 34: Installation Precautions

    At this point, the switch is fully installed. See the rest of this chapter if you need more detailed information on any of these installation steps. Installation Precautions Follow these precautions when installing your 5400 zl switch: W A R N I N G ■...
  • Page 35: Installation Precautions (Continued)

    Installation Procedures Installation Precautions (continued) C a u t i o n s If the switch is to be shipped in a rack, use only an HP 10000 series rack ■ and a rail mounting kit (5070-0145) for each switch.
  • Page 36: Prepare The Installation Site

    C a u t i o n Make sure you install only HP Switch zl Modules. Avoid any electrostatic discharge problems by handling the modules only by their bulkheads.
  • Page 37 Installing the HP 5400 zl Switches Installation Procedures ■ Once the module is fully inserted, screw in the two retaining screws to secure the module in place. The screws should be tightened until they are secure, but not overtightened. If you do not use one or more of the slots, ensure the slot cover plate is ■...
  • Page 38: Installing A Management Module Battery

    Installing the HP 5400 zl Switches Installation Procedures Use the extractor handles to seat the module completely. Then tighten the retaining screws on the module until they are secure, but do not overtighten them. Figure 2-1. Generic chassis with module fully installed...
  • Page 39 Installing the HP 5400 zl Switches Installation Procedures Installing a New Battery. Figure 2-2. Battery location on Management Module Insert the new battery with the lettering and the plus “+” sign facing up. Install the management module into the switch.
  • Page 40: Optional) Install Another Power Supply

    Power Supply (J8712A), an HP Switch zl 1500 W Power Supply (J8713A), or an HP Switch1500 W PoE+ Power Supply (J9306A) can be installed in the back of the switch. The 5406 zl switch can hold up to two power supplies and the 5412 zl switch can hold up to four power supplies.
  • Page 41 Installing the HP 5400 zl Switches Installation Procedures C a u t i o n The switch power supplies are hot swappable; they can be installed while the switch is receiving power from the supply in the other slot. But, as indicated by the caution statement on the power supply, the supply must not be connected to AC power before being installed or removed.
  • Page 42: Verify The Switch Passes Self Test

    Installing the HP 5400 zl Switches Installation Procedures tighten the four screws Figure 2-4. Back of switch with power supply fully installed 4. Verify the Switch Passes Self Test After you have installed any modules and the optional second power supply,...
  • Page 43 Installation Procedures N o t e The 5400 zl switches do not have a power switch. They are powered on when the power cord is connected to the switch and to a power source. If your installation requires a different power cord than the one supplied with the switch, please see the “Installation Precautions”...
  • Page 44: Led Behavior

    Rack or Cabinet Mounting The 5400 zl switches are designed to be mounted in any EIA-standard 19-inch telco rack or in an equipment cabinet such as a server cabinet. If you are installing the switch in an equipment cabinet, read the following “Equipment Cabinet Note”...
  • Page 45 For the 5406 zl switches, each bracket is attached with four screws as shown in the following illustration. Although these procedures show the 6-slot chassis, the procedures are the same for the 12-slot chassis. 8 mm M4 screws Figure 2-7. Attaching brackets to the 5400 zl switch 2-15...
  • Page 46 Installing the HP 5400 zl Switches Installation Procedures Partially install a screw into the top hole of a pair of holes that are 0.5 inches apart in each rack/cabinet upright as shown in the illustration below. Ensure that the screws are at the same level in each upright.
  • Page 47: Horizontal Surface Mounting

    Installing the HP 5400 zl Switches Installation Procedures Install the other screw into the upper hole in each bracket. Tighten these screws. install and tighten the other 12-24 screws Figure 2-10. Screws in bracket being installed Horizontal Surface Mounting Place the switch on a table or other horizontal surface. Use a sturdy surface in an uncluttered area.
  • Page 48: Connect The Switch To A Power Source

    Grounding lug screws Grounding lug Figure 2-11. Attaching grounding lug to the 5400 zl switch 7. Connect the Switch to a Power Source Plug the included power cord into the switch’s power connector and into a nearby properly grounded AC power source.
  • Page 49: Eps Operation

    Installation Procedures The HP Switch zl Power Supply Shelf, (J8714A), hereafter referred to as the EPS, is an accessory product for the 5400 zl switches. The EPS provides External Power-over-Ethernet (PoE) or PoE+ power for up to two 5400 zl switch products.
  • Page 50: Power Supply Shelf Leds

    Installing the HP 5400 zl Switches Installation Procedures Power Supply Shelf LEDs The EPS LEDs are duplicated on the front and back of the device. The following graphic shows an example of the front of the EPS. There are two...
  • Page 51: Connect The Network Devices

    9. Connect the Network Devices The type of network connections you will need to use depends on the types of switch modules you have installed in your 5400 zl Switch. See the documen- tation accompanying the modules for cabling configurations and procedures for those modules.
  • Page 52: 10. (Optional) Connect A Console To The Switch

    • Verify you have used the correct cable type for the connection: – for all twisted-pair connections, the RJ-45 connectors on the 5400 zl switches allow you to use either straight-through cable or crossover cable when the port is in the “Auto” configuration.
  • Page 53: Terminal Configuration

    Out-of-band: Connect a PC or VT-100 terminal, to be used as a console, directly to the switch using the serial cable that comes with the 5400 zl switches. If the PC or terminal has a 25-pin serial connector, you can use a readily available 9-pin to 25-pin serial cable, or attach a 9-to-25 pin straight-through adapter to the PC end of the cable.
  • Page 54: Direct Console Access

    Installing the HP 5400 zl Switches Installation Procedures Direct Console Access To connect a console to the switch, follow these steps: Connect the PC or terminal to the switch’s Console Port using the console cable included console port with the switch. (If your...
  • Page 55: Telnet Console Access

    TELNET session, see chapter 3, “Getting Started With Switch Configuration” for some basic configuration steps. For more detailed information, refer to the Management and Config- uration Guide which is on the HP networking Web site. 2-25...
  • Page 56: Hot Swapping Switch Modules

    Installing the HP 5400 zl Switches Hot Swapping Switch Modules Hot Swapping Switch Modules The switch modules can be “hot swapped” (except for the Management Module, it is not hot swappable), that is installed or replaced while the switch is powered on (See Module Installation Notes on page 2-6).
  • Page 57: Example Network Topologies

    Installing the HP 5400 zl Switches Example Network Topologies Example Network Topologies This section shows a few example network topologies in which the 5400 zl switches can be implemented. Although these examples show the 6-slot chassis, the principles are the same for the 12-slot chassis.
  • Page 58: Use As An Edge Switch

    Figure 2-18. Edge switch configuration When your network expands and the users need to access resources beyond the edge of the local network, the 5400 zl switches are excellent platforms for that expansion. With the flexibility of 6 slots, the high port count 10/100/1000-...
  • Page 59: Optimizing The 10-Gbe Port Configuration

    Example Network Topologies Optimizing the 10-GbE Port Configuration The 10-GbE ports on the HP 5400 zl switch are designed to deliver full 10 Gbps wire-speed to each port, where either one or two ports are in a linked state with another device. When three or four 10-GbE ports are in a linked state, when using an X2 (J8708A), CX4 (J8707A) or SFP+ (J9309A) module, the 10- GbE ports support an aggregate bandwidth of 28.8 Gbps across the linked...
  • Page 60: Optimizing The 10-Gbe Port Configuration With Version 2 Zl Modules

    2 zl modules The 10-GbE Module (J9538A) is designed to deliver additional performance for zl switches. The 5400 zl has a fabric design that allows for optimal performance with 10GbE v2 zl modules. When compared to the first genera- tion zl modules, the bandwidth channels have been improved to a maximum capacity of 23.4 Gbps per channel, as opposed to 14.4 Gbps channels for the...
  • Page 61 Figure 2-21. Version 2 optimized 10-GbE port configuration The 5400 zl can send 32 Gbps per module with 64 byte packets. This allows for an oversubscription for the HP 8-port 10-GbE SFP+ v2 zl Module (J9538A) on the 5400 zl, or 2 wire rate 10GbE ports.
  • Page 63: Getting Started With Switch Configuration

    ProCurve Manager. For a listing of switch features available with and without an IP address, refer to “How IP Addressing Affects Switch Operation” in the Management and Configuration Guide which is on the HP networking Web site.
  • Page 64: Using The Switch Setup Screen

    DHCP or Bootp server. To use DHCP/Bootp instead of the manual method described in this chapter, see “DHCP/Bootp Operation” in the Management and Configuration Guide which is on the HP networking Web site. Using the Switch Setup Screen...
  • Page 65 Press Enter, then S (for Save). The following is information on the fields in the Setup screen. For more information on these fields, see the Management and Configuration Guide which is on the HP networking Web site. Parameter Default System Name blank Optional;...
  • Page 66: Where To Go From Here

    5400 zl switches, please see the Management and Configuration Guide which is on the HP networking Web site. To Recover from a Lost Manager Password: If you cannot start a con-...
  • Page 67: Using The Ip Address For Remote Switch Management

    Using the IP Address for Remote Switch Management With your 5400 zl switches, you can use the switch’s IP address to manage the switch from any PC that is on the same subnet as the switch. You can use either a Telnet session or a standard web browser to manage the switch.
  • Page 68 Figure 3-2. Switch Web Browser Interface - Status Overview For more information on using the web browser interface, please see the Management and Configuration Guide which is on the HP networking Web site. An extensive help system is also available for the web browser interface. To...
  • Page 69: Configuring The Hp Wireless Edge Services Zl Modules (J9051A, J9052A)

    Wireless Services zl Module (J9052A) must be running software version WT.01.xx or later. N o t e The term ‘module’ is used in this section to refer to both the HP Wireless Edge Services zl Module (J9051A) and the HP Redundant Wireless Services zl Module (J9052A).
  • Page 70 Getting Started With Switch Configuration Configuring the HP Wireless Edge Services zl Modules (J9051A, J9052A) ■ To display the module’s IP address, enter: HP(wireless-services-id)# show ip interfaces The following example enters the wireless-services context of a module installed in Slot B of a zl switch and then displays the IP address assigned by...
  • Page 71: Configuring Vlans On The Zl Switch

    For more information on configuring and managing configuration files on an external FTP or TFTP server, see the HP Wireless Edge Services zl Modules www.hp.com/networking/ Management and Configuration Guide, available at...
  • Page 72: Configuring Wireless Lan Services

    Guide for information on using the Web browser interface to configure and manage a module. To run the Web browser interface for the HP Wireless Edge Services zl Module, your workstation must be running Java Virtual Machine (JVM). If your workstation is not running the JVM and you attempt to open the module’s Web browser interface, the workstation will automatically try to...
  • Page 73: Replacing Components

    For a complete list of parts and part numbers, see page 2-1. H o t S w a p p i n g The HP 5400 zl Switch supports “hot swapping” - the ability to replace the following hardware components while the switch is operating: a fan tray, power supply (if a second power supply is installed), interface module.
  • Page 74: Replacing Power Supplies

    Replacing Power Supplies Replacing Power Supplies If your HP E5400 zl Switch is configured with redundant power supplies, you will not suffer any loss of traffic or performance if a power supply fails. Replace the failed component as soon as possible. One of the Internal Power LEDs on the management module will blink simultaneously with the switch Fault LED indicating which power supply failed.
  • Page 75 Figure 4-2. Power supply installation Tighten the four retaining screws that hold it in place. Be careful not to overtighten the screws. For more detail refer to the HP Switch zl Internal Power Supply Installation Guide (5991-3787).
  • Page 76: Replacing Fan Trays

    Replacing Components Replacing Fan Trays Replacing Fan Trays When a fan fails the Fan Status LED on the switch chassis will blink simultaneously with the switch Fault LED. In this case, the entire fan tray needs to be replaced. You cannot replace individual fans. The fan tray is hot swappable.
  • Page 77: Replacing The Management Module

    The switch does not have to be powered off to remove the management module, however when the management module is removed all ports will lose communication. HP networking recommends replacing all components during scheduled down time. To install (or replace) a Management Module: 1.
  • Page 78: Replacing The Management Module Compact Flash Card

    Replacing Components Replacing the Management Module Compact Flash Card Replacing the Management Module Compact Flash Card The Compact Flash card is the primary non-volatile storage medium located on the management module that contains both the boot software and configuration files. When a Flash card fails the CF status LED on the management module will blink simultaneously with the switch Fault LED.
  • Page 79: Replacing The J9289A One Services Zl Module Compact Flash Card

    Replacing Components Replacing the J9289A ONE Services zl Module Compact Flash Card Replacing the J9289A ONE Services zl Module Compact Flash Card The Compact Flash card is the primary non-volatile storage medium located on the Services Module that contains both the boot software and configuration files.
  • Page 80: Replacing The J9289A One Services Zl Module Disk Drive

    Replacing Components Replacing the J9289A ONE Services zl Module Disk Drive Replacing the J9289A ONE Services zl Module Disk Drive The disk drive is the primary non-volatile storage medium located on the Services Module that contains both the boot software and configuration files. When a disk drive fails the “HDD status”...
  • Page 81: Troubleshooting

    Troubleshooting This chapter describes how to troubleshoot your 5400 zl switches. Note that this document describes troubleshooting mostly from a hardware perspective. You can perform more in-depth troubleshooting using the software tools available with the switch, including the full-featured console interface, the built-in web browser interface, and ProCurve Manager, the SNMP-based network management tool.
  • Page 82: Basic Troubleshooting Tips

    Data path loops will cause broadcast storms that will severely impact your network performance. With your 5400 zl switches, if you wish to build redundant paths between important nodes in your network to provide some fault tolerance, you should enable Spanning Tree Protocol support on the switch.
  • Page 83 ■ Connecting to devices that have a fixed full-duplex configuration. The RJ-45 ports on the 5400 zl switches are all configured as “Auto”. That is, when connecting to attached devices, the switch will operate in one of two ways to determine the link speed and the communication mode (half duplex or full duplex): •...
  • Page 84: Diagnosing With The Leds

    Troubleshooting Diagnosing with the LEDs Diagnosing with the LEDs Table 5-1 shows LED patterns on the switch and the switch modules that indicate problem conditions. Check in the table for the LED pattern you see on your switch Refer to the corresponding diagnostic tip on the next few pages. Table 5-1.
  • Page 85: Diagnostic Tips

    Switch gl module and should not be used in your zl switch. that corresponds to Ensure you have installed a zl module in the slot. HP xl/gl modules will fit the letter that is in the slot, but they are not compatible with your HP zl switch. Check to blinking is an ensure the module has a Blue “zl module”...
  • Page 86 As HP networking introduces new modules for your HP Switch zl, you may have to update the switch with new operating code that supports the new module. The documentation that came with the module will indicate which version of the operating code is needed to support the module.
  • Page 87 Reconnect the power supply to the AC power source. If the error indication reoccurs the slot after the supply is reinstalled, the power supply may be faulty. Call your HP corresponding to authorized LAN dealer, or use the electronic support services from HP networking the blinking to get assistance.
  • Page 88 • Verify you have used the correct cable type for the connection. – for any of the twisted-pair connections, in the default configuration (Auto), either a straight-through or a crossover cable can be used and the switch will automatically adjust its operation. See the “HP Auto-MDIX Feature” description on page B-7 for more information.
  • Page 89: Hp Networking Tools

    The console interface is also accessible through a telnet connection. See the “Troubleshooting” chapter in the Management and Configuration Guide for more information on using these software tools to diagnose and manage your switch, which is on the HP networking Web site. See page 5-1 details.
  • Page 90: Hardware Diagnostic Tests

    Replacing a module with the same type of module. ■ Methods of Resetting the Switch You can reset the switch by any of these methods: pressing the Reset button. On the 5400 zl switches, this is the Reset button ■ on the Management Module. ■...
  • Page 91: Testing The Switch By Resetting It

    Troubleshooting Hardware Diagnostic Tests Testing the Switch by Resetting It If you believe the switch is not operating correctly, you can reset the switch to test its circuitry and operating code. To reset a switch, either: ■ Unplug and plug in the power cord (power cycling) ■...
  • Page 92: Testing Twisted-Pair Cabling

    IEEE 802.3 Type 10Base-T, 100Base-TX, or 1000Base-T standards, as appropriate for the switch port type that the cable is connected to. The twisted-pair cables attached to the 5400 zl switches must be compatible with these standards.To verify your cable is compatible with these standards, use a qualified cable test device.
  • Page 93: Restoring The Factory Default Configuration

    For both the save and restore processes, you can use the console copy command. See the switch Management and Configura- tion Guide which is on the HP networking Web site. See page 5-1 for details.
  • Page 94: Downloading New Software

    Troubleshooting Downloading New Software Downloading New Software When product enhancements occur for the 5400 zl switches, new software can be downloaded to the switch through several methods, for product enhance- ments and new features. Please see the Management and Configuration Guide which is on the HP networking Web site.
  • Page 95: Physical

    Weight: • 5406 zl Switch base system(J8697A) 10.68 kg (23.55 lbs) • 5412 zl Switch base system(J8698A) 15.86 kg (34.95 lbs) Electrical The HP zl Power Supply Specfications:. J8712A J8713A AC voltage: 100-127 volts 200-240 volts 200-240 volts Maximum current:...
  • Page 96: Environmental

    Specifications Environmental Operating Non-Operating Temperature: 0C to 55C (32F to 131F) -40C to 70C (-40F to 158F) Relative humidity: 15% to 80% at 55C (131F) 15% to 90% at 65C (149F) (non-condensing) Maximum altitude: 3.1 km (10,000 ft) 4.6 km (15,000 ft) If you are installing either the J8705A, J8707A, or J9289A modules, or any of the X2 transceivers, the operating ambient temperature for the switch should not exceed 40C (104F).
  • Page 97: Safety

    Specifications Safety ■ EN60950 CSA 22.2 No. 60950 ■ ■ UL 60950 IEC 60950 ■ Technology Standards and Safety Compliance Table A-1. Technology Standards and Safety Compliance Laser safety information Technology Compatible EN/IEC SFP+ Media with these IEEE standard ("mini-GBIC") Lasers Lasers Converter...
  • Page 98 Specifications Table A-1. Technology Standards and Safety Compliance (Continued) Laser safety information Technology Compatible EN/IEC SFP+ Media with these IEEE standard ("mini-GBIC") Lasers Lasers Converter standards compliance Lasers Lasers 1000-BX IEEE 802.3ah EN/IEC 60825 Class 1 Laser 1000BASE-BX10 Product Laser Klasse 1 10-Gig CX4 IEEE 802.3ak 10GBASE-CX4...
  • Page 99: B Cabling And Technology Information

    Cabling and Technology Information Cabling and Technology Information Specifications Table B-1. Cabling Specifications 10 Mbps Operation Category 3, 4 or 5, 100-ohm unshielded twisted-pair (UTP) or shielded twisted-pair (STP) cable, complying with IEEE 802.3 10BASE-T specifications. 100 Mbps Operation Category 5, 100-ohm UTP or STP cable, complying with IEEE 802.3u 100BASE-TX specifications.
  • Page 100 For 10GBASE-T, Category 6 patch cables are sensitive to movement once link has been established, and could cause link to drop if moved. Therefore HP recommends using Category 6A patch cables, or using cable management options to tie down (dress) the Category...
  • Page 101: Technology Distance Specifications

    Cabling and Technology Information Technology Distance Specifications Table B-2. Technology Supported cable type Multimode fiber Supported distances modal bandwidth 100-FX multimode fiber up to 2,000 meters 100-BX single mode fiber 0.5 - 10,000 meters 1000-T twisted-pair copper up to 100 meters 10GBASE-T twisted-pair copper Cat 6 unshielded - up to 55 meters...
  • Page 102 Cabling and Technology Information Table B-2. Technology Supported cable type Multimode fiber Supported distances modal bandwidth 10-Gig ER single mode fiber 2 - 40,000 meters CX4 Media Converter 12-strand female-female multi- 150 MHz*km 1 - 50 meters mode fiber MPO ribbon cable 500 MHz*km 1 - 100 meters with MTP connectors, in a...
  • Page 103: Mode Conditioning Patch Cord

    Cabling and Technology Information Mode Conditioning Patch Cord Mode Conditioning Patch Cord The following information applies to installations in which multimode fiber- optic cables are connected to a Gigabit-LX port or a 10-Gigabit LRM port. Multimode cable has a design characteristic called “Differential Mode Delay”, which requires the transmission signals be “conditioned”...
  • Page 104 Cabling and Technology Information Mode Conditioning Patch Cord Gigabit-LX port To network multimode Mode Conditioning cabling Patch Cord Single mode section plugs into Tx The multimode cable in the patch cord port on Gigabit-LX Transceiver or must match the characteristics of your Gigabit-LX transceiver network cable Figure B-1.
  • Page 105: Twisted-Pair Cable/Connector Pin-Outs

