Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Bosch LTC 9385 Series
Summary of Contents for Bosch LTC 9385 Series
- Page 1 LTC 9385 Series Instruction Manual EN Outdoor Housings...
-
Page 2: Important Safeguards
EN | 2 LTC 9385 Series | Instruction Manual | Important Safeguards Important Safeguards 1. Read, Follow, and Retain Instructions - All safety 10. Power Sources - Operate the unit only from the type and operating instructions should be read and of power source indicated on the label. -
Page 3: Safety Precautions
EN | 3 LTC 9385 Series | Instruction Manual | Safety Precautions Safety Precautions For Indoor Product 1. Water and Moisture - Do not use this unit near water - for example, in a wet basement, in an unprotected outdoor installation or in any area classified as a wet location. -
Page 4: Precauciones De Seguridad
EN | 4 LTC 9385 Series | Instruction Manual | Safety Precautions Sécurité Sicherheitshinweise ATTENTION : POUR ÉVITER TOUT RISQUE D'ÉLECTROCUTION, VORSICHT: UM EINEN ELEKTRISCHEN SCHLAG ZU N'ESSAYEZ PAS DE RETIRER LE CAPOT (OU LE PANNEAU VERMEIDEN, IST DIE ABDECKUNG (ODER RÜCKSEITE) NICHT ARRIÈRE). - Page 5 EN | 5 LTC 9385 Series | Instruction Manual | Safety Precautions Medidas de Segurança Sicurezza CUIDADO: PARA REDUZIR O RISCO DE CHOQUE ATTENZIONE: PER RIDURRE IL RISCHIO DI SCOSSE ELETTRICHE NON RIMUOVERE LA COPERTURA (O IL ELÉCTRICO, NÃO RETIRE A TAMPA (OU A PARTE PANNELLO POSTERIORE).
-
Page 6: Table Of Contents
EN | 6 LTC 9385 Series | Instruction Manual | Contents Table of Contents Important Safeguards ..............2 UNPACKING . -
Page 7: Unpacking
0.4mm (0.016in.) plastic spacer 4.1.1 NEMA-3R and IP54 Nylon bushings The LTC 9385 Series housings include a breather hole in 3/8in. NPT plug the front face plate. The breather hole prevents the Small flex fitting accumulation of moisture inside the housing when Pull Seals installed in areas of high humidity. -
Page 8: Tools Required
EN | 8 LTC 9385 Series | Instruction Manual | Installation Input Power Cord - European 5.2 Tools Required • Flat blade screwdriver Cable Type H05RN-F3G0.75 and H05RN-F3G1.00 • Phillips head screwdriver • M7 (7mm) hex wrench or socket Cable Size Outside diameter between 4.3mm... -
Page 9: Camera/Lens Installation
EN | 9 LTC 9385 Series | Instruction Manual | Installation 3. Remove the cover from the base assembly by Camera/Lens Installation grasping the cover and gently pulling forward. Place the camera/lens combination onto the rail Do not remove the safety cable from the cover assembly. -
Page 10: Camera/Lens Wiring
5.8.1 Supply Power Connections The LTC 9385 Series housings offer the user one of three If a sealant will be used, be sure it is a neutral cure voltage configurations. The suffix to the housing model type. - Page 11 EN | 11 LTC 9385 Series | Instruction Manual | Installation 4. Connect both the line and neutral wires of the Recommended Maximum Cable Lengths power cord to the terminal block. Make sure Models Wire Size Distance meters feet the line and neutral wires are connected to the...
-
Page 12: Video Coax Connection
EN | 12 LTC 9385 Series | Instruction Manual | Installation LTC 9385/20 Housings Video Coax Connection These housings are to be connected to 24VAC, and WARNING: Only use the cables specified are designed for use where site power is 24volts. The... -
Page 13: Lens Wiring
Wire the functions as described above, or as needed. 5.11 Camera/Lens Orientation Small Fitting A unique feature of the LTC 9385 Series housing is Video Coax Cable CCD Camera BNC Connector the ability to rotate the mounting base 360 º around the rail assembly. -
Page 14: Final Assembly
EN | 14 LTC 9385 Series | Instruction Manual | Installation 3. Insert the long end of the pull seal into the 5.13 Final Assembly breather hole starting from the front side of the 5.13.1 Pull Seal Installation face plate. See FIGURE 16. - Page 15 EN | 15 LTC 9385 Series | Instruction Manual | Installation 3. Align the cover holes with the base assembly 5.13.2 Housing Assembly holes and replace the two M4 screws and 1. The lens support screw is provided to support the rail assembly.
-
Page 16: Exploded View
EN | 16 LTC 9385 Series | Instruction Manual | Exploded View EXPLODED VIEW FIGURE 21 PARTS LIST Drawing Drawing Qty. Part Description Qty. Part Description Mounting Base Assembly Kit - 315 2805 001 115VAC Heater-Bracket Assembly Kit - 315 2809 001...