9. Safety Check - Upon completion of servicing or repairs to the unit, ask the service technician to perform safety checks to ensure proper operating condition. Bosch Security Systems | September 1, 2004...
2. Mechanical Loading - Mounting of the equipment in a rack shall be such that a hazardous condition is not achieved due to uneven mechanical loading. Bosch Security Systems | September 1, 2004...
El cable in werking als de aan-uitschakelaar aan staat. Het netsnoer is de de alimentación es la principal fuente de desconexión de todas "hoofdschakelaar" voor alle apparatuur. las unidades. Bosch Security Systems | September 1, 2004...
Page 5
ON. O fio de alimentação destina-se a desligar a solo quando l'interruttore ON-OFF si trova nella posizione ON. Il corrente em todas as unidades. cavo di alimentazione costituisce il dispositivo di scollegamento dell'alimentazione principale per tutte le unità. Bosch Security Systems | September 1, 2004...
Cable Tie 4.1.1 NEMA-3R and IP54 BHCS, 1⁄4-20 x 1⁄4in. The LTC 9384 Series Housings include a breather hole BHCS, 1⁄4-20 x 5⁄8in. in the front face cap. The breather hole prevents the BHCS, 1⁄4-20 x 3⁄4in. accumulation of moisture inside the housing when BHCS, 1⁄4-20 x 1⁄2in.
EN | 8 LTC 9384 Series | Instruction Manual | Installation Maximum Camera/Lens Size: Input Power Cord - European LTC 9384/xx: Cable Type H05RN-F3G0.75 and Accepts cameras up to 64W x 54H mm (2.5 x 2.1in.), H05RN-F3G1.00 lenses up to 67W x 75H mm (2.6 x 2.9in.), and Cable Size Outside diameter between 4.3mm...
EN | 9 LTC 9384 Series | Instruction Manual | Installation Securely tighten all fittings to ensure a liquid- 5.5 Camera/Lens Installation tight seal. Failure to do so could allow water to With the cradle removed from the housing, place the enter the housing and damage the camera and camera/lens combination into the cradle assembly.
Page 10
EN | 10 LTC 9384 Series | Instruction Manual | Installation to do so will allow water to enter and damage 5.6.3 Power Connections all electronic parts. Use a tie wrap (included) to The LTC 9384 Series Housings (except the...
Page 11
EN | 11 LTC 9384 Series | Instruction Manual | Installation To Heater/Defogger For 24 Volt Cameras: 1. Installing a 24 volt camera into the Black White/ LTC 9384/60 Housing uses the internal Black transformer for camera power (see FIGURE 7).
EN | 12 LTC 9384 Series | Instruction Manual | Installation For 24 Volt Cameras: Install the 3⁄8in. NPT plug provided in the 1. Installing a 24 volt camera into the LTC 9384/50 unused, small top center NPT hole. housing uses the internal transformer for camera Securely tighten all fittings to ensure a liquid- power (see FIGURE 11).
Page 13
EN | 13 LTC 9384 Series | Instruction Manual | Installation Front Endcap Front Face Rear Face of Head Should Be Flush with Front Face Grip and Pull of Front Endcap Breather Hole FIGURE 12 Breather Hole FIGURE 15 Installing the Pull Seal 5.9.2...
EN | 14 LTC 9384 Series | Instruction Manual | Exploded View EXPLODED VIEW FIGURE 17 HARDWARE KIT PARTS LIST Hardware Kit - 315 1514 005 Part Part Quantity Part Description Number Qty. Description Cable Tie Heyco Fitting Kit – 315 3802 001 BHCS, ⁄...
Page 15
EN | 15 LTC 9384 Series | Instruction Manual | Bosch Security Systems | September 1, 2004...