Table of Contents
Advertisement
PLL TUNING ADJUSTMENT
Note: PLL Tuning must be adjusted after IC101 (Signal
Processor), IC802 (EEPROM) or T151 (PLL VCO Coil)
is replaced.
1. Disconnect the AC power cord (120V AC line).
2. While pressing the MENU key, reconnect the AC power
cord. The Service Menu display will now appear.
3. Select NO. 04 PT (PLL Tuning) with
4. Adjust the data to 64 with + or – key.
5. Disconnect the AC power cord (120V AC line).
6. Connect voltmeter + lead to TP113 on main board and
– lead to main board ground.
7. Press and Hold the POWER key on the front control panel
while connecting the AC power cord. TV will turn on.
8. Disconnect the antenna terminal and select a good
quality active color channel in your area, using keys 0 ~
9 on the remote control. Wait a few seconds, and then
reconnect the antenna terminal.
9. Turn PLL VCO coil (T151) on main board fully clockwise,
and then gradually turn the coil counterclockwise until
voltage is at the maximum level (approximately 6.7
VDC). Continue to turn the coil counterclockwise until
the voltage is at the minimum level (approximately 0.7
VDC), and then turn the coil clockwise until voltage indi-
cates 3.8 ± 1.0 VDC. Voltage change in the coil
adjustments is shown in Figure 6.
10. Disconnect voltmeter from chassis.
Select every active channel with keys 0 ~ 9 and the scanning
keys, and check to be sure the AFT is operating properly.
Figure 6. Voltage Change in Coil Adjustment
RF-AGC ADJUSTMENT
1. Tune receiver to strongest VHF station in your area.
2. Set contrast and brightness controls for maximum.
3. Turn off the receiver and disconnect the AC power cord
(120V AC line).
4. While pressing the MENU key, reconnect the AC power
cord. The Service Menu display will now appear.
5. Select NO. 03 RAD (RF-AGC Delay) with
6. Adjust the data with + or – key in the direction which
causes snow to appear; then in the opposite direction
until the snow just disappears.
7 . To turn off the Service Menu display, press the MENU key.
BRIGHTNESS LEVEL ADJUSTMENT
Note: Grayscale, RF-AGC, Video Level and High Voltage Check
must be adjusted before attempting Brightness Level
Adjustment.
1. Connect a color-bar generator to the antenna terminals.
2. Switch the generator to the crosshatch pattern.
3. Reset the picture controls to the Sports levels.
4. Connect voltmeter (high impedance) + lead to terminal
5. Turn off the receiver and disconnect the AC power cord
6. While pressing the MENU key, reconnect the AC power
7. Select NO. 25 SB (Sub Brightness) with
or
key.
8. Adjust the data with + or – key for 820mVDC.
9. Press the MENU key to turn off the Service Menu display.
10. Check brightness level on every active channel, readjust
Note: Do not set to excessive brightness level, otherwise
HIGH VOLTAGE HOLD-DOWN TEST
Every time the receiver is serviced, the HIGH VOLTAGE
HOLD-DOWN circuit must be tested for proper operation by
following these steps:
1. Connect receiver to 120V AC line. Tune receiver to active
channel. Reset the picture controls to the News levels.
2. Check that the voltage measured between TP7 and TE7
(ground side) is within 16.5 VDC to 21 VDC. If the voltage
is out of this range, the Hold-Down Circuit must be checked.
3. Connect a DC Voltage supply to TP7 and TE7 through a
100 ohm 1/4W resistor. Adjust the DC voltage to 23 VDC.
The receiver should shutdown, losing raster and sound.
Then the receiver should turn off automatically. This
reaction indicates that the Hold-Down circuit is function-
ing properly. If the receiver does not shutdown, a
malfunction is indicated and its cause must be found and
corrected.
4. To obtain picture again, remove the DC Supply and wait
a few minutes. Now turn on the receiver.
HIGH VOLTAGE CHECK
Note: +B (+130V) Voltage Check and Grayscale Adjustment
1. Connect high voltage voltmeter negative lead to ground,
and connect + lead to anode of picture tube.
2. Tune receiver to an active channel and confirm TV is
operating properly.
3. Eliminate the beam current by adjusting the contrast and
brightness controls to minimum.
4. Confirm high voltage is within 29.0 KV and 31.0 KV. If
reading is not within range, check horizontal circuit.
or
key.
No high-voltage adjustment is provided on this chassis.
SOUND ADJUSTMENT
1. Connect Voltmeter – lead to ground and + lead IC101 Pin
50 (FM DET OUT).
2. Tune receiver to an active channel and fine tune to obtain
the best picture.
3. Confirm D.V.M. reading of 3.85 ± 0.2 VDC.
4. I f the voltage is out of this range, adjust Sound I.F.
Transformer (T131) for 3.85 ± 0.2 VDC.
— 7 —
TP51 and – lead to terminal TP50 on main board. Set
voltmeter for 1.5V ~ 3V range.
(120V AC line).
cord. The Service Menu display will now appear.
(repeat steps 5 ~ 9) if necessary).
the contrast level will be suppressed.
must be completed before attempting High Voltage
Check.
or
key.
Hide quick links:
Advertisement
Table of Contents