    IEEE 802.3ab standard. HP Auto-MDIX and the IEEE 802.3ab Auto MDI/ MDI-X feature are completely compatible. If you connect a 5400 zl Switch twisted-pair port to another switch or hub, which typically have MDI-X ports, the 5400 zl Switch port automatically operates as an MDI port.
  • Page 106 Cabling and Technology Information Twisted-Pair Cable/Connector Pin-Outs ■ For 10 Mbps connections to the ports, you can use Category 3, 4, or 5 100-ohm differential unshielded twisted-pair (UTP) or shielded twisted- pair (STP) cable, as supported by the IEEE 802.3 10Base-T standard. For 100 Mbps connections to the ports, use Category 5 100-ohm differen- ■...
  • Page 107: Straight-Through Twisted-Pair Cable For 10 Mbps Or 100 Mbps Network Connections

    Straight-Through Twisted-Pair Cable for 10 Mbps or 100 Mbps Network Connections Because of the HP Auto-MDIX operation of the 10/100 ports on the switches, for all network connections, to PCs, servers or other end nodes, or to hubs or other switches, you can use straight-through cables.
  • Page 108: Crossover Twisted-Pair Cable For 10 Mbps Or 100 Mbps Network Connection

    Crossover Twisted-Pair Cable for 10 Mbps or 100 Mbps Network Connection The HP Auto-MDIX operation of the 10/100 ports on the switches also allows you to use crossover cables for all network connections, to PCs, servers or other end nodes, or to hubs or other switches.
  • Page 109: Straight-Through Twisted-Pair Cable For 1000 Mbps Network Connections

    Cabling and Technology Information Twisted-Pair Cable/Connector Pin-Outs Straight-Through Twisted-Pair Cable for 1000 Mbps Network Connections 1000Base-T connections require that all four pairs or wires be connected. Cable Diagram Figure B-4. Straight-through Cable Diagram for 1000 Mbps Network Connection N o t e Pins 1 and 2 on connector “A”...
  • Page 111: C Safety And Regulatory Statements

    Safety and Regulatory Statements Safety Information Documentation reference symbol. If the product is marked with this symbol, refer to the product documentation to get more information about the product. WARNING A WARNING in the manual denotes a hazard that can cause injury or death.
  • Page 112: Informations Concernant La Sécurité

    Safety and Regulatory Statements Informations concernant la sécurité Informations concernant la sécurité Symbole de référence à la documentation. Si le produit est marqué de ce symbole, reportez-vous à la documentation du produit afin d'obtenir des informations plus détaillées. WARNING Dans la documentation, un WARNING indique un danger susceptible d'entraîner des dommages corporels ou la mort.
  • Page 113: Hinweise Zur Sicherheit

    Safety and Regulatory Statements Hinweise zur Sicherheit Hinweise zur Sicherheit Symbol für Dokumentationsverweis. Wenn das Produkt mit diesem Symbol markiert ist, schlagen Sie bitte in der Produktdokumentation nach, um mehr Informationen über das Produkt zu erhalten. WARNING Symbol für Dokumentationsverweis. Wenn das Produkt mit diesem Symbol markiert ist, schlagen Sie bitte in der Produktdokumentation nach, um mehr Informationen über das Produkt zu erhalten.
  • Page 114: Considerazioni Sulla Sicurezza

    Safety and Regulatory Statements Considerazioni sulla sicurezza Considerazioni sulla sicurezza Simbolo di riferimento alla documentazione. Se il prodotto è contrassegnato da questo simbolo, fare riferimento alla documen- tazione sul prodotto per ulteriori informazioni su di esso. WARNING La dicitura WARNING denota un pericolo che può causare lesioni o morte.
  • Page 115: Consideraciones Sobre Seguridad

    Safety and Regulatory Statements Consideraciones sobre seguridad Consideraciones sobre seguridad Símbolo de referencia a la documentación. Si el producto va marcado con este símbolo, consultar la documentación del producto a fin de obtener mayor información sobre el producto. WARNING Una WARNING en la documentación señala un riesgo que podría resultar en lesiones o la muerte.
  • Page 116: Informações De Segurança

    Safety and Regulatory Statements Informações de Segurança Informações de Segurança Símbolo de referência à documentação. Se o produto estiver marcado com este símbolo, consulte a documentação do produto para obter mais informações sobre ele. AVISO Um AVISO no manual indica um perigo que possa causar ferimentos ou morte.
  • Page 117: Safety Information (Japan

    Safety and Regulatory Statements Safety Information (Japan) Safety Information (Japan)
  • Page 118: Safety Information (China

    Safety and Regulatory Statements Safety Information (China) Safety Information (China)
  • Page 119: Emc Regulatory Statements

    Safety and Regulatory Statements EMC Regulatory Statements EMC Regulatory Statements U.S.A. FCC Class A This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against interference when the equipment is operated in a commercial environment.
  • Page 120: Japan

    Switches are assigned a Regulatory Model Number. The Regulatory Model Number for these switches is RSVLC- 0503. This regulatory number should not be confused with the marketing name (HP 5400 zl Switches), or product numbers (J8697A, J8698A, J8699A, and J8700A). C-10...
  • Page 121: European Community

    Hewlett-Packard Company 8000 Foothills Blvd., Roseville, CA 95747 U.S.A. Supplier's Address: declares, that the product Product Name and Model: HP E5406zl Switch, HP E5412zl Switch HP E8206zl Switch, HP E8212zl Switch J8697A, J8699A, J9447A, J8698A, J8700A, J9448A J9475A, J9477A, Product Number(s):...
  • Page 122 Safety and Regulatory Statements EMC Regulatory Statements C-12...
  • Page 123: D Recycle Statements

    Recycle Statements Waste Electrical and Electronic Equipment (WEEE) Statements Disposal of Waste Equipment by Users in Private Household in the European Union This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste.
  • Page 124 Recycle Statements Waste Electrical and Electronic Equipment (WEEE) Statements Laitteiden hävittäminen kotitalouksissa Euroopan unionin alueella Jos tuotteessa tai sen pakkauksessa on tämä merkki, tuotetta ei saa hävittää kotitalousjätteiden mukana. Tällöin hävitettävä laite on toimitettava sähkölaitteiden ja elektronisten laitteiden kierrätyspisteeseen. Hävitettävien laitteiden erillinen käsittely ja kierrätys auttavat säästämään luonnonvaroja ja varmistamaan, että...
  • Page 125 Recycle Statements Waste Electrical and Electronic Equipment (WEEE) Statements Smaltimento delle apparecchiature da parte di privati nel territorio dell'Unione Europea Questo simbolo presente sul prodotto o sulla sua confezione indica che il prodotto non può essere smaltito insieme ai rifiuti domestici. È responsabilità dell'utente smaltire le apparecchiature consegnan- dole presso un punto di raccolta designato al riciclo e allo smaltimento di apparecchiature elettriche ed elettroniche.
  • Page 126 Para obter mais informações sobre locais que reciclam esse tipo de material, entre em contato com o escritório da HP em sua cidade, com o serviço de coleta de lixo ou com a loja em que o produto foi adquirido.
  • Page 127 … B-7 Act LED … 1-10 crossover cable pin-out … B-10 auto MDI/MDI-X operation … B-9, B-11 HP Auto-MDIX feature … B-7 HP Auto-MDIX feature … B-7 MDI-X to MDI connections … B-9, B-11 auxiliary or USB port MDI-X to MDI-X connections …...
  • Page 128 … 2-19 redundant power supply … 1-15, 2-11 operation … 2-19 resetting the switch for new module type … 2-26 EPS (PoE) power … 2-18 switch modules … 2-26 HP Auto-MDIX feature description … B-7 2 – Index...
  • Page 129 … 2-1 behavior during self test … 2-14 installation Power Status … 1-9 5400 zl Switches … 2-1 behavior during self test … 2-14 connecting the switch to a power source … 2-18 showing error conditions … 5-4 horizontal surface mounting …...
  • Page 130 … 4-4 ports flash memory card … 4-5, 4-6, 4-7 console … 2-23 Reset button HP Auto-MDIX feature … B-7 description … 1-13 network connections … 2-21 location on switch … 1-7, 1-13 power connector … 1-14 restoring factory default configuration … 5-13...
  • Page 131 … B-9, B-11 telnet access to the console … 2-25, 3-5 switch-to-computer connection … B-9, B-11 terminal configuration … 2-23 switch-to-switch or hub connection … B-10 testing … 5-12 twisted-pair ports HP Auto-MDIX feature … B-7 Index – 5...
  • Page 132 VT-100 terminal serial cable connection for … 2-24 wireless edge services wireless modules … 3-7 wireless module backup process … 3-9 wiring rules for twisted-pair cables … B-7 6 – Index...
  • Page 134 To learn more, visit www.hp.com/networking/support © Copyright 2005, 2013 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services.

This manual is also suitable for:

5406 zl5412 zl

Table of Contents